Instrukcja obsługi Vtech RM2751

Vtech Elektroniczna niania RM2751

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Vtech RM2751 (2 stron) w kategorii Elektroniczna niania. Ta instrukcja była pomocna dla 4 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/2

Frequency Baby unit: 2412 - 2462 MHz

Channels 11

LCD 2.8’’ Color LCD

(IPS 320x240 pixels)

Nominal effective range Maximum power allowed by FCC and IC. Actual operating range may

vary according to environmental conditions at the time of use.

Power requirement Parent unit/Baby unit power adapters:

VTech, VT05EUS05100

Rated output: 5V DC, 1000mA.

Parent unit battery: 3.6V 2600mAh, 9.36Wh Lithium-ion battery

Specifications are subject to change without notice.

Technical specications

Android TM and Google Play TM are trademarks of Google Inc.

App Store is a trademark of Apple Inc., registered in the U.S. and other countries.

IOS is a trademark or registered trademark of Cisco in the U.S. and other countries and is used under license.

RM2751

2.8 inch Smart Wi-Fi 1080p

Video Monitor

What does Video Monitor do?

VTech 2.8 inch Smart Wi-Fi 1080p Video Monitor allows you to stay close to your baby when

you are on the move or away.

This monitor is Wi-Fi enabled, which uses your home wireless network to stream live video and

audio through the baby unit and 2.8 inch color screen parent unit. It allows you to maintain a

constant connection to your baby.

You can also monitor from your smartphone and mobile tablet.

VTech 2.8 inch Smart Wi-Fi 1080p Video Monitor uses MyVTech Baby Pro app to let you

instantly see and hear what’s happening with your baby from anywhere in the world.

The app can be downloaded from the App Store or the Google PlayTM Store, directly from your

smartphone or mobile tablet.

Quick start guide

(Canada version)

For more support information

UL STD.

62368-1

CERTIFIED TO

CSA STD.

C22.2 NO.62368-1

CO ORMS TO NF

Direct mode

The parent unit and the baby unit of your video monitor connect to each others in Direct mode

by default, which allows you to stream live video right out of the box. Direct mode connection

lets you stream live video from parent unit only.

• You may experience reduced signal strength if your parent unit and baby unit are far apart, or there are

obstructing factors, such as internal walls, between them. Move the parent unit closer to the baby unit to

improve the signal strength. You can also set up Router mode to connect via your home Wi-Fi network to

improve the connection between your parent unit and baby unit.

Router mode

You can continue using your video monitor

with connection, or you Direct mode

can set up your monitor in Router mode

connection.

Router mode uses your home Wi-Fi

network to connect your video monitor.

It supports streaming live video through

parent unit and smartphone app.

We recommend that you set up your

monitor in Router mode to enjoy streaming

live video via your parent unit with better

connection.

If you want to stream live video remotely with your mobile device, download and install the

MyVTech Baby Pro mobile app. With the mobile app, your Wi-Fi router (not included) provides

Internet connectivity to your video monitor system. It serves as a communicating channel

between your baby unit and mobile device, allowing you to monitor and/or control your baby

unit wherever you are. For detail, see Download app for mobile access section in this quick start

guide.

Notes

• Your parent unit detects the connection signal strength. If you have connected your video monitor with

your home Wi-Fi network, your parent unit automatically switches to direct or router mode - the one that

has stronger signal strength.

• When both parent unit and app are viewing the camera simultaneously, the video quality will be

optimised to deliver the best possible viewing result.

What’s in the box

Connect, charge and power on the baby monitor

x 2 x 2

Quick start guide

Your video monitor package contains the following items. Save your sales receipt and original

packaging in the event warranty service is necessary.

How the system works

For mobile access:

MyVTech Baby Pro mobile app

Network Wi-Fi

Wi-Fi router 2.4GHz 802.11 b/g/n

Internet connection 1.5 Mbps @ 720p or 2.5 Mbps @1080p upload

bandwidth per baby unit

Requirements

Connect the baby monitor

Fully insert the provided power adapters into the parent unit and baby unit power jack, then plug

into a power source. You can hear a clicking sound if it plugs correctly, and the battery LED light on the

parent unit turns on.

Notes

• The rechargeable battery in the parent unit is built-in.

• Use only the power adapters supplied with this product.

• Make sure the parent unit and the baby unit are not connected to an electronically controlled electric

outlet.

