Instrukcja obsługi Whirlpool WIS 9040 PEL

Whirlpool Pomywaczka WIS 9040 PEL

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Whirlpool WIS 9040 PEL (33 stron) w kategorii Pomywaczka. Ta instrukcja była pomocna dla 3 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/33
1
EN
Before using the appliance carefully read Safety Instructions guide.
APPLIANCE
PRODUCT DESCRIPTION
1. ON/OFF button
2. PREVIOUS button
3. NEXT button
4. Multizone button
5. Display
6. Multizone indicator lights
7. Eco program indicator light
8. Start Delay indicator light
9. Program number and remaining time indicator
10. Closed water tap indicator light
11. Rinse Aid rell indicator light
12. Salt rell indicator light
13. Tablet Detergent (All-in-one) indicator light
14. Tablet Detergent (All-in-one) button with indicator light
15. Turbo button with indicator light
16. Power Clean® button with indicator light
17. Start Delay button with indicator light
18. START button with indicator light
CONTROL PANEL
1
7
2
3
4
6
5
11
13
12
10
8
9
0000 000 00000
Service:
1. Upper rack
2. Cutlery rack
3. Foldable aps
4. Upper rack height adjuster
5. Upper spray arm
6. Power Clean support
7. Lower rack
8. Lower spray arm
9. Filter Assembly
10. Salt reservoir
11. Detergent and Rinse Aid dispensers
12. Rating plate
13. Control panel
1 2 3 4 5 6 7 8 9 10 12 13 14 15 16 17 1811
INSTRUCTION FOR USE
THANK YOU FOR BUYING A WHIRLPOOL PRODUCT.
In order to receive a more complete assistance, please register your appliance on:
www.whirlpool.eu/register
2
FIRST TIME USE
SETTING MENU AND SALT
ADVICE REGARDING THE FIRST TIME USE
After installation, remove the stoppers from the racks and the retaining
elastic elements from the upper rack.
SETTING MENU
1. Switch on the appliance by pressing the button.ON/OFF
2. Switch o the appliance by pressing the button.ON/OFF
3. Hold down START button for 5 seconds, until you hear a beep.
4. The display shows the rst available setting (letter „A”), followed by
its value (for example: 3).
5. Press PREVIOUS/NEXT button to scroll the list of the available settin-
gs and to see their value (see the below table), then press START if you
want to change the value of the displayed setting: its value will start
blinking.
6. Use PREVIOUS/NEXT button to change the blinking value of the se-
lected settings, then press START to save the new value: it will stop
blinking.
7. To change another settings repeat steps 5-6.
8. To exit settings menu - press button. ON/OFF
LETTER SETTING VALUES
(Default - in bold)
Water Hardness Level
(see “SETTING THE WATER HARDNESS”
and “WATER HARDNESS TABLE”)
1 | 2 | | 4 | 53
Rinse Aid Level
(see “ADJUSTING THE DOSAGE OF
RINSE AID”)
1 | 2 | 3 | 4 | 5
Start Program
To set the cycle to show at switch on
of the appliance.
“E”= Eco, “L”= Last cycle run
E | L
Brightness Level
To adjust the brightness
level of the display.
“Lo”=Low, “Hi”= High
Lo | Hi
Sound Level
To adjust the volume of the sounds.
“OF” = sounds o, “Lo” = low volume,
“Hi” = high volume.
OF | Lo | Hi
Light on the Floor
(see OPTIONS AND FUNCTIONS)
“On” = On, “OF” = O
On | OF
Factory Settings
To restore to the factory default all
the values of the settings includ-
ed in the settings menu. After the
activation of this setting (ON), the
machine switches OFF and restores
the factory settings.
“On” = On, “OF” = O
On | OF
NaturalDry
(see “OPTIONS AND FUNCTIONS”)
“On” = On, “OF” = O
On | OF
FILLING THE SALT RESERVOIR
The use of salt prevents the formation of LIMESCALE on the dishes and
on the machine’s functional components.
• It is mandatory that THE SALT RESERVOIR NEVER BE EMPTY.
• It is important to set the water hardness.
The salt reservoir is located in the lower part of the dishwasher
(see PRODUCT DESCRIPTION) and must be lled when the SALT REFILL
indicator light in the control panel is lit.
1. Remove the lower rack and unscrew the
reservoir cap (anticlockwise).
2. Only the rst time you do this: ll the salt
reservoir with water.
3. Position the funnel (see gure) and ll the salt
reservoir right up to its edge (approximately
1 kg); it is not unusual for a little water to leak
out.
4. Remove the funnel and wipe any salt residue
away from the opening.
Make sure the cap is screwed on tightly, so that no detergent can get
into the container during the wash program (this could damage the
water softener beyond repair).
As soon as this procedure is complete, run a program without loading.
The “Pre-Wash” program alone is not sucient.
Residual saline solution or grains of salt can lead to corrosion, irreparably
damaging the stainless steel components.
The guarantee is not applicable if faults are caused by such circumstances.
After the salt has been poured into the machine, the SALT REFILL indi-
cator light switches o.
If the salt container is not lled, the water softener and the heating
