Instrukcja obsługi Whirlpool WUI75X15HZ
Whirlpool
Maszyna do kostek lodu
WUI75X15HZ
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Whirlpool WUI75X15HZ (26 stron) w kategorii Maszyna do kostek lodu. Ta instrukcja była pomocna dla 9 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek
Strona 1/26
1
How Your Ice Maker Works
When you rst start your ice maker, the water pan will ll and the
system will rinse itself before starting to make ice. The rinsing process
takes about 5 minutes.
Under normal operating conditions, the ice maker will cycle at preset
temperatures. The ice level sensor located in the ice storage bin will
monitor the ice levels.
IMPORTANT: If the water supply to the ice maker is turned off, be
sure to set the ice maker control to OFF.
The Ice Making Process
1. Water is constantly circulated over a freezing plate. As the water
freezes into ice, the minerals in the water are rejected. This
produces a sheet of ice with a low mineral content.
User Guide
Ice Maker
LEARN MORE
In an effort to conser e ma a cove natural resource ths, is ic ker incl es ud ndensed User Guide. A complete User Guide can
be downloaded at www.whirlpool.com/manuals. The mode number l is located on e inth side of th e mae ic ker.
In e th U.S.A., register your ice maker at www.w .comhirlpool .
In da register ur Cana , yo ice maker at www.whirlpool.ca.
Para a instun version de estas rucciones en español, visite www.whirlpool.com.
You can be killed or seriously injured if you don’t immediately f .ollow instructions
You ca be killed or seriously injured if u don’t llow instructions.n yo fo
All sa ty messages will tell you what the potential hazard is, tell you how to reduce the chance of injur and tell you what can happen if thefe y,
inst ctions are not llowed.ru fo
Your safety and the safety of othe are very important.rs
We ha provided ma impove ny rtant sa ty messages in this manual and on your appliancfe e. Al ys read and obey all sa ty messagewa fe s.
This is the sa ty alert symbol.fe
This symbol alerts you to potential hazards that can kill or hurt you and others.
All sa ty messages will ll the sa ty aler “DANGER” or “WARNINGfe fo ow fe t symbol and either the word .”
These words mean:
DANGER
WARNING
IMPORTANT SAFETY INSTRUCTIONS
WARN G IN : To reduce the risk of fire, electric shock, or injury when using your ice maker, follow these basic
precautions:
SAVE THESE INSTRUCTIONS
P glug into a rounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do ot se an extension cord.n u
Disconnect power before cleaning.
Disconnect power before servicing.
Replace al nelsl parts and pa before operating.
Use two or more people to move and install ice maker.
Stat of alifornia Propositio 65 rnings:e C n Wa
WARNING This produc contains one or more hemical kn to th Stat of California to cause cancer.: t c s own e e
WARNING This produc contains one or more hemical kn to th Stat of California to cause bi de ct or othe reproductiv ha .: t c s own e e rth fe s r e rm
OPERATING YOUR ICE MAKER
W11256912A
11 Jun 2018 15:29:29 EDT | RELEASED
In some European factories the letter "W" of the part code mentioned herein will be automatically
replaced by the number "4000" (e g "W12345678" becomes "400012345678")
2
2. When the desired thickness is reached, the ice sheet is released
and slides onto a cutter grid. The grid divides the sheet into
individual cubes.
3. The water containing the rejected minerals is drained after each
freezing cycle.
4. Fresh water enters the machine for the next ice making cycle.
5. Cubes fall into the storage bin. When the bin is full, the ice maker
shuts off automatically and restarts when more ice is needed. The
ice bin is not refrigerated, and some melting will occur. The
amount of melting varies with room temperature.
NOTE: As the room and water temperatures vary, so will the amount
of ice produced and stored. This means that higher operating
temperatures result in reduced ice production.
Using the Controls
1. To start ice production, press ON/OFF.
2. To stop ice maker operation, press ON/OFF.
NOTES:
■
Pressing the ON/OFF button does not shut off power to the ice
maker.
■
Allow 24 hours to produce the rst batch of ice. Discard the rst 2
batches produced.
FAST ICE Mode
Select the FAST ICE feature when you have an upcoming need for a
large amount of ice and the ice bin is low or empty. FAST ICE mode
will produce a greater quantity of ice in a 24-hour period.
■
Press FAST ICE while the ice maker is on. The indicator light will
illuminate.
■
Press FAST ICE again to turn off the FAST ICE feature. The
indicator light will turn off.