• Connect the power adapters in a vertical or ﬂoor mount position only. The adapter prongs are not

designed to hold the weight of the parent unit and the baby unit, so do not connect them to any ceiling,

under-the-table, or cabinet outlets. Otherwise, the adapters may not properly connect to the outlets.

• Make sure the parent unit, the baby unit and the power adapter cords are out of reach of children.

• To maintain compliance with the FCC’s RF exposure guidelines, place the baby unit at least 20cm from

nearby persons.

Charge the parent unit battery before use

The parent unit runs on an internal rechargeable battery or AC power. To continuously monitor

your baby, keep the parent unit connected to AC power. With the battery alone, the parent unit

can cordlessly run for a short time only.

Notes

• Before using the baby monitor for the ﬁrst time, charge the parent unit battery for 12 hours. When the

parent unit battery is fully charged, the battery icon becomes solid .

• The standby time varies depending on your actual use.

The battery icon indicates the battery status (see the following table).

Battery indicators Battery status Action

alert displays on the parent

unit screen, the battery icon

becomes empty , with the

LED light ﬂashes.

The battery has very little

charge and may be used

for only a short time.

Charge

without interruption

(about 30 minutes).

The battery icon becomes solid

The battery is fully

charged.

To keep the battery charged,

connect it to AC power.

The parent unit turns on automatically after

it connects to the power socket, and the

welcome screen appears. You can press and

hold to turn it on or off.

NOTE:

Camera lens and surface may get

warm during normal operation.

WARM

Parent unit overview

Local access

Mobile access Enhanced local access

Press and hold

The applied nameplate is located at the bottom of the baby unit’s base.

When using your equipment, basic safety precautions should

always be followed to reduce the risk of ﬁre, electric shock and

injury, including the following:

1. Follow all warnings and instructions marked on the product.

2. Adult setup is required.

3. CAUTION: Do not install the baby unit at a height above 6.5

feet (2 meters).

4. This product is intended as an aid. It is not a substitute for

responsible and proper adult supervision and should not be

used as such.

5. This product is not intended for use as a medical monitor.

6. Do not use this product near water, for example, near to a

bath, sink, swimming pool or shower.

7. CAUTION: Use only the battery provided. There may be a risk

of explosion if a wrong type of battery is used for the parent

unit. The battery cannot be subjected to high or low extreme

temperature and low air pressure at high altitude during

use, storage or transportation. Disposal of battery in ﬁre or

a hot oven, mechanically crushing or cutting the battery can

result in an explosion. Leaving the battery in an extremely

high temperature surrounding environment can result in an

explosion or the leakage of ﬂammable liquid of gas. Battery

subjected to extremely low air pressure may result in an

explosion or the leakage of ﬂammable liquid or gas. Dispose

of used battery according to the information in The RBRC seal.

8. Use only the adapters included with this product. Incorrect

adapter polarity or voltage can seriously damage the product.

Power adapter information:

Baby Unit Output: 5V DC 1A

VTech Telecommunications Ltd.

Model: VT05EUS05100

Parent Unit Output: 5V DC 1A

VTech Telecommunications Ltd.

Model: VT05EUS05100

Rechargeable battery information:

Zhuhai Great Power Energy Co., Ltd.

Li-ion battery, 3.6V, 2600mAh, 9.36Wh;

Model:

ICR18650-2.6Ah-3.6V-1S1P

9. The power adapter is intended to be correctly oriented in a

vertical or ﬂoor mount position. The prongs are not designed

to hold the plug in place if it is plugged into a ceiling, under-

the-table or cabinet outlet.

10. For pluggable equipment, the socket-outlet (power adapter)

should be installed near the equipment and should be easily

accessible.

11. Unplug this product from the wall outlet before cleaning.

Do not use liquid or aerosol cleaners. Use a damp cloth for

cleaning.

12. Do not modify the power adapters or replace with other

power adapters, as this causes a hazardous situation.

13. Do not allow anything to rest on the power cords. Do not install

this product where the cords may be walked on or crimped.

14. This product should be operated only from the type of power

source indicated on the marking label. If you are not sure of

the type of power supply in your home, consult your dealer or

electricity supply provider.

15. Do not overload wall outlets or use an extension cord.

16. Do not place this product on an unstable table, shelf, stand or

other unstable surfaces.

