Instrukcja obsługi Whirlpool WHVS 90F LT A K

Whirlpool Okap wyciągowy WHVS 90F LT A K

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Whirlpool WHVS 90F LT A K (3 stron) w kategorii Okap wyciągowy. Ta instrukcja była pomocna dla 2 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/3

Quick guide

THANK YOU FOR BUYING A WHIRLPOOL PRODUCT

In order to receive a more complete assistance, please

Before using the appliance carefully read the Safety

Instruction.

PRODUCT DESCRIPTION

FIRST TIME USE

AIR VENT (FOR THE SUCTION VERSIONS)

Connect the hood and discharge holes on the walls with a diameter

equivalent to the air outlet (connection ange).

Using the tubes and discharge holes on walls with smaller dimensions

will cause a diminution of the suction performance and a drastic

increase in noise.

Any responsibility in the matter is therefore declined.

!Use a duct of the minimum indispensable length.

!Use a duct with as few elbows as possible (maximum elbow angle: 90°).

!Avoid drastic changes in the duct cross-section.

!The company declines any responsibility whenever these regulations

are not respected.

FILTERING OR DUCTING?

!Your cooker hood is ready to be used in suction version.

To use the hood in ltering version the special ACCESSORY KIT must be

installed.

Check if the ACCESSORY KIT is furnished or must be bought separately.

Note: If furnished, in certain cases, the additional activated carbon ltering

system may be installed on the hood. Information about the conversion of

the hood from suction version to ltering version is present in the Manual

“Safety Instructions & Installation”.

DUCTING VERSION

In this case the fumes are conveyed outside of the building by means

of a special pipe connected with the connection ring located on top of

the hood.

Attention! The exhausting pipe is not supplied and must be purchased

apart. Diameter of the exhausting pipe must be equal to that of the

connection ring.

Attention! If the hood is supplied with active charcoal lter, then it

must be removed.

FILTER VERSION

The aspirated air will be degreased and deodorised before being fed

back into the room.

In order to use the hood in this version, you have to install a system of

additional ltering based on activated charcoal.

CONTROL PANEL

T1 T2 T3 T4 T5 T6 T7 T8 T9 T10 T11SL1 SL2

T1. Night light ON / OFF

T2. Hob lights ON/ OFF – Select the colour

temperature

T3. "ZEN mode" function

T4. Motor ON / OFF

T5. "POWER BOOST 1" function

T6. "POWER BOOST 2" function

T7. Automatic "Cook Sense" function

T8. Filter saturation indicator

T9. "Daily air sense" operating mode

ON / OFF

T10. "Intensive air sense" operating mode

ON / OFF

T11. "Anti-condensation function" ON / OFF

T1. NIGHT LIGHT ON/OFF

Press to switch the soft background lighting on or o.

T2. HOB LIGHTS ON/OFF – SELECT THE COLOUR TEMPERATURE

Press to switch the hob lights on or o:

• With the lights on, use your nger to swipe right or left over the

SL1 LED strip to increase or decrease the intensity of the light.

Press (and hold) again to set the colour temperature of the lighting:

• Use your nger to swipe right or left over the LED strip to set SL1

the intensity of the light colder or warmer.

If you do not change the colour for ve seconds, will ash at the SL1

colour setting you have selected and an audible signal will sound to

indicate that the system has saved this conguration.

Please note: The light will come on at the last intensity you set before

switching the appliance o.

T3. "ZEN MODE" FUNCTION

Press to activate or deactivate "ZEN" extraction mode.

This function makes it possible to activate an extraction speed with the

perfect balance between quietness and (extraction) eciency.

T4. MOTOR ON/OFF

Press to switch the on or o:extraction motor

• With the motor on, use your nger to swipe right or left over the

SL2 LED strip to increase or decrease the extraction speed (power).

T5. "POWER BOOST 1" FUNCTION

With the extraction motor on, press to activate the speed (power) of T5

"POWER BOOST 1" intensive extraction (time-controlled).

Please note: The hood will go back to running at the speed it was

previously using after ve minutes.

T6. "POWER BOOST 2" FUNCTION

With the extraction motor on, press to activate the speed (power) of T6

"POWER BOOST 2" intensive extraction (time-controlled).

Please note: The hood will go back to running at the speed it was

previously using after ve minutes.

T7. AUTOMATIC "COOK SENSE" FUNCTION

The hood will increase the extraction speed (power) to automatically 1

if the sensor in the hood detects that the ambient conditions require

this.

If the ambient conditions do not change – and the hood is already

using extraction speed (power) 1 – the hood will switch o after ve

minutes.

Please note: To make sure this function is used correctly, please congure

the parameters for automatic mode as described in the relevant section.

