Instrukcja obsługi Whirlpool ADG 4620 IX

Whirlpool Pomywaczka ADG 4620 IX

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Whirlpool ADG 4620 IX (16 stron) w kategorii Pomywaczka. Ta instrukcja była pomocna dla 6 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/16
GB -1-
Chart
START/RESUME BUTTON
Push this button to start the selected program: the
indicator lights up and goes off at the end of the
program.
When the door is opened during a washing cycle,
the cycle is temporarily paused: the Start indicator
blinks. To resume the cycle close the door and
push Start button again.
PROGRAM SELECTION
BUTTON
Push “Programs” button
(repeatedly) until the indicator
of the required program lights
up (see “Table of programs”
below).
CANCEL/OFF BUTTON
Push this button to switch off the control panel.
If pressed when a program is running it cancels the
program ongoing draining water for 1 minute.
If pressed when the dishwasher is switched off it
drains any possible liquids from dishwasher (1
minute process).
If the indicator flashes repeatedly, see page 6 -
chapter ”What to do if ...”.
(see at right for options description)
1) Program data obtained in conformity with European standard EN 50242, obtained under normal conditions (without additional
options) and may vary depending on conditions. Differences of up to 20 minutes are possible with sensor programs as a result of the
appliance’s automatic calibration system.
2) Reference program for energy label in compliance with EN 50242 regulations. - Note for Testing Institutes: for detailed information
on the EN/Standard loading comparison test and other tests,
contact the following address:
“nk_customer@w
hirlpool.com”.
3) The antibacterial action has been tested by the Institut Pasteur of Lille (France), based on the NF EN 13697 standard of November 2001.
Table of programs
Deter-
gent
Consumption
PPrograms Available
options Loading instructions Litres kWh Minutes 1)
1 Pre-Wash cold Delay Crockery to be washed later. — 4.0 0.03 14
2 Quickwash 45°C Delay Lightly soiled crockery, with no dried-
on food. X 11.0 0.80 30
3Eco 2) 50°C Delay Normally soiled crockery.
Energy-saving program. X 12.0 1.05 165
4Antibacterial 3) Delay
Normally or heavily soiled crockery,
with additional antibacterial wash.
Program interruption (e.g. due to door
opening) can compromise elimination
of germs.
X 13.0 1.50 115
5 Intensive 70°C Delay
Recommended program for heavily
soiled crockery, especially suitable for
pans and saucepans.
X 14.0 1.55 155
5019 396 01953ADG 4620
BEFORE USING THE APPLIANCE FOR THE FIRST TIME CAREFULLY READ
THIS QUICK REFERENCE GUIDE AND THE ASSEMBLY INSTRUCTIONS!
Options and display description
SALT INDICATOR
When lit (at the end of the
cycle), the salt reservoir
needs to be refilled.
DELAYED START
BUTTON
The wash cycle can be
programmed to start
after 2, 4 or 8 hours.
Then press the Start
button. The wash
program will start after
the set time.
RINSE AID INDICATOR
When lit (at the end of the
cycle), the rinse aid
dispenser needs to be
refilled.
THE CONTROL PANEL OF THIS DISHWASHER ACTIVATES PUSHING
ANY BUTTON EXCEPT CANCEL/OFF BUTTON.
FOR ENERGY SAVING THE CONTROL PANEL DEACTIVATES
AUTOMATICALLY AFTER 30 SECONDS IF NO CYCLE HAS STARTED.
TABLET SETTING
This setting allows to optimize the cycle performances
according the type of detergent used.
Push the Tablet button for 3 seconds (until the indicator
lights up) if you are using the combined detergents in
tablet (rinse aid, salt and deteregent in 1 dose).
If you are using powder detergent or liquid detergent,
the Tablet indicator on the control panel has to be off.
Quick reference guide
GB -2-
First time use
1- salt reservoir
2- rinse aid dispenser
3- detergent dispenser
4- racks system
5,6,7,8- available functions on the panel
9- filters
10- spray arms
1. Ask your water supply company what the
water hardness is...
2. ...enter this value on your
dishwasher Suggestions for detergent use
French
degrees °fH
Water hardness
level
3 first PROGRAM LEDs
lit on the panel
(see table of programs)
P1 P2 P3
Gel or Powder
(rinse aid and salt) Tabl ets
0 - 9 Soft 1
go to step 1
(see “Daily
check”)
10 - 18 Medium 2
19 - 27 Average 3
28 - 37 Medium-hard 4 if water is
HARD extra salt
needs to be added
(go to step 1,
“Daily check”)
38 - 50 Hard 5
51 - 63 Very hard 6
64 - 90 Extremely hard 7
Water hardness should be set only
before the first wash or if water
hardness has been changed
1Visual indicator
(depending
on the model).
Unscrew cap.
Fill the salt reservoir with water
before the first wash only.
(depending on the model)
The salt level indicator lamp may remain lit
at the end of several wash cycles. If the
water hardness level falls within category
(soft), no salt is required.
Salt indicator on the control panel Salt indicator on the salt reservoir cap
The indicator lamp lights up when SALT
NEEDS TO BE ADDED. green: OK. clear: NEEDS TO
BE ADDED
Daily check
Filling the salt reservoir - Dissolve limescale (not necessary if water hardness level is set to “soft”!)
- Press and hold together Programs and buttons for minimum 3 seconds.CANCEL/Off
- Programs LEDs will indicate the water hardness setting.
- Press the Programs button to increase setting (when the level reaches 7, the next key press will set the level back to 1.
- Wait 30 seconds (control panel switches off) or press START/Resume button to save setting.
Add salt (never add detergent!)
min. 0.8 kg / max. 1 kg
Water hardness level is factory
set for medium-hard water
(level 4).
Even if you use tablets which
include salt functionality, you
must still add regeneration salt
since such detergents are not
effective enough at softening
hard water.
Screw on the cap.
Salt residual
around the cap
need to be
removed. Some
salt reservoir have
a level indicator
integrated in the
cap (see below
how to check).
At first time use, the salt reservoir has to be filled independently from water hardness level (see description below in step 1 “Daily check”).
How to set water hardness in order to always assure the best cleaning results