element may be damaged as a result of limescale accumulation.
Using of Salt is recommended with any type of dishwasher detergent.
Whenever you need to add salt, it is mandatory to complete the pro-
cedure before the beginning of the washing cycle to avoid corrosion.
SETTING THE WATER HARDNESS
To allow the water softener to work in a perfect way, it is essential that
the water hardness setting is based on the actual water hardness in
your house. This information can be obtained from your local water
supplier.
The factory setting is “3” for average water hardness.
To change, follow instructions in section “SETTING MENU”.
Water Hardness Table
Level °dH
German degrees
°fH
French degrees
°Clark
English degrees
1 Soft 0 - 6 0 - 10 0 - 7
2 Medium 7 - 11 11 - 20 8 - 14
3 Average 12 - 16 21 - 29 15 - 20
4 Hard 17 - 34 30 - 60 21 - 42
5 Very hard 35 - 50 61 - 90 43 - 62
3
EN
FIRST TIME USE
RINSE AID AND DETERGENT
WATER SOFTENING SYSTEM
Water softener automatically reduces water hardness, consequently
preventing scale buildup on heater, contributing also to better cleaning
eciency.
This system regenerates itself with salt, therefore it is required to
rell salt container when empty.
Frequency of regeneration depends on water hardness level setting -
regeneration takes place once per Eco cycles with water hardness 6
level set to . 3
Regeneration process starts in nal rinse and nishes in drying phase,
before cycle ends.
• Single regeneration consumes: ~3.5L of water;
• Takes up to 5 additional minutes for the cycle;
• Consumes below 0.005kWh of energy.
FILLING THE RINSE AID DISPENSER
Rinse aid makes dish DRYING easier. The rinse aid dispenser should be A
lled when the in the control RINSE AID REFILL indicator light
panel is lit.
1. Open the dispenser by pressing and pulling up the tab on the lid.B
2. Carefully introduce the rinse aid as far as the maximum (110 ml) ref-
erence notch of the lling space - avoid spilling it. If this happens,
clean the spill immediately with a dry cloth .
3. Press the lid down until you hear a click to close it.
NEVER pour the rinse aid directly into the appliance tub.
ADJUSTING THE DOSAGE OF RINSE AID
If you are not completely satised with the drying results, you can ad-
just the quantity of rinse aid used.
To change, follow instructions in section “SETTING MENU”.
If the rinse aid level is set to 1 (ECO), no rinse aid will be supplied. The
LOW RINSE AID indicator light will not be lit if you run out of rinse aid.
A maximum of 5 levels can be set according to the dishwasher model.
The factory setting is “5”.
• If you see bluish streaks on the dishes, set a low number (2-3).
• If there are drops of water or limescale marks on the dishes, set
a mid-range number (4-5).
A
B
FILLING THE DETERGENT DISPENSER
Usage of detergent not designed for dishwashers may cause mal-
function or damage to the appliance.
To achieve the best washing and drying results, the combined use
of detergent, rinse aid liquid and rened salt is required.
We recommend using detergents that do not contain phosphates
or chlorine, as these products are harmful to the environment.
Good washing results also depend on the correct amount of detergent
being used.
Exceeding the stated amount does not result in a more eective
wash and increases environmental pollution.
The amount can be adjusted to the soil level. In the case of normally
soiled items, use approximately either 35g (powder detergent)
or 35ml (liquid detergent) and additional tea spoon of detergent
directly inside the tub. If tablets are used, one tablet will be enough.
If the crockery is only lightly soiled or if it has been rinsed with
water before being placed in the dishwasher, reduce the amount
of detergent used accordingly (minimum 25 g/ml) e.g. skip the
powder/gel putted inside the tub.
To open the detergent dispenser press button C. Introduce the
detergent into the dry dispenser D only. Place the amount of
detergent for pre-washing directly inside the tub.
1. When measuring out the detergent
refer to the mentioned earlier infor-
mation to add the proper quantity..
Inside the dispenser there are indiD-
cations to help the detergent dosing.
2. Remove detergent residues from
the edges of the dispenser and clo-
se the cover until it clicks.
3. Close the lid of the detergent
dispenser by pulling it up until the
closing device is secured in place.
The detergent dispenser automatically opens up at the right time
according to the program.
If all-in-one detergents are used, we recommend using the TABLET
DETERGENT button, because it adjusts the program so that the best
washing and drying results are always achieved.
If you are using a all-in-one detergents, we recommend that you
add salt in any case, especially if the water is hard or very hard
(follow the instructions given on the packaging).
C
D

