Instrukcja obsługi Whirlpool AKT 424/NB/03
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Whirlpool AKT 424/NB/03 (4 stron) w kategorii piec. Ta instrukcja była pomocna dla 25 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek
Strona 1/4
IMPORTANT SAFETY INSTRUCTIONS
YOUR SAFETY AND THE SAFETY OF OTHERS ARE VERY IMPORTANT
This manual and the appliance itself provide important safety messages, to be read and observed at all times.
This is the safety alert symbol, pertaining to safety, which alerts users to potential hazards to themselves and others.
All safety messages will follow the safety alert symbol and either the terms:
DANGER Indicates a hazardous situation which, if not avoided, will cause serious injury.
WARNING Indicates a hazardous situation which, if not avoided, could cause serious injury.
All Safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what
can happen if the instructions are not followed.
- The appliance must be disconnected from the power supply before carrying out any installation work.
- Installation and maintenance must be carried out by a qualied technician, in compliance with the manufacturer s
instructions and local safety regulations. Do not repair or replace any part of the appliance unless specically stated in
the user manual.
WARNING If the information in this manual is not followed exactly, a re or explosion may result
causing property damage or injury.
- Do not store or use gasoline or other ammable vapors and liquids in the vicinity of this appliance.
What to do if you smell gas:
- Do not try to light any appliance.
- Do not touch any electrical switch.
- Do not use any phone in your building.
- Immediately call your gas supplier from a neighbor s phone. Follow the gas supplier s instructions.
- If you cannot reach your gas supplier, call the re department.
- Installation and service must be performed by a qualied installer, service agency or the gas supplier.
- Use appliance in well ventilated rooms only.
The electrical and gas connections must comply with local regulations.
- When the hob is installed, provide a multi-pole circuit breaker with a contact separation of at least 3 mm, that
provides full disconnection.
- Regulations require that the appliance is grounded.
- The power cable must be long enough for connecting the appliance, once tted in its housing, to the power supply
- Use only exible or rigid metal hose for gas connection.
- If necessary, the electrical power cable must be replaced exclusively with a power cable having identical
characteristics to the original supplied by manufacturer (type H05V2V2-F 90 C or H05RR-F). This operation must be
performed by a qualied electrician.
- The manufacturer cannot be held responsible for any injury to persons or animals or damage to property arising from
failure to comply with these requirements.
- Do not use multiple plug adapters or extension cords.
- Do not pull the power supply cord in order to unplug the appliance.
- The electrical components must not be accessible to the user after installation.
- Do not touch the appliance with any wet part of the body and do not operate it when barefoot.
- This hob (class 3) is designed solely for private household use for cooking food. Do not use this appliance as a space
heater to heat or warm the room. Doing so may result in carbon monoxide poisoning and overheating of the hob. The
Manufacturer declines all responsibility for inappropriate use or incorrect setting of the controls.
- The appliance is not intended for use by persons (including children) with reduced physical, sensory or mental
capabilities, or with lack of experience and knowledge of the appliance, unless supervised or previously instructed in
its use by those responsible for their safety.
- Young children should be kept away from the appliance and supervised to ensure that they do not play with it.
- The use of a gas appliance produces heat and humidity in the room. Make sure the room is well-ventilated, or install
an extractor hood with exhaust duct.
- In case of prolonged use, additional ventilation may be necessary (by opening a window or increasing the hood
extraction speed).
- After use, make sure the knobs are in o position and close the main gas supply cock or the gas cylinder valve.
- Overheated oils and fats catch re easily. Always remain vigilant when cooking foods rich in fat, oil or alcohol (e.g.
rum, cognac, wine).
- Keep the packaging materials out of the reach of children.
- Before cleaning or maintenance wait for hob to cool down.
SAVE THESE INSTRUCTIONS
INSTALLATION
After unpacking the hob, make sure that it has not been damaged during transport. In the event of problems, contact the
dealer or your nearest After-sales Service.
TECHNICAL INFORMATION FOR THE INSTALLER
• This product can be embedded in a worktop 20 to 60 mm thick.
