Instrukcja obsługi Westinghouse 6401235


Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Westinghouse 6401235 (1 stron) w kategorii Lampa. Ta instrukcja była pomocna dla 3 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Strona 1/1
Installation and Safety Instructions
Warning: Electrical shock can result in serious injury.
Read and follow instructions exactly as shown. If instructions are unclear, do not proceed. Contact a qualified electrician. Read
all instructions before beginning. Proper wiring is essential for safe operation of this fixture. When cutting or drilling into walls or
ceilings, do not damage electrical wiring, gas lines, or water lines. If any of the fixture or wiring components are damaged, do not
install fixture. Return to place of purchase.
If the external flexible cable or cord of this luminaire is damaged, it shall be exclusively replaced by the manufacturer or his service
agent or a similar qualified person in order to avoid a hazard.
The light source contained in this luminaire shall only be replaced by the manufacturer or his service agent or a similar qualified person.
For indoor use only.
ASSEMBLY INSTRUCTIONS FOR INDOOR LIGHTING FIXTURE
Congratulations on your Westinghouse purchase. This fixture has been designed to give you many years of beauty
and service. For questions and comments, please visit www.westinghouselighting.eu/contact-us and www.
westinghouselighting.de/contact-us
NOTE: Carefully unpack fixture and parts. Make sure all parts are included before discarding any packing materials (see
figure 1).
MOUNTING AND WIRING INSTRUCTIONS
NOTE: Line art shown may not exactly match the fixture enclosed. However, the installation instructions do apply to this
fixture.
1. Place fixture pan (A) flush against ceiling at desired mounting location. Using outside fixture pan key slot hole
(D) as a guide, make where pilot holes are to be drilled.
2. Drill 4 - 1/8 inch holes at each pencil mark then insert wall anchors (H) by gentlly tapping with a hammer.
3. Thread mounting screws (C) into the anchors approximately ¼ inch (for drywall ceiling).
4. Make an electrical connection by loosening the terminal screws on the terminal block (M) and inserting the
live, neutral and ground terminals.
5. Tighten terminal screws. Make sure there are no stray wires.
6. Raise fixture pan (A) to ceiling allowing mounting screws (C) to protrude through key slots (D) in fixture pan
(A) (see fig.1)
7. Rotate fixture pan (A) clockwise until mounting screws (C) lock into narrow portion of key slots (D). Secure
into place with mounting screws (C).
8. Final assembly - Secure the lens (E) and ring (F) to fixture pan (A) using for cap nuts (G).
CLEANING AND CARE
To clean, wipe fixture with soft cloth. Clean glass with mild soap. Spray from chemical cleaners can discolor the finish of
fixture. Do not use scouring pads, powders, steel wool or abrasive paper to clean this fixture.
NOTE FOR FIXTURES THAT ARE SOLID BRASS:
Your hand-crafted, solid brass lighting fixture has been coated with a durable, baked-on acrylic lacquer which gives
maximum protection against the weather. However, in time the brightness of the brass will tarnish, giving way to an
authentic old-world brass finish. To keep your solid brass fixture looking new for years to come, regularly apply a good
quality, non-abrasive car wax to all metal surfaces, giving the fixture an extra protective covering.
Meaning of crossed-out wheeled dustbin:
Do not dispose of electrical appliances as unsorted municipal waste, use separate collection facilities. Contact you local
government for information regarding the collection systems available.
If electrical appliances are disposed of in landfills or dumps, hazardous substances can leak into the groundwater and get
into the food chain, damaging your health and well-being.
When replacing old appliances with new ones, the retailer is legally obligated to take back your old appliance for disposal
at least free of charge.
Appliance specifications - TECHNICAL CHARACTERISTICS
Westinghouse Lighting, Philadelphia, PA 19154-1029, U.S.A.
www.westinghouselighting.com
, WESTINGHOUSE, and INNOVATION YOU CAN BE SURE OF
are trademarks of Westinghouse Electric Corporation.
Used under license by Westinghouse Lighting.
All rights reserved.
Made in China
W-606
052818
*NOT SUPPLIED
FIGURE 1.
A
B
C
E
D
F
G
H
M
Rated voltage 220-240V~
Rated frequency 50Hz
Rated wattage Integrated LED Max. 25W
Protection class CLASS I
IP number IP20
Ambient temperature 40
o
C


Specyfikacje produktu

Marka: Westinghouse
Kategoria: Lampa
Model: 6401235

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Westinghouse 6401235, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą




Instrukcje Lampa Westinghouse

Instrukcje Lampa

Najnowsze instrukcje dla Lampa