Please note: When using automatic mode, if you change any other

functions that control the speed, the auto-ventilation function will switch

o.

T8. FILTER SATURATION INDICATOR

At regular intervals, the hood signals the need to perform lter

maintenance.

Please note: The indicators will only work when the hood is on.

T8 button lit: Carry out maintenance on the grease lter.

T8 button ashing: Carry out maintenance on the active carbon lter.

Resetting the lter saturation indicators:

Please note: This must be done with the hood switched on.

Press and hold the T8 button.

Activating the active carbon lter saturation indicator

Please note: This must be done with the extraction motor switched o.

This indicator is usually deactivated – press and hold the T1 and T9

buttons simultaneously to activate the function: The buttons will light

up to indicate activation.

To deactivate the function, press and hold the same buttons ( and T1

T9) again: The buttons will ash briey and then switch o to indicate

deactivation.

T9. "DAILY AIR SENSE" OPERATING MODE ON/OFF

The hood will increase the extraction speed (power) to automatically 1

if the sensor in the hood detects that the ambient conditions require

this.

If the extraction speed does not change owing to the ambient

conditions detected, the hood will switch o after two hours.

The hood will switch o in any case after ve hours in use, regardless of

the operating mode.

Please note: To make sure this function is used correctly, please congure

the parameters for automatic mode rst as described in the relevant

section.

T10. "INTENSIVE AIR SENSE" OPERATING MODE ON/OFF

The hood will increase the extraction speed (power) to automatically 5

if the sensor in the hood detects that the ambient conditions require

this.

If the extraction speed does not change owing to the ambient

conditions detected, the hood will switch o after two hours.

The hood will switch o in any case after ve hours in use, regardless of

the operating mode.

Please note: To make sure this function is used correctly, please congure

the parameters for automatic mode rst as described in the relevant

section.

T11. "ANTICONDENSATION FUNCTION" ON/OFF

The anti-condensation function prevents condensation from

forming on the surface of the hood. Activate as required.

Switching the "Anti-condensation function" ON/OFF: With the motor

switched on, press the button to activate or deactivate the T11

function.

Please note: The hood will remember the last settings you applied before

switching it o and will use them again the next time you switch it on.

Attention: Even if this function is never activated, carry out periodic

maintenance of the condensation pan all the same, as indicated in

the "Maintenance – Cleaning – Maintenance of the condensation pan"

section.

CONFIGURING THE PARAMETERS FOR AUTOMATIC MODE

To make sure that automatic mode is used correctly, you will need to

calibrate the hood and select the hob type (see below).

Calibrating the hood

Please note: This must be done with the appliance on standby, i.e. one

minute after switching o the motor.

Press and hold the T4 button for ve seconds.

Extraction speed (power) 1 will come on and the button will ash to T4

indicate that hood calibration has started (this will take approximately

15 minutes).

Please note: To stop the calibration process, press and hold the button T4

for ve seconds. Calibration will then be invalidated and will therefore

need to be repeated.

Please note: Calibration will be carried out automatically when the power

supply to the product is switched on for the rst time. will ash. Wait 15 T4

minutes for calibration to complete.

Selecting the hob type

Please note: This must be done with the appliance on standby, i.e. one

minute after switching o the motor.

Press and hold the T9 and T10 buttons for ve seconds.

The and buttons will light up.T9 T10

If using gas to power the hob, press the button – the button will T9

ash to indicate that this has been selected.

If using electricity to power the hob, press the button – the button T10

will ash to indicate that this has been selected.

Once pressed, the button will ash for three seconds to indicate that

your selection has been saved.

TECHNICAL DATA

Height (cm) Width (cm) Depth (cm) Ø of exhaust tube (cm)

105 -148.6 89.8 36.9 15 - 12.5 - 12

CLEANING AND MAINTENANCE

CLEANING

• Do not use steam-cleaning equipment.

• Disconnect the appliance from the mains.

Important: do not use corrosive or abrasive detergents. If any such

products unintentionally come into contact with the appliance, clean

the appliance immediately with a damp cloth. Do not use alcohol.

• Clean the surfaces with a damp cloth. If it is very dirty, add a few

drops of washing-up detergent to the water. Finish o with a dry

cloth.

Important: do not use abrasive sponges or metallic scrapers or

scourers. Over time, these can ruin the enamel surfaces.

• Use detergents specically designed for cleaning the appliance

and follow the manufacturer's instructions.

Important: clean the lters at least once a month to remove oil and

grease residue.

MAINTENANCE OF THE GREASE FILTERS

This must be cleaned once a month (or when the lter saturation

indication system - if envisaged on the model in possession - indicates

this necessity) using non aggressive detergents, either by hand or in the

dishwasher, which must be set to a low temperature and a short cycle.