17. This product should not be placed in any area where proper

ventilation is not provided. Slots and openings in the back or

bottom of this product are provided for ventilation. To protect

them from overheating, these openings must not be blocked

by placing the product on a soft surface such as a bed, sofa

or rug. This product should never be placed near or over a

radiator or heat source.

18. Never push objects of any kind into this product through

the slots because they may touch dangerous voltage points

or create a short circuit. Never spill liquid of any kind on the

product.

19. To reduce the risk of electric shock, do not disassemble

this product, but take it to an authorized service facility.

Disassembling or removing parts of the product other than

via the battery door may expose you to dangerous voltages

or other risks. Incorrect reassembling can cause electric shock

when the product is subsequently used.

20. You should test the sound reception every time you turn on

the units or move one of the components.

21. Periodically examine all components for damage.

22. There is a very low risk of privacy loss when using certain

electronic devices, such as baby monitors, cordless

telephones, etc. To protect your privacy, make sure the

product has never been used before purchase, reset the baby

monitor periodically by powering off and then powering

on the units, and power off the baby monitor if you are not

intending to use it for some time.

23. Children should be supervised to ensure that they do not play

with the product.

24. The small parts of this monitor can be swallowed by babies or

small children. Keep these parts out of reach of children.

25. The product is not intended for use by persons (including

children) with reduced physical, sensory or mental capabilities,

or lack of experience and knowledge, unless they have

been given supervision or instruction concerning use of the

appliance by a person responsible for their safety.

SAVE THESE INSTRUCTIONS

Cautions

• Use and store the product at a temperature between 32 oF

(0oC) and 104oF (40oC).

• Batteries should not be exposed to excessive heat such as

bright sunshine or ﬁre.

• Mishandling batteries can cause burn, ﬁre or explosion

hazards.

• Do not expose the product to extreme cold, heat or direct

sunlight. Do not put the product close to a heating source.

• Strangulation Hazard—Children have STRANGLED

in cords. Keep this cord out of the reach of children

(more than 3 ft (0.9m) away). Do not remove

warning label on the adapter cord.

• Never place the baby unit(s) inside the baby’s

crib or playpen. Never cover the baby unit(s) or

parent unit with anything such as a towel or a blanket.

• Other electronic products may cause interference with your

baby unit. Try installing your baby unit as far away from these

electronic devices as possible: wireless routers, radios, cellular

telephones, intercoms, room monitors, televisions, personal

computers, kitchen appliances and cordless telephones.

Precautions for users of implanted cardiac pacemakers

Cardiac pacemakers (applies only to digital cordless devices):

Wireless Technology Research, LLC (WTR), an independent

research entity, led a multidisciplinary evaluation of the

interference between portable wireless devices and implanted

cardiac pacemakers. Supported by the U.S. Food and Drug

Administration, WTR recommends to physicians that:

Pacemaker patients

• Should keep wireless devices at least six inches from the

pacemaker.

• Should NOT place wireless devices directly over the

pacemaker, such as in a breast pocket, when it is turned ON.

WTR’s evaluation did not identify any risk to bystanders with

pacemakers from other persons using wireless devices.

Electromagnetic elds (EMF)

This VTech product complies with all standards regarding

electromagnetic ﬁelds (EMF). If handled properly and according

to the instructions in this user’s manual, the product is safe to be

used based on scientiﬁc evidence available today.

Important safety instructions

Basic operation

Talk to your baby via the baby unit

1. Press and hold the key.

2. icon displays on When the

screen, speak to your parent unit.

Your voice is transmitted to the

baby unit.

3. When ﬁnished talking, release

the key and hear your baby

again.

Adjust speaker volume

Press to adjust your parent or

unit speaker volume level received from

the baby unit.

After powering up your video monitor, the parent unit streams live video in direct mode.

We recommend you follow the instructions on screen to set up home Wi-Fi network

with your monitor for functionality enhancements and mobile access. See Auto software

and rmware update and Download app for mobile access in this quick start guide.

Use the menu

Press on the parent unit to enter the

main menu, choose a menu item, or

save a setting. You can use the parent

unit menu for advanced settings or

operations, such as to play or stop

lullaby, or adjust the motion and sound

detection settings.

While in the menu:

• Press or to scroll among the

menu options.

• Press to select an item.

• Press to return.

• Press to exit the menu.

To restore to the default settings or reset the

Wi-Fi connection, you can reset the parent

unit by pressing the key at the back of RESET

the unit.

Use a pin and insert it into the hole on the

back of the parent unit, and then gently press

the button inside.

