Instrukcja obsługi Whirlpool ADPU 603

Whirlpool Pomywaczka ADPU 603

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Whirlpool ADPU 603 (11 stron) w kategorii Pomywaczka. Ta instrukcja była pomocna dla 8 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/11
EN -1-
Chart
KEYBOARD LOCK
This option allows you
to lock the buttons on
the control panel.
Children will not be
able to accidentally
start the dishwasher by
pressing the buttons on
the control panel when
this option is selected.
If you want to activate
this option hold down
the button for
3 seconds.
Repeat the same
operation to unlock the
panel.
TABLET
SETTING
This setting allows
to optimize the
cycle
performances
according the type
of detergent used.
Push the Tablet
button (the
indicator lights up)
if you are using the
combined
detergents in
tablet.
If you are using
powder or gel
detergent, the
Tablet indicator
on the control
panel has to be off.
DELAYED START
BUTTON
Push the button
(repeatedly) to delay the
start of the program.
Adjustable from 0:30 to
24 hours. With each press
of the button, the delay
start increases by: 0:30 if
selection below 4 hours,
1:00 if selection is below
12 hours, 4 hours if
selection is above 12 hours.
If 24 hours reached, and
the button is pressed, the
delayed start is deactivated
- "OFF" message is shown.
Then press the START
button. The delay time can
be adjusted after Start key
press. The dishwasher will
start after the set time.
START/PAUSE/
RESUME
BUTTON
Push this button to
start the selected
program: the
indicator lights up
and goes off at the
end of the program.
Press Start button or
open the door
during washing cycle
to pause the cycle -
the Start Indicator
blinks.
To resume the cycle
push Start button
and close the door.
CANCEL/OFF
BUTTON
Push this button to
switch off the control
panel.
If pressed for 3 seconds
when a program is
running it cancels this
program. If pressed
for 3 seconds when
the dishwasher is off,
it drains the water out.
If pressed during
program and delayed
start selection it
cancels the selection
and returns to
previous cycle and
option selection.
BEFORE USING THE APPLIANCE FOR THE FIRST TIME CAREFULLY READ THIS QUICK REFERENCE GUIDE AND THE ASSEMBLY INSTRUCTIONS!
5019 300 02432
FOR ENERGY SAVING THE CONTROL PANEL DEACTIVATES AUTOMATICALLY AFTER 30 SECONDS IF NO CYCLE HAS STARTED.
ECO PROGRAM
INDICATOR
When lit, it indicates that
standard program is active.
MULTIZONE
INDICATOR
When lit, it indicates the
wash in the upper or lower
rack only.
KEYBOARD LOCK
INDICATOR
When lit, it indicates that
keyboard lock is active.
WATER TAP CLOSED
- Alarm
Blinks when there is no inlet
water or water tap is closed.
WASH TIME DISPLAY
Indicates the cycle duration and the remaining time (h:min). With “Delayed start”
selected it indicates the time remaining until program start: “h24” if above
10 hours delay time remain and “h:mm” if below 10 hours delay time remain.
If “Fx Ey” messages appears on the display, see page 8 - chapter “What to do if...”.
DELAY INDICATOR
When lit, it indicates that delay
is active.
RINSE AID
INDICATOR
When lit (at the end of the
cycle), the rinse aid dispenser
needs to be refilled.
SALT INDICATOR
When lit (at the end of the
cycle), the salt reservoir needs
to be refilled.
MULTIZONE
Allows you to choose
the washing zones.
The appliance washes both
racks by default (indicators
are not lit).
To wash only in specific
rack, press this button
repeatedly:
only upper rack
indicator lit
only lower rack
indicator lit
PROGRAM
SELECTION
BUTTON
Push “P” button
(repeatedly) until
selected
program number
is shown on the
display (P1...Px) -
see “Table of
programs” - next
page.
After 3 seconds
the cycle
remaining time is
displayed.
ANTIBACTERIAL
RINSE
This function activates an
antibacterial rinse at the end of the
wash cycle, guaranteeing a further
reduction of bacteria.
Press the button to activate or
deactivate the function.
This function can be used with the
programs indicated in the table of
programs.
The dishwasher door must be
kept shut for the entire duration of
the program in order to guarantee
reduction of bacteria.
If the door is opened the indicator
lamp starts flashing.
Quick reference guide
Whirlpool is a registered trademark of Whirlpool USA
EN -2-
Chart
1) Program data obtained under normal conditions and with default options on. Data may vary depending on ambient conditions and used options. Differences of up to 20 minutes are possible with sensor programs as
a result of the appliance’s automatic calibration system.
2) Reference program for energy label in compliance with EN 50242 regulations. - Note for Testing Institutes: for detailed information on the EN/Standard loading comparison test and other tests, contact the following
address: “contact@whirlpool.com”.
Power consumption in: Left-on mode: 1.08 W / Off-mode: 0.40 W.
Table of programs Deter-
gent
Consumption
Drying
Phase
Programs Available
options Loading instructions Litres kWh Minutes 1)
P1 Sensor 40-70°C
Delay
Multizone
Antibacterial
Rinse
Recommended program for routine washes, with
dried-on food.. X7.5-13 0.95-1.45 85-175 Full
P2 Pre-Wash cold Delay
Multizone Crockery to be washed later. —4.0 0.01 14-16 NO
P3 Fragile 40°C Delay
Multizone Lightly soiled crockery, for example glasses and cups. X10.5 0.85 105-114 Light
P4 Rapid 45°C Delay
Multizone Lightly soiled crockery, with no dried-on food. X11.0 0.85 30-50 NO
P5 Eco 2) 50°C
Delay
Multizone
Antibacterial
Rinse
Normally soiled crockery.
Standard program the most efficient in terms of its
combined energy and water consumption.
X9.0 0.92 240 Full
P6 Daily 60°C
Delay
Multizone
Antibacterial
Rinse
Normally soiled crockery. X11.0 1.30 80-95 Full
P7 Silent 50°C Delay
Multizone
Normally soiled crockery, gentle and quiet thanks to
the lower spray pressure. X14.0 1.20 290-299 Light
P8 Steam
Delay
Multizone
Antibacterial
Rinse
Program including steam action dedicated for heavily
soiled crockery, pots and pans. Soaking or hand
pretreatment is no longer needed.
X14.5 1.75 180-190 Full
Quick reference guide
EN -3-
First time use
5 786
1
4
10
9
23
1- salt reservoir
2- rinse aid dispenser
3- detergent dispenser
4- racks system
5,6,7,8- available functions on the panel
9- filters
10- spray arms
Water hardness should be set
before the first wash or if water
hardness has been changed
1Visual indicator
(depending
on the model).
Unscrew cap.
Fill the salt reservoir with water
before the first wash only.
(depending on the model)
The salt level indicator lamp may remain lit
at the end of several wash cycles. If the
water hardness is set to level 1 (soft), no
salt is required and salt indicator lamp will
remain off.
Salt indicator on the control panel Salt indicator on the salt reservoir cap
The indicator lamp lights up when
SALT NEEDS TO BE ADDED. green: OK. clear: NEEDS TO
BE ADDED
Daily check
Filling the salt reservoir - Dissolve limescale (not necessary if water hardness level is set to “soft 1”!)
Screw on the cap.
Salt residual
around the cap
needs to be
removed. Some
salt reservoirs
have a level
indicator
integrated in the
cap (see below
how to check).
- Press and hold together Program and buttons for minimum 3 seconds.
- The current water hardness setting will be visible on the display.
- Press the Program button to increase setting. Value range goes from 1 to 7 (when the level reaches 7, the next press of the
start button will set the level back to 1).
- Wait 30 seconds (control panel switches off) or press Start/
Pause
button to save setting.
1. Ask your water supply company what the water hardness is... 2. ...enter this value
on your dishwasher Salt required
German
degrees °dH
French
degrees °fH
English
degrees °eH
Water hardness
level
Insert value is shown
in the display
0 - 5 0 - 9 0 - 6.3 Soft 1NO
6 - 10 10 - 18 7 - 12.6 Medium 2
YES
11 - 15 19 - 27 13.3 - 18.9 Average 3
16 - 21 28 - 37 19.6 - 25.9 Medium-hard 4
22 - 28 38 - 50 26.6 - 35 Hard 5
29 - 35 51 - 63 35.7 - 44.1 Very hard 6
36 - 50 64 - 90 44.8 - 62.4 Extremely hard 7
Add salt (never add detergent!)
min. 0.8 kg/max. 1 kg
Water hardness level is
factory set for medium-hard
water (level 4).
Detergents
When powder or gel
detergent is used,
regeneration salt must be
added and water hardness
level must be set as indicated
in the table on the right.
Also, when tablets which
include salt functionality are
used, regeneration salt still
must be added.
Once regeneration salt is added, immediately start a wash program (the “Pre-wash” program alone is not sufficient).
Residual saline solution or grains of salt can lead to deep-down corrosion, irreparably damaging the stainless steel components.
The guarantee is not applicable if faults are caused by such circumstances.
How to set water hardness in order to always assure the best cleaning results
Before first use, run the appliance with detergent and without loading.