■
The FAST ICE mode will be on when you rst turn on the product.
It will turn off after 24 hours. To turn FAST ICE back on,
press FAST ICE.
Clean
It is recommended that you clean the ice maker when the “Cleaning
Needed” light is illuminated or 9 months has elapsed, or ice
production decreases signicantly. To clean your ice maker, see
“Ice Maker System” in the “Cleaning” section.
Door Ajar Alarm
The Door Ajar Alarm feature sounds an alarm when the ice maker
door is open for 5 minutes. The alarm will repeat every 2 minutes.
Close the door to turn off. The feature then resets and will reactivate
when the door is left open again for 5 minutes.
Water Filtration System
Installing a Water Filter
1. Purchase a Whirlpool approved water lter.
2. Take the water lter out of its packaging and remove the cover
from the O-rings. Be sure the O-rings are still in place after the
cover is removed.
3. The water lter compartment is located in the right-hand side of
the ice maker controls.
4. Using the arrow pointing to the alignment pin on the side of the
lter and the arrow inside the control housing, align the alignment
pin with the cutout notch and insert the lter into the housing.
Do not use with ter that is microbiologically unsa or wa fe
of unknown quality without adequate disin ction before fe
or after the system. Systems certified r cyst reduction fo
may be used on disinfected ters that may contain wa
filterable cysts.
A B C D
A. Cover
B. O-rings
C. Alignment pin
D. Alignment arrow
A
C
B
D
E
F
A. Alignment pin
B. Unlocked symbol
C. Locked symbol
D. Cutout notch inside control housing
E. Arrow pointing to cutout notch
F. Arrow pointing to alignment pin
11 Jun 2018 15:29:29 EDT | RELEASED
In some European factories the letter "W" of the part code mentioned herein will be automatically
replaced by the number "4000" (e g "W12345678" becomes "400012345678")
3
5. Turn the lter clockwise until it locks into the housing. Ensure
that the alignment arrow on the lter head aligns with the locked
symbol on the control box housing.
NOTE: If the lter is not correctly locked into the housing, the ice
maker will not produce ice.
The Water Filter Status Light
The water lter status lights will help you know when to change your
water lter.
■The “Order Filter” status light will be illuminated when it is time to
order a replacement lter.
■The “Replace Filter” status light will be illuminated when it is time
to replace the lter.
■Replacing the disposable water lter with a new lter will
automatically reset the lter status tracking feature. See “Using
the Controls.”
Replace the Water Filter
To purchase a replacement water lter, see “Accessories.”
Replace the disposable water lter when indicated on the water
lter status display or at least every 9 months. If the ice making rate
decreases before the Replace Filter light illuminates, then replace the
lter.
1. Locate the water lter compartment in the right-hand side of the
control housing. See Step 3 in the “Install Water Filter” section.
2. Turn the water lter counterclockwise (to the left), and pull it
straight out of the compartment.
NOTE: There may be some water in the lter. Some spilling may
occur.
3. Install the replacement water lter by following steps 2 through 5
in the “Install the Water Filter” section.
Normal Sounds
Your new ice maker may make sounds that are not familiar to you.
Because the sounds are new to you, you might be concerned about
them. Most of the new sounds are normal. Hard surfaces such as
oors, walls and cabinets can make the sounds seem louder than
they actually are. The following describes the kinds of sounds that
might be new to you and what may be making them.
■
You will hear a buzzing sound when the water valve opens to ll
the water pan for each cycle.
■
Rattling noises may come from the ow of the refrigerant or the
water line. Items stored on top of the ice maker can also make
noises.
■
The high-efciency compressor may make a pulsating or high
pitched sound.
■
Water running over the evaporator plate may make a splashing
sound.
■
Water running from the evaporator plate to the water pan may
make a splashing sound.
■
As each cycle ends, you may hear a gurgling sound due to the
refrigerant owing in your ice maker.
■
You may hear air being forced over the condenser by the
condenser fan.
■During the harvest cycle, you may hear a “thud” when the ice
sheet slides from the evaporator onto the cutter grid.
■
When you rst start the ice maker, you may hear water running
continuously. The ice maker is programmed to run a rinse cycle
before it begins to make ice.
■
If the ice maker is connected to a water supply pressure in excess
of 60 psi, you may hear a loud sound during water lling
associated with the ow of water through the inlet valve. Call a
licensed, qualied plumber to determine the best method to
reduce the supply water pressure (50 psi is recommended).
