Instrukcja obsługi Wasp WWS800

Wasp czytnik kodów kreskowych WWS800

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Wasp WWS800 (18 stron) w kategorii czytnik kodów kreskowych. Ta instrukcja była pomocna dla 6 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/18

Wasp Technologies WWS800 Cordless Scanner

User’s Manual

Document Number: W800-A1

Release Date: February 18, 2004

 2004, Wasp

Technologies

WARNING

This equipment has been tested and found to comply with the limits for a Class A digital

device, pursuant to Part 15 of FCC Rules. These limits are designed to provide

reasonable protection against harmful interference in a residential installation. This

equipment generates, uses and can radiate radio frequency energy and, if not installed

and used in accordance with the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference will not occur in a

particular installation. If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the equipment off and on, the

user is encouraged to try to correct the interference by one or more of the following

measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Table of Contents

Introduction ........................................................................ 1

Installation .......................................................................... 2

2.1

Power Up the WWS800 Base Station ................................ 2

2.2

Power Up the WWS800 Cordless Scanner......................... 3

2.3

Setup RF Connection.......................................................... 3

2.4

Charging your WWS800 Cordless Scanner........................ 4

2.5

Interface Setting.................................................................. 5

General Features................................................................. 6

3.1

Buzzer................................................................................. 6

3.2

Indicator ............................................................................. 6

3.3

Scan Modes ........................................................................ 6

3.4

Auto-Sense ......................................................................... 7

3.5

Re-read Delay..................................................................... 7

3.6

Scanner Time-out Duration ................................................ 7

3.7

Reading Redundancy .......................................................... 8

3.8

Supported Symbologies ...................................................... 8

3.9

Negative Barcodes.............................................................. 8

Output Interface (WWS800 Base Unit).............................. 9

4.1

Keyboard Wedge Interface ................................................. 9

4.1.1

Keyboard Type ................................................................... 9

4.1.2

Keyboard Style - Alphabets................................................ 9

4.1.3

Keyboard Style – Digits ..................................................... 9

4.1.4

Capital Lock Status........................................................... 10

4.1.5

Alphabets Transmission.................................................... 10

4.1.6

Digits Transmission.......................................................... 10

4.1.7

Inter-Character Delay ....................................................... 10

4.2

USB Interface ................................................................... 10

4.3

Memory Parameters.......................................................... 11

4.3.1

Memory Mode .................................................................. 11

4.3.2

Clear Data......................................................................... 11

4.3.3

Send Data ......................................................................... 11

4.3.4

Memory Data Delay ......................................................... 11

Bluetooth Serial Port ........................................................ 12

5.1

Configuring the WWS800 ................................................ 12

5.1.1

Activate Bluetooth Serial Port Interface........................... 12

5.1.2

Authentication & PIN Code.............................................. 12

5.1.3

Device Name Broadcasting .............................................. 12

5.1.4

Update Settings................................................................. 13

5.1.5

Timeout ............................................................................ 13

5.2

Configuring Bluetooth Device Driver .............................. 13

Symbology Parameters ..................................................... 19

6.1

Code39 ............................................................................. 19

6.2

Italy / French Pharmacode ................................................ 19

6.3

Industrial / Interleave / Matrix 25..................................... 19

6.4

Codabar ............................................................................ 20

6.5

UPCE................................................................................ 20

6.6

EAN8................................................................................ 20

6.7

UPCA ............................................................................... 21

6.8

EAN13.............................................................................. 21

6.9

MSI................................................................................... 21

6.10

Plessey.............................................................................. 21

6.11

Telepen............................................................................. 22

6.12

RSS................................................................................... 22

Data Output Format.......................................................... 23

7.1

Character Substitution ...................................................... 23

7.2

Prefix / Postfix Code ........................................................ 23

7.3

Code ID ............................................................................ 23

7.4

Length Code ..................................................................... 24

Data Editing...................................................................... 25

8.1

Select Editing Format ....................................................... 25

8.2

Restore Default Format .................................................... 25

8.3

Applicable Conditions ...................................................... 25

8.4

Total Number of Fields .................................................... 26

8.5

Dividing Data into Fields ................................................. 26

8.6

Additional Fields .............................................................. 27

8.7

Field Transmission Sequence ........................................... 27

8.8

End of Format Programming ............................................ 27

8.9

Activate Data Editing Formats ......................................... 27

8.10

Exclusive Data Editing ..................................................... 27

8.11

Programming Examples.................................................... 27

Configuring your WWS800.............................................. 29

9.1

Enter Configuration Mode................................................ 29

9.2

Default.............................................................................. 29