Turn on/off the parent unit screen

You can turn on or off the parent unit screen

without powering off the parent unit. You

can still hear sound from the baby unit.

• Press on the parent unit to turn off

the screen.

• Press any keys on the parent unit to turn

on the screen again.

Muted

Press and hold

Press

Protect your privacy and online security

VTech cares about your privacy and peace of mind. That’s why we’ve put together a list of

industry-recommended best practices to help keep your wireless connection private and

your devices protected when online. We recommend you carefully review and consider

complying with the following tips.

Ensure your wireless connection is secure.

• Before installing a device, ensure your router’s wireless signal is encrypted by selecting

the “WPA2-PSK with AES” setting in your router’s wireless security menu.

Change default settings.

• Change your wireless router’s default wireless network name (SSID) to something unique.

• Change default passwords to unique, strong passwords. A strong password:

- Is at least 10 characters long.

- Is complex.

- Does not contain dictionary words or personal information.

- Contains a mix of uppercase letters, lowercase letters, special characters and numbers.

Keep your devices up to date.

• Download security patches from manufacturers as soon as they become available. This

will ensure you always have the latest security updates.

• If the feature is available, enable automatic updates for future releases.

Disable Universal Plug and Play (UPnP) on your router.

• UPnP enabled on a router can limit the effectiveness of your ﬁrewall by allowing other

network devices to open inbound ports without any intervention or approval from you.

A virus or other malware program could use this function to compromise security for the

entire network.

For more information on wireless connections and protecting your data, please review the

following resources from industry experts:

1. Federal Communications Commission: Wireless Connections and Bluetooth Security Tips

–

www.fcc.gov/consumers/guides/how-protect-yourself-online.

2. U.S. Department of Homeland Security: Before You Connect a New Computer to the

Internet –

www.us-cert.gov/ncas/tips/ST15-003.

3. Federal Trade Commission: Using IP Cameras Safely –

https://www.consumer.ftc.gov/articles/0382-using-ip-cameras-safely.

4. Wi-Fi Alliance: Discover Wi-Fi Security –

http://www.wi-ﬁ.org/discover-wi-ﬁ/security.

Overview

Baby unit overview

1Light sensor

2Camera lens

3Infrared LEDs

Allow you to see clearly in a dark surrounding.

4Microphone

5 Night light touch key

(for model with Serial Number starts

with 0KW)

• Tap to turn the night light on or off.

• Tap and hold to adjust night light

brightness.

6Night light

7Speaker

8 Night light control key

• Press to turn the night light on or off.

• Press and hold to adjust night light

brightness.

9PAIR

• The parent unit and baby unit(s) provided

are already paired.

• Reset the baby unit to factory default.

Press and hold PAIR key and Night light

control key at the same time, until you

hear a beep sound.

10 Power jack

11 Temperature sensor

12 Slots for wall mounting

• Wall mount bracket is included in your

package.

13 Product label

• Here show the product Serial Number

(S/N) and other speciﬁcation. If the serial

number starts with 0KW, the product

comes with a night light touch key

feature.

WIFI M AC: XXXXXX

Mad e in China

For produ ct su pport ple as e

cal l: 1300 369 193

Mo del :RM275 -2 BU

S/N: XXXXXXXXXXX

Go to www.vtechcanada.com

for the latest VTech product news.

Str ang ul atio n

Haz a rd

Keep this cord out of reach of children.

The cord ne eds to be at lea s t thre e feet

away from t he child at all tim es . Do not

use with an e xtens ion cord. Do not

rem ove t his t ag.

Éloignez ce cordon des en fants. Le

cordon doit s e tro uve r à a u moins trois pieds d’un enfant e t ce, en tou t te mps .

N’utilisez pa s de ra llonge. Ne re tirez pa s cette é tiquett e.

Manten ga e st e cable fuera de la alcan ce

de los niños . Este cable deb e es ta r por

lo meno s t res pies fuer a de la alcance

del niño en to do m ome nto. No lo us e

con una exte ns ión inalá mbr ica. No quite es ta e tiquet a.

Ri s q u e

d’é tr an g le men t

Ri e sg o de

e str a n gu la ci ó n

Str ang ul atio n

Haz a rd

Keep th is cord out of reach of children.

The cord ne eds to be at lea s t thre e feet

away from t he child at all tim es . Do not

use with an e xtens ion cord. Do not

rem ove t his t ag.