Cleaning
The ice making system and the air-cooled condenser need to be
cleaned regularly for the ice maker to operate at peak efciency and
to avoid premature failure of system components. See the “Ice Maker
System” and the “Condenser” sections.
Exterior Surfaces
Wash the exterior surfaces and gaskets with warm water and mild
soap or detergent. Wipe and dry. We recommend using a clean micro
ber cloth or a soft clean cloth to polish and dry.
For products with a painted or colored exterior, regular use of a good
household appliance cleaner and polish will help protect the nish.
Using paper towels may scratch and/or dull the clear coat of the
painted door.
For products with a ngerprint resistant stainless steel exterior, do
not use soap-lled scouring pads, abrasive or harsh cleaners, any
cleaning product containing chlorine bleach, steel-wool pads, gritty
wash cloths or paper towels. Using these types of products may
scratch and/or dull the clear coat of the ngerprint resistant stainless
steel door.
Ice Maker System
Minerals that are removed from water during the freezing cycle will
eventually form a hard scaly deposit in the water system. Cleaning the
system regularly helps remove the mineral scale buildup. How often
you need to clean the system depends upon how hard your water is.
With hard water of 15 to 20 grains/gal. (4 to 5 grains/liter), you may
need to clean the system as often as every 9 months.
NOTE: Use one 16 oz (473 mL) bottle of approved ice maker cleaner.
To order, see “Accessories.”
1. Press the ON/OFF button.
2. Wait 5 to 10 minutes for the ice to fall into the storage bin.
Remove all ice from the storage bin.
3. Unscrew the drain cap from the bottom of the water pan located
inside the storage bin as shown. Allow the water to drain
completely.
A
A. Alignment arrow aligned with locked symbol
CARING FOR YOUR ICE MAKER
11 Jun 2018 15:29:29 EDT | RELEASED
In some European factories the letter "W" of the part code mentioned herein will be automatically
replaced by the number "4000" (e g "W12345678" becomes "400012345678")
Specyfikacje produktu
| Marka: | Whirlpool |
| Kategoria: | Maszyna do kostek lodu |
| Model: | WUI75X15HZ |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z Whirlpool WUI75X15HZ, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje Maszyna do kostek lodu Whirlpool
10 Września 2024
5 Września 2024
4 Lipca 2024
Instrukcje Maszyna do kostek lodu
- Maszyna do kostek lodu Hoshizaki
- Maszyna do kostek lodu Beko
- Maszyna do kostek lodu Gorenje
- Maszyna do kostek lodu SilverCrest
- Maszyna do kostek lodu Maytag
- Maszyna do kostek lodu Domo
- Maszyna do kostek lodu Danby
- Maszyna do kostek lodu Wilfa
- Maszyna do kostek lodu Amana
- Maszyna do kostek lodu Emerio
- Maszyna do kostek lodu H.Koenig
- Maszyna do kostek lodu OneConcept
- Maszyna do kostek lodu Klarstein
- Maszyna do kostek lodu KitchenAid
- Maszyna do kostek lodu AFK
- Maszyna do kostek lodu Bartscher
- Maszyna do kostek lodu G3 Ferrari
- Maszyna do kostek lodu Duronic
- Maszyna do kostek lodu Kenmore
- Maszyna do kostek lodu True
- Maszyna do kostek lodu JennAir
- Maszyna do kostek lodu Frigidaire
- Maszyna do kostek lodu Scotsman
- Maszyna do kostek lodu Summit
- Maszyna do kostek lodu Whynter
- Maszyna do kostek lodu Avanti
- Maszyna do kostek lodu Sonnenkönig
- Maszyna do kostek lodu Atosa
- Maszyna do kostek lodu Igloo
- Maszyna do kostek lodu Trebs
- Maszyna do kostek lodu CaterCool
- Maszyna do kostek lodu Costway
- Maszyna do kostek lodu Manitowoc
- Maszyna do kostek lodu Weasy
- Maszyna do kostek lodu BREND
- Maszyna do kostek lodu XO
- Maszyna do kostek lodu Girmi
- Maszyna do kostek lodu Vivreau
- Maszyna do kostek lodu Royal Catering
- Maszyna do kostek lodu MasterFrost
- Maszyna do kostek lodu ICETRO
- Maszyna do kostek lodu Thermostar
Najnowsze instrukcje dla Maszyna do kostek lodu
14 Października 2024
14 Października 2024
9 Października 2024
9 Października 2024
8 Października 2024
8 Października 2024
8 Października 2024
8 Października 2024
8 Października 2024
8 Października 2024