9.3

List Setting ....................................................................... 29

9.4

Setting Parameter Values.................................................. 29

9.4.1

Numeric Parameters ......................................................... 30

9.4.2

Character String Parameters ............................................. 30

9.4.3

Key Type/Status Setting ................................................... 31

9.5

Exit Configuration Mode.................................................. 32



 

The WWS800 Cordless Barcode Scanner is the first Wasp Technologies scanner

utilizing Bluetooth Technology. The scanner has a remote range of over 160 feet

and a battery life of over 50,000 scans. The WWS800 uses a CCD long-range

linear imager. This manual contains all the information needed to operate and

configure the WWS800. It is divided into two parts. The first part of this manual

describes the installation, operation and programmable features of the scanner. The

second part of this manual contains the setup barcodes used to configure the

scanner.

The WWS800 is one of the most versatile and flexible cordless barcode scanners

available today. All the features and functions required for up to date barcode

reading are included. Owing to the compact design and extremely low power

consumption, this scanner provides for easy installation and high product durability.

The scanner caters to the requirements of today, while also fulfilling your long-term

needs. The main functions and features provided on the WWS800 are listed below.

• Barcode Readability: Most popular barcode symbologies are supported including

the newest RSS Code.

• Support for negative barcodes.

• Supports eight scan modes.

• Programmable Beeping Tone

• Dual Color Indicator

• Interface Support (base unit): KB Wedge and USB

• Bluetooth Serial Port Profile Support: The scanner can transmit scanned data to

Bluetooth enabled computer/PDA via standard Bluetooth Serial Port

communication.

• Programmable Code ID: Code ID can be individually configured for each

symbology.

• Programmable Length Code

• Programmable Prefix Code

• Programmable Postfix Code

• Character Substitution

• Data Editing: Data can be reorganized according to user programmable formats.

Up to three data editing formats are supported.

• Extremely Low Power Consumption



 

The WWS800 kit contains:

WWS800 Cordless Barcode Scanner

WWS800 Base/Charger dock

Keyboard wedge or USB cable (depending on configuration ordered)

Power Supply for Base/Charger dock

CD containing this manual

Note : For installation and configuration instructions on

Bluetooth Serial Port operation, please refer to the section

“Bluetooth Serial Port”.

   

Keyboard Wedge connection USB connection

Connect the interface cable into the 15-pin connector at the back of the base. The

cable you connect will depend on the interface you ordered. The configurations

shown are the Keyboard Wedge and the USB cable connections.

IMPORTANT: First turn OFF your PC or Laptop that you are connecting the base

cable to. Connect the cable to the base and then plug the other end of the cable into

the appropriate connection on your PC as shown in the figures above.

Connect 5VDC jack of the power supply cable into the DC 5V port located at the

back of the base. Connect the AC plug to an AC outlet and then turn ON your PC.

You are now ready to configure your scanner and base.

Specyfikacje produktu

Marka:	Wasp
Kategoria:	czytnik kodów kreskowych
Model:	WWS800

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Wasp WWS800, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą

Twoje imię*

Twój email*

Napisz tutaj swoje pytanie

Instrukcje czytnik kodów kreskowych Wasp

Wasp WDI9600 Instrukcja

7 Października 2024

Wasp WLS9500 Instrukcja

7 Października 2024

Wasp WCS3900 Instrukcja

7 Października 2024

Wasp WDI4600 Instrukcja

7 Października 2024

Wasp WLR8900 Instrukcja

7 Października 2024

Wasp WCS3905 Instrukcja

7 Października 2024

Wasp WLS8600 Instrukcja

7 Października 2024

Wasp WWS800 Instrukcja

7 Października 2024

Wasp WWS750 Instrukcja

7 Października 2024

Wasp WLR8950 Instrukcja

7 Października 2024

Instrukcje czytnik kodów kreskowych

Najnowsze instrukcje dla czytnik kodów kreskowych

Posiflex CD-3602U Instrukcja

9 Października 2024

Posiflex CD-3202U Instrukcja

9 Października 2024

Datalogic CBX500 Instrukcja

9 Października 2024

Brady IRX200 Instrukcja

8 Października 2024

Newland HR33 Marlin filaire Instrukcja

8 Października 2024

Manhattan 154116 Instrukcja

7 Października 2024

Datalogic QuickScan L QD2300 Instrukcja

5 Października 2024

Datamax O'Neil Hyperion 1300g Instrukcja

4 Października 2024

Bluebird EF401 Instrukcja

4 Października 2024

Qian QLLA1701 Instrukcja

4 Października 2024