Éloignez ce cordon des en fants. Le

cordon doit s e tro uve r à a u moins trois

pieds d’un enfant e t ce, en tou t te mps .

N’utilisez pa s de ra llonge. Ne re tirez pa s cette é tiquett e.

Manten ga e st e cable fuera de la alcan ce

de los niños . Este cable deb e es ta r por

lo meno s t res pies fuer a de la alcance

del niño en to do m ome nto. No lo us e

con una exte ns ión inalá mbr ica. No quite

es ta e tiquet a.

Ri s q u e

d’é tr an g le men t

Ri e sg o de

e str a n gu la ci ó n

1 / Menu/Select

• Press to enter the main menu.

• While in a menu, press to choose an

item, or save a setting.

/ Talk/Return

• Press and hold to talk to the baby unit.

• While in a submenu, press to go back.

3 / Power / LCD on/off / Exit

• Press and hold to power on/off the

parent unit.

• Press to screen on/off.

• While in a submenu, press to exit.

4 / / /

• Increase or decrease parent unit’s

volume.

• While in a submenu, press to navigate

leftward or rightward.

5Microphone

6 LED light

• On when the parent unit is connected

to AC power, and the battery is

charging.

• Flashes when the parent unit battery is

low and needs charging.

7LINK LED light

• On when the parent unit is linked to

the baby unit.

• Flashes when the link to the baby unit

is lost.

8Antenna

9Power jack

10 RESET

• Force reboot the parent unit.

11 Speaker

Raise the parent unit

antenna for better

reception.

mount the baby unit (optional)

1. Place the wall mount bracket on a

wall and then use a pencil to mark

two holes in parallel. Remove the

wall mount bracket and drill two

holes in the wall (7/32 inch drill bit).

Notes

• Check for reception strength and

camera angle of the baby unit before

drilling the holes.

• The types of screws and wall plugs you

need depend on the composition of

the wall. You may need to purchase

the screws and wall plugs separately to

mount your baby units.

2. If you drill the holes into a stud, go

to step 3.

• If you drill the holes into an

object other than a stud, insert

the wall plugs into the holes.

Tap gently on the ends with a

hammer until the wall plugs are

ﬂush with the wall.

3. Align the wall mount bracket and screws with

the holes in the wall as shown. Tighten the screw

in the middle hole ﬁrst, so that the wall mount

bracket position is ﬁxed. You can tighten the

other screw in the top hole.

3. Insert the screws into the holes and

tighten the screws until only 1/4 inch of

the screws are exposed.

4. Place the baby unit on the wall

mount bracket, and then slide it

forward until it locks into place. Align

the holes on the wall mount bracket

with the screws on the wall, and slide

the wall mount bracket down until it

locks into place.

4. Place the baby unit on the wall mount bracket,

and then slide it forward until it locks into place.

Connect the power adapter to the baby unit.

Download app for mobile access

Test the sound level and position the video monitor

Auto software and rmware update

Note

• This video monitor is intended as an aid. It is not a substitute for proper adult supervision, and should not

be used as such.

Testing the sound level of the video monitor

• For hearing protection, make sure the parent unit is more than 3 ft (1m) away from the baby

unit. If you hear any feeback noise from the parent unit, move the parent unit further until the

noise stops. You can also press on the parent unit to lower or mute the noise.

• Increase the parent unit speaker volume if you cannot hear the sounds transmitted from the baby unit.

Positioning the monitorvideo

• Keep the baby unit out of the reach of your baby. Never

place or mount the baby unit inside the baby’s crib or

playpen.

1. Place the baby unit more than 3 ft (1 m) away

from your baby.

2. Adjust the angle of the baby unit to aim at your baby.

3. To avoid causing feedback noise from your video monitor:

• Make sure your baby unit and parent unit are more than 3 ft (1m) apart; OR

• Turn down the volume of your parent unit.

>3ft (1 m)

3ft (1m)

To ensure that your video monitor is always at its best performance, the parent unit will

prompt a message and ask you to update its software and the baby unit's ﬁrmware

when there are new versions available.

• Follow the instructions on the parent unit screen to update your video monitor. If you

skip the updates, the parent unit and baby unit will be updated automatically when

the parent unit is powered off, and then powered on again.

• To check if your device is running on the latest software, p ress when the parent unit

is idle, go to: > > .