When washed in a dishwasher, the grease lter may discolour slightly,

but this does not aect its ltering capacity.

Open the extractor panel (turn upwards).

Please note: It is not necessary to remove the panel.

Pull out the handle to remove the lter.

Once the lter has been washed and left to dry, proceed in reverse

order to ret the lter.

MAINTENANCE OF THE CHARCOAL FILTER (FOR FILTRATION

MODELS ONLY)

This lter retains the unpleasant odours produced during cooking.

Replace the carbon lter every 4 months.

Fitting or replacing the carbon lter

1. Disconnect the hood from the mains.

2. Open and remove the extractor panel from its housing.

3. Remove the grease lters.

4. Fit one carbon lter on each side, covering both protective grilles

for the motor impeller.

Turn the lters clockwise to secure them to the central pins.

Proceed in reverse order to remove.

Ret the grease lters and extractor panel.

MAINTENANCE OF THE CONDENSATION PAN

The inspection window at the front of the condensation collection pan

allows you to check if the pan is full, or being drained or cleaned.

In any event, the pan must be drained and cleaned AT LEAST once a

week, or more frequently, based on the level of usage of the hood.

The pan can be cleaned by hand or in a dishwasher at low

temperatures on a short cycle.

REPLACING THE LAMPS

The hood is equipped with an LED lighting system.

LEDs ensure excellent illumination, have a service life up to 10 times

longer than traditional bulbs, and oer up to 90% energy savings.

Note: For replacement LED, please contact the Technical After-sales Service

Centre.

TROUBLESHOOTING

Problem Solutions

The appliance does not work. • Check the mains voltage and whether the appliance is connected to the power supply;

• Check that a speed has been selected;

• Switch the appliance o and on again to see if the fault persists.

The hood is not extracting air suciently. • Check that the air extraction speed is set to the desired level;

• Check that the lters are clean;

• Check the air vents for any obstructions.

The hood has turned o during normal

functioning.

• Check that the power has not been disconnected;

• Check that the omnipolar disconnection device has not tripped.

The lamp does not work. • Check the bulb and replace if necessary;

• Check that the bulb has been tted correctly.

You can download the Safety Instructions, User Manual, Product Fiche and Energy data by:

• Visiting our website docs . whirlpool . eu

• Using QR Code

• Alternatively, contact our After-sales Service (See phone number in the warranty

booklet). When contacting our After-sales Service, please state the codes provided on

your product's identication plate.

XXXXX XXXXXXXX X

Mode l

xxxxxxxxxxxx

XXXXX XXXXXXXX X

Mode l

xxxxxxxxxxxx

400011310610

Specyfikacje produktu

Marka:	Whirlpool
Kategoria:	Okap wyciągowy
Model:	WHVS 90F LT A K
Kolor produktu:	Czarny
Waga produktu:	150 g
Wymiary produktu (SxGxW):	27 x 26 x 27 mm

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Whirlpool WHVS 90F LT A K, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą

Twoje imię*

Twój email*

Napisz tutaj swoje pytanie

Instrukcje Okap wyciągowy Whirlpool

Whirlpool WPRU52ASL Instrukcja

8 Stycznia 2025

Whirlpool WPRU75ASL Instrukcja

8 Stycznia 2025

Whirlpool WPRS90ASL Instrukcja

8 Stycznia 2025

Whirlpool AKR 559/2 IX Instrukcja

2 Stycznia 2025

Whirlpool WAH 65 LM X Instrukcja

25 Grudnia 2024

Whirlpool AKR 429 WH Instrukcja

8 Października 2024

Whirlpool AKR 635 WH-1 Instrukcja

8 Października 2024

Whirlpool WHVS 93F LT BSS/1 Instrukcja

7 Października 2024

Whirlpool AKR 754/1 L IX Instrukcja

6 Października 2024

Whirlpool WVI51UC0LS Instrukcja

6 Października 2024

Instrukcje Okap wyciągowy

Najnowsze instrukcje dla Okap wyciągowy

Silverline PRW 800 Instrukcja

15 Stycznia 2025

Silverline STW 600 C Instrukcja

15 Stycznia 2025

CATA F 2260 X Instrukcja

15 Stycznia 2025

Bosch DWK09M760 Instrukcja

15 Stycznia 2025

Zanussi ZHC 1000 x Instrukcja

15 Stycznia 2025

AEG-Electrolux X69453MVO Instrukcja

15 Stycznia 2025

Beko CWB 9441 Instrukcja

15 Stycznia 2025

Bosch DWB097A51 Instrukcja

15 Stycznia 2025

Elica EST630SS Instrukcja

15 Stycznia 2025

Atag WS90211EM Instrukcja

15 Stycznia 2025