• If there is no oven beneath the hob, insert a separator panel that has a surface at least equal to the opening in
the work surface. This panel must be positioned at a maximum distance of 150 mm below the upper surface
of the work surface but, in no case less than 20 mm from the bottom of the hob. In the case that you intend to
install an oven beneath the hob, make sure that it is manufactured by Whirlpool and equipped with a cooling
system. The manufacturer declines all liability if another brand oven is installed beneath the hob.
• Before installation, make sure that:
- the local gas delivery conditions (nature and pressure) are compatible with the settings of the hob (see
the rating plate and injector table);
- the outer surfaces of the furniture or appliances adjacent to the hob are heat resistant according to local regulations;
- this appliance is not connected to a fume exhaust device. It shall be installed in accordance with current
installation regulations. Particular attention shall be given to the relevant requirements regarding ventilation;
- combustion products are discharged outdoors through specic hoods or wall and/or window mounted
electrical fans.
GAS CONNECTION
WARNING This operation must be performed by a qualied technician.
• The gas supply system must comply with local regulations.
• You can nd specic local regulations for some countries in the paragraph
Reference to Local Regulations . If no information concerning your Country is
given, please ask details to your Installer.
• The connection of the hob to the gas pipe network or gas cylinder must be
made by means of a rigid copper or steel pipe with ttings complying with
local regulations, or by means of a continuous-surface stainless steel hose
complying with local regulations. The maximum length of the hose is 2 linear
metres.
• Connect elbow ( )* or ( )* supplied with to the hob inlet main pipe and A B
interpose the washer ( ) supplied, in compliance with EN 549.C
* Use elbow (A) for France and elbow (B) for all other destinations.
IMPORTANT: if a stainless steel hose is used, it must be installed so as not to
touch any mobile part of the furniture. It must pass through an area where
there are no obstructions and where it is possible to inspect it on all its length.
• After connection to the gas supply, check for leaks with soapy water. Light up
the burners and turn the knobs from max position to minimum position
to check ame stability.
C
C
A
C
B
5019 319 01775 Manufacturer: Whirlpool Europe S.r.l. Viale G. Borghi, 27 21025 Comerio (VA) ITALY
AKT 424 BUILT-IN GAS HOB
EN AE
ELECTRICAL CONNECTION
WARNING This operation must be performed by a qualied technician.
WARNING • The electrical connections must
comply with local regulations.
• The earthing of this appliance is
compulsory by law.
• Do not use an extension cord. •
L
Earth
(yellow/green)
N
IMPORTANT: the data relevant to the voltage and power absorption are indicated on the rating plate.
ASSEMBLY
After having cleaned the perimeter surface, apply
the supplied gasket to the hob as shown in the
gure.
Position the hob in the worktop opening made respecting the dimensions indicated in the Instruction.
NOTE: the power supply cable must be long enough to permit its upward extraction.
To secure the hob, use the brackets ( ) provided with it. Fit the brackets into the relevant bores shown by the arrow A
and fasten them by means of their screws in accordance with the thickness of the worktop (see the following gures).
Top 20 mm Top 40 mm
20
30
60
40
Top 30 mm Top 60 mm
NO
ADJUSTMENT TO DIFFERENT TYPES OF GAS
WARNING This operation must be performed by a qualied technician.
If the appliance is intended to operate with a dierent gas from the gas type stated on the rating plate and
information label on the top of the hob, change the injectors.
Remove the information label and keep it with the instructions booklet.
Use pressure regulators suitable for the gas pressure indicated in the Instruction.
• The gas nozzles must be changed by After Sales Service or a qualied technician.
• Nozzles not supplied with the appliance must be ordered from After Sales Service.
• Adjust the minimum setting of the taps.
NOTE: when liquid petroleum gas is used (G30/G31), the minimum gas setting screw must be tightened
as far as it will go.
IMPORTANT: should you experience diculty in turning the burners knobs, please contact the After
Sales Service for the replacement of the burner tap if found to be faulty.
REPLACING THE INJECTORS (see the injector table in the Instruction)
• Remove grids ( ).A
• Extract burners ( ).B
• Using a socket spanner of the appropriate size
unscrew the injector ( ), unscrew the injector to C
be replaced.
• Replace it with the injector suitable for the new
type of gas.
• Re-assemble the injector in ( ).D
• If you have a multiple crown burner use side
spanner to replace the injector ( ).E
Before installing the hob, remember to ax the gas
calibration plate supplied with the injectors in such a
way that it covers the existing information relating to
gas calibration.