Connect your video monitor with home Wi-Fi network

• You must connect your video monitor to your secured home Wi-Fi network in order

to receive the latest software and ﬁrmware updates. To set Wi-Fi up, go to:

> /

b) From app store

1. Browse the App Store or the Google Play store .

2. Search for the mobile app with the keyword “myvtech baby pro“.

3. Download and install the MyVTech Baby Pro mobile app to your mobile device.

Scan the QR codes on the right to get the app.

• Make sure your mobile device meets the minimum

requirement for the mobile app.

Minimum requirement

The mobile app is compatible with:

• AndroidTM 6.0 or later; and

• iOS 12 or later.

Set up user account

In your mobile device:

1. to run the mobile app in your mobile device, and then create a user Tap

account.

2. We recommend that you use common webmail services, such as Google Gmail

for registration of your user account. Check your email (and Spam folder), and

activate your new camera account via the email link, then sign in to your account.

If you plan to install your baby unit in a designated

location, and use your home Wi-Fi network to

connect your video monitor, you need to test

which of your selected monitoring areas within the

house have good Wi-Fi signal strength. After you

have powered on your parent unit, you can use

your parent unit’s Wi-Fi signal strength indicator

to assist in checking. Once you have identiﬁed the

suitable location, you can install your baby unit.

Adjust the distance between your baby unit and

the Wi-Fi router if needed.

• Depending on surroundings and obstructing

factors, such as the effect distance and internal

walls have on signal strength, you may experience

reduced Wi-Fi signal. To improve the Wi-Fi signal

strength, adjust the distance or direction of your

parent unit. Check with your parent unit again.

test the location for the baby unit

To keep this product working well and looking good, follow these guidelines:

• Avoid placing it near heating appliances and devices that generate electrical noise (for example, motors or

ﬂuorescent lamps).

• DO NOT expose it to direct sunlight or moisture.

• Avoid dropping the product or treating it roughly.

• Clean with a soft damp cloth.

• DO NOT immerse the parent unit and the baby unit in water and do not clean them under running water.

• DO NOT use cleaning spray or liquid cleaners.

• Make sure the baby unit and parent unit are dry before you connect them to the mains again.

General product care

When you are not going to use the baby monitor for some time, store the parent unit, the baby unit and the

adapters in a cool, dry place.

Storage

Adult supervision

• This baby monitor should be for use by adults only.

• Do not place the baby unit inside the crib or playpen.

• To ensure your children’s safety, do not allow them to touch or play with the baby monitor and its

accessories. THIS IS NOT A TOY.

Parent unit icons

CABLE MANAGEMENT

1 2 3

What does this limited warranty cover?

The manufacturer of this VTech Product warrants to the

holder of a valid proof of purchase (“Consumer” or “you”)

that the Product and all accessories provided in the sales

package (“Product”) are free from defects in material

and workmanship, pursuant to the following terms and

conditions, when installed and used normally and in

accordance with the Product operating instructions. This

limited warranty extends only to the Consumer for Products

purchased and used in the United States of America and

Canada.

What will VTech do if the Product is not free from defects

in materials and workmanship during the limited warranty

period (“Materially Defective Product”)?

During the limited warranty period, VTech’s authorized service

representative will replace at VTech’s option, without charge,

a Materially Defective Product. If we choose to replace

the Product, we may replace it with a new or refurbished

Product of the same or similar design. We will retain

defective parts, modules, or equipment. Replacement of the

Product, at VTech’s option, is your exclusive remedy. VTech

will return the replacement Products to you in working

condition. You should expect the replacement to take

approximately 30 days.

How long is the limited warranty period?

The limited warranty period for the Product extends for ONE

(1) YEAR from the date of purchase (90 days on products

purchased as Refurbished*). This limited warranty also

applies to the replacement Product for a period of either (a)

90 days from the date the replacement Product is shipped

to you or (b) the time remaining on the original one-year

warranty (90-day limited warranty on products that are

purchased as Refurbished*); whichever is longer.

*Refurbished products purchased from our online store

carry a 90-day replacement warranty.

What is not covered by this limited warranty?