Specyfikacje produktu

Marka: Whirlpool
Kategoria: Pomywaczka
Model: ADPU 603

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Whirlpool ADPU 603, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje Pomywaczka Whirlpool

Whirlpool

Whirlpool WDT740SALB Instrukcja

14 Października 2024
Whirlpool

Whirlpool ADG 522 IX Instrukcja

12 Października 2024
Whirlpool

Whirlpool WFO 3T333 DL X Instrukcja

8 Października 2024
Whirlpool

Whirlpool WFO 3T123 PL Instrukcja

8 Października 2024
Whirlpool

Whirlpool WSIP 4O23 PFE Instrukcja

8 Października 2024
Whirlpool

Whirlpool WSIO 3O34 PFE X Instrukcja

8 Października 2024
Whirlpool

Whirlpool WIP 4O33 PLE S Instrukcja

8 Października 2024
Whirlpool

Whirlpool WIO 3O33 PLE Instrukcja

8 Października 2024
Whirlpool

Whirlpool WIO 3C33 E 6.5 Instrukcja

8 Października 2024
Whirlpool

Whirlpool WIP 4O33N PLE S Instrukcja

8 Października 2024

Instrukcje Pomywaczka

Najnowsze instrukcje dla Pomywaczka

Zanussi

Zanussi ZDV14003FA Instrukcja

15 Października 2024
Bauknecht

Bauknecht GSXK 5011 A+ Instrukcja

15 Października 2024
Midea

Midea MFD60S230X-IT Instrukcja

15 Października 2024
V-Zug

V-Zug GS60Ni3n Instrukcja

15 Października 2024
Miele

Miele G 5051 SCVi Active Instrukcja

15 Października 2024
Freggia

Freggia DWI4108 Instrukcja

15 Października 2024
Küppersbusch

Küppersbusch IG 659 1 Instrukcja

14 Października 2024
Hotpoint

Hotpoint LSTA+ 216 A/HA Instrukcja

14 Października 2024
Grundig

Grundig GNUP4530W Instrukcja

14 Października 2024
Grundig

Grundig GNLP4620X Instrukcja

14 Października 2024