ADJUSTING MINIMUM GAS SETTING OF TAPS
To ensure that the minimum setting is correctly adjusted, remove the knob and
proceed as follows:
• tighten screw to reduce the ame height (-);
• loosen screw to increase the ame height (+).
The adjustment must be performed with the tap in minimum gas setting
position (small ame) .
• The primary air of the burners does not need to be adjusted.
• At this stage, light up the burners and turn the knobs from max position
to minimum position to check ame stability.
Upon completion of adjustment, reseal using sealing wax or an equivalent
material.
REFERENCE TO LOCAL REGULATIONS
Ensure that the installation and gas connections are performed by a qualied technician, following the
manufacturer's instructions and in compliance with current local safety regulations.
AFTER-SALES SERVICE
Before calling the After-Sales Service, make sure you can give the following
information:
- type of fault or problem;
- exact model (written on the label axed to the instruction/warranty);
- service number that follows the word SERVICE on the rating plate under the
hob and on the label axed to instruction/warranty;
- your complete address and phone number.
- If any repairs are required, please contact an authorised After-Sales Service, as
indicated in the warranty.
TROUBLESHOOTING GUIDE
If the hob will not operate correctly, before calling the After-Sales Service, refer to the Troubleshooting Guide to
determine the problem.
1. The burner fails to ignite or the ame is not even
Check that:
• The gas or electrical supplies are not shut o and especially that the gas supply tap is open.
• The gas cylinder (liquid gas) is not empty.
• The burner openings are not clogged.
• The plug end is not dirty.
• All the burner parts have been positioned correctly.
• There are no draughts near the hob.
2. The burner does not stay lit
Check that:
• When lighting the burner, the knob has been pressed for enough time to activate the protection
device.
• The burner openings are not clogged near the thermocouple.
• The end of the safety device is not dirty.
• The minimum gas setting is correct (see relevant paragraph).
3. The containers are not stable
Check that:
• The bottom of the container is perfectly at
• The container is centered on the burner.
• The grids have not been exchanged or positioned incorrectly.
If after the above checks the fault still occurs, get in touch with the nearest After Sales Service.
CLEANING THE HOB SURFACE
WARNING Disconnect power before servicing.
• All the enamelled and glass parts should be cleaned with warm water and neutral solution.
• Stainless steel surfaces may be stained by calcareous water or aggressive detergents if left in contact for
too long. Any food spills (water, sauce, coee, etc.) should be wiped away before they dry.
• Clean with warm water and neutral detergent, and then dry with a soft cloth or chamois. Remove baked-
on dirt with specic cleaners for stainless steel surfaces.
NOTE: clean stainless steel only with soft cloth or sponge.
• Do not use abrasive or corrosive products, chlorine-based cleaners or pan scourers.
• Do not use steam cleaning appliances.
• Do not use ammable products.
• Do not leave acid or alkaline substances, such as vinegar, mustard, salt, sugar or lemon juice on the hob.
CLEANING THE HOB PARTS
• Grids, burner caps and burners can be removed to be cleaned.
• Clean them by hand with warm water and non-abrasive detergent, removing any food residues and
checking that none of the burner openings is clogged.
• Rinse and dry
• Ret burners and burner caps correctly in the respective housings.
• When replacing the grids, make sure that the panstand area is aligned with the burner.
• Models equipped with electrical ignition plugs and safety device require thorough cleaning of the plug
end in order to ensure correct operation. Check these items frequently, and if necessary, clean them with a
damp cloth. Any baked-on food should be removed with a toothpick or needle.
NOTE: to avoid damaging the electric ignition device, do not use it when the burners are not in their
housing.
DECLARATION OF CONFORMITY
• This hob has been designed, constructed and marketed in compliance with:
- safety requirements of “Gas” Directive 2009/142/EC (ex: EEC 90/396);
- safety objectives of the “Low Voltage” Directive 2006/95/EC (which replaces 73/23/EEC and
subsequent amendments);
- protection requirements of EEC Directive “EMC” 2004/108/EC.
• This hob is suitable for contact with foodstus and complies with EEC (CE) Regulation n. 1935/2004.