Specyfikacje produktu

Marka: Whirlpool
Kategoria: Pomywaczka
Model: WIS 9040 PEL

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Whirlpool WIS 9040 PEL, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje Pomywaczka Whirlpool

Whirlpool

Whirlpool WIC 3C23 PF Instrukcja

4 Grudnia 2024
Whirlpool

Whirlpool WFC 3C26 F X Instrukcja

4 Grudnia 2024
Whirlpool

Whirlpool WFO 3T132 X Instrukcja

4 Grudnia 2024
Whirlpool

Whirlpool WIO 3O26 PL Instrukcja

4 Grudnia 2024
Whirlpool

Whirlpool WI 7020 PEF Instrukcja

4 Grudnia 2024
Whirlpool

Whirlpool WIO 3T226 PFG Instrukcja

4 Grudnia 2024
Whirlpool

Whirlpool WIS 9040 PEL Instrukcja

4 Grudnia 2024
Whirlpool

Whirlpool WFC 3C33 PF Instrukcja

4 Grudnia 2024
Whirlpool

Whirlpool WIS 7030 PEL Instrukcja

4 Grudnia 2024
Whirlpool

Whirlpool WUE 2B26 Instrukcja

4 Grudnia 2024

Instrukcje Pomywaczka

Najnowsze instrukcje dla Pomywaczka

Hanseatic

Hanseatic HG6085C13J7609DS Instrukcja

4 Grudnia 2024
Bauknecht

Bauknecht GSXP 50/1 Power Instrukcja

4 Grudnia 2024
Bauknecht

Bauknecht GSIP 6527 IN Instrukcja

4 Grudnia 2024
Asko

Asko DFI544K/1 Instrukcja

4 Grudnia 2024
Exquisit

Exquisit GSP9112-030E Instrukcja

4 Grudnia 2024
Exquisit

Exquisit EGSP1009-EB-030E Instrukcja

4 Grudnia 2024
Exquisit

Exquisit EGSP9309-EF-030E Instrukcja

4 Grudnia 2024
Exquisit

Exquisit GSP9109-030E Instrukcja

4 Grudnia 2024
Exquisit

Exquisit GSP9312-060E Instrukcja

4 Grudnia 2024
Exquisit

Exquisit GSP9310-060E Instrukcja

4 Grudnia 2024