Specyfikacje produktu

Marka: Whirlpool
Kategoria: Pomywaczka
Model: ADG 4620 IX

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Whirlpool ADG 4620 IX, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje Pomywaczka Whirlpool

Whirlpool

Whirlpool WDT740SALB Instrukcja

14 Października 2024
Whirlpool

Whirlpool ADG 522 IX Instrukcja

12 Października 2024
Whirlpool

Whirlpool WFO 3T333 DL X Instrukcja

8 Października 2024
Whirlpool

Whirlpool WFO 3T123 PL Instrukcja

8 Października 2024
Whirlpool

Whirlpool WSIP 4O23 PFE Instrukcja

8 Października 2024
Whirlpool

Whirlpool WSIO 3O34 PFE X Instrukcja

8 Października 2024
Whirlpool

Whirlpool WIP 4O33 PLE S Instrukcja

8 Października 2024
Whirlpool

Whirlpool WIO 3O33 PLE Instrukcja

8 Października 2024
Whirlpool

Whirlpool WIO 3C33 E 6.5 Instrukcja

8 Października 2024
Whirlpool

Whirlpool WIP 4O33N PLE S Instrukcja

8 Października 2024

Instrukcje Pomywaczka

Najnowsze instrukcje dla Pomywaczka

Zanussi

Zanussi ZDV14003FA Instrukcja

15 Października 2024
Bauknecht

Bauknecht GSXK 5011 A+ Instrukcja

15 Października 2024
Midea

Midea MFD60S230X-IT Instrukcja

15 Października 2024
V-Zug

V-Zug GS60Ni3n Instrukcja

15 Października 2024
Miele

Miele G 5051 SCVi Active Instrukcja

15 Października 2024
Freggia

Freggia DWI4108 Instrukcja

15 Października 2024
Küppersbusch

Küppersbusch IG 659 1 Instrukcja

14 Października 2024
Hotpoint

Hotpoint LSTA+ 216 A/HA Instrukcja

14 Października 2024
Grundig

Grundig GNUP4530W Instrukcja

14 Października 2024
Grundig

Grundig GNLP4620X Instrukcja

14 Października 2024