SAFEGUARDING THE ENVIRONMENT
Disposal of packing material
The packing material is 100% recyclable and is marked with the recycle symbol ( ). The various parts of the
packing must therefore be disposed of responsibly and in full compliance with local authority regulations
governing waste disposal.
Scrapping the product
- This appliance is marked in compliance with European Directive 2002/96/EC, Waste Electrical and
Electronic Equipment (WEEE).
- By ensuring this product is disposed of correctly, you will help prevent potential negative consequences
for the environment and human health, which could otherwise be caused by inappropriate waste
handling of this product.
- The symbol on the product or on the accompanying documentation indicates that it should not be
treated as domestic waste but must be taken to an appropriate collection centre for the recycling of
electrical and electronic equipment.
PRODUCT DESCRIPTION
1. Removable panstand grids
2. Auxiliary burner
3. Semi-rapid burner
4. Semi-rapid burner
5. Ultra-rapid burner
6. Auxiliary burner control knob
7. Semi-rapid burner control knob
8. Semi-rapid burner control knob
9. Ultra-rapid burner control knob
Symbols
Tap closed
Maximum ame
Minimum ame
Specyfikacje produktu
| Marka: | Whirlpool |
| Kategoria: | piec |
| Model: | AKT 424/NB/03 |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z Whirlpool AKT 424/NB/03, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje piec Whirlpool
1 Lipca 2024
1 Lipca 2024
26 Czerwca 2024
25 Czerwca 2024
25 Maja 2024
22 Maja 2024
22 Maja 2024
21 Maja 2024
20 Maja 2024
20 Maja 2024
Instrukcje piec
- piec Bauknecht
- piec Ikea
- piec Bertazzoni
- piec Electrolux
- piec DeLonghi
- piec AEG
- piec Balay
- piec Beko
- piec Teka
- piec LG
- piec Smeg
- piec Götze & Jensen
- piec Gram
- piec Amica
- piec Gorenje
- piec Etna
- piec Russell Hobbs
- piec Tefal
- piec Bosch
- piec Xblitz
- piec Candy
- piec Miele
- piec Brentwood
- piec Midea
- piec Severin
- piec Baumatic
- piec Westinghouse
- piec Rinnai
- piec Hendi
- piec Domo
- piec GE
- piec Blaupunkt
- piec Siemens
- piec Grundig
- piec Blomberg
- piec Husqvarna
- piec Concept
- piec Fisher & Paykel
- piec Indesit
- piec Ilve
- piec Unold
- piec Viking
- piec Nodor
- piec CATA
- piec Hotpoint
- piec V-Zug
- piec PKM
- piec Cuisinart
- piec Amana
- piec Dacor
- piec Hotpoint Ariston
- piec Meireles
- piec Schneider
- piec Thetford
- piec CDA
- piec Neff
- piec Corbero
- piec Zanussi
- piec Thermex
- piec Fagor
- piec Koenic
- piec Klarstein
- piec KitchenAid
- piec Mastercook
- piec TriStar
- piec Dimplex
- piec Arçelik
- piec Continental Edison
- piec Atag
- piec Rosieres
- piec G3 Ferrari
- piec Novy
- piec Inventum
- piec SVAN
- piec Mora
- piec AEG-Electrolux
- piec Omega
- piec Pelgrim
- piec Rex
- piec Kernau
- piec JennAir
- piec Frigidaire
- piec Gemini
- piec Chef
- piec Rommelsbacher
- piec Kelvinator
- piec Asko
- piec Aroma
- piec Edilkamin
- piec Belling
- piec De Dietrich
- piec ZLine
- piec Eurom
- piec Sauber
- piec Smith&Brown
- piec Nutrichef
- piec Constructa
- piec Proline
- piec Finlux
- piec Bestron
- piec VIOFO
- piec Optimum
- piec Rotel
- piec Atlas
- piec Kluge
- piec Arthur Martin
- piec Logik
- piec Eldom
- piec Glem Gas
- piec Proctor Silex
- piec Creda
- piec Waves
- piec ARC
Najnowsze instrukcje dla piec
9 Października 2024
1 Października 2024
23 Września 2024
23 Września 2024
22 Września 2024
21 Września 2024
19 Września 2024
18 Września 2024
18 Września 2024
17 Września 2024