This limited warranty does not cover:

1. Product that has been subjected to misuse, accident,

shipping or other physical damage, improper installation,

abnormal operation or handling, neglect, inundation,

ﬁre, water or other liquid intrusion; or

2. Product that has been damaged due to repair, alteration

or modiﬁcation by anyone other than an authorized

service representative of VTech; or

3. Product to the extent that the problem experienced is

caused by signal conditions, network reliability, or cable or

antenna systems; or

4. Product to the extent that the problem is caused by use

with non-VTech accessories; or

5. Product whose warranty/quality stickers, product serial

number plates or electronic serial numbers have been

removed, altered or rendered illegible; or

6. Product purchased, used, serviced, or shipped for repair

from outside the United States of America or Canada, or

used for commercial or institutional purposes (including

but not limited to Products used for rental purposes); or

7. Product returned without a valid proof of purchase (see

item 2 below); or

8. Charges for installation or set up, adjustment of customer

controls, and installation or repair of systems outside the

unit.

How do you get warranty service?

To obtain warranty service in the USA, please visit our

website at www.vtechphones.com or call 1 (800) 595-9511.

In Canada, go to www.vtechcanada.com or call

1 (800) 267-7377.

NOTE: Before calling for service, please review the user’s

manual - a check of the Product’s controls and features may

save you a service call.

Except as provided by applicable law, you assume the risk

of loss or damage during transit and transportation and are

responsible for delivery or handling charges incurred in the

transport of the Product(s) to the service location. VTech

will return replaced Product under this limited warranty.

Transportation, delivery or handling charges are prepaid.

VTech assumes no risk for damage or loss of the Product in

transit.

What must you return with the Product to get warranty

service?

1. Return the entire original package and contents including

the Product to the VTech service location along with a

description of the malfunction or difﬁculty; and

2. Include a “valid proof of purchase” (sales receipt)

identifying the Product purchased (Product model) and

the date of purchase or receipt; and

3. Provide your name, complete and correct mailing

address, and telephone number.

Other limitations

This warranty is the complete and exclusive agreement

between you and VTech. It supersedes all other written or

oral communications related to this Product. VTech provides

no other warranties for this Product. The warranty exclusively

describes all of VTech’s responsibilities regarding the

Product. There are no other express warranties. No one is

authorized to make modiﬁcations to this limited warranty and

you should not rely on any such modiﬁcation. State/Provincial

Law Rights: This warranty gives you speciﬁc legal rights, and

you may also have other rights, which vary from state to state

or province to province.

Limitations: Implied warranties, including those of ﬁtness

for a particular purpose and merchantability (an unwritten

warranty that the Product is ﬁt for ordinary use) are limited

to one year from the date of purchase. Some states/

provinces do not allow limitations on how long an implied

warranty lasts, so the above limitation may not apply to you.

In no event shall VTech be liable for any indirect, special,

incidental, consequential, or similar damages (including,

but not limited to lost proﬁts or revenue, inability to use

the Product or other associated equipment, the cost of

substitute equipment, and claims by third parties) resulting

from the use of this Product. Some states/provinces

do not allow the exclusion or limitation of incidental or

consequential damages, so the above limitation or exclusion

may not apply to you.

Please retain your original sales receipt as proof

of purchase.

Limited warranty

FCC and IC regulations

FCC Part 15

NOTE: This equipment has been tested and found to comply with the requirements for a Class B digital device under Part 15 of

the Federal Communications Commission (FCC) rules. These requirements are intended to provide reasonable protection against

harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not

installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is

no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio

or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

WARNING: Changes or modiﬁcations to this equipment not expressly approved by the party responsible for compliance could void

the user’s authority to operate the equipment.

This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause

harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired

operation.

To ensure safety of users, the FCC has established criteria for the amount of radio frequency energy that can be safely absorbed by a

user or bystander according to the intended usage of the product. This product has been tested and found to comply with the FCC

criteria. The baby unit shall be installed and used such that parts of all persons’ body are maintained at a distance of approximately 8 in

(20 cm) or more. The transmitter and antenna of the parent unit shall be held at least 1 in (2.5 cm) from your face.

This Class B digital apparatus complies with Canadian requirement:

CAN ICES-3 (B)/NMB-3(B)

Industry Canada

This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s

licence-exempt RSS(s). Operation is subject to the following two conditions: (1) This device may not cause interference. (2) This device must

accept any interference, including interference that may cause undesired operation of the device.

The term ‘’IC:‘’ before the certiﬁcation/registration number only signiﬁes that the Industry Canada technical speciﬁcations were met.

This product meets the applicable Innovation, Science and Economic Development Canada technical speciﬁcations.

RF radiation exposure statement

The product complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. The baby unit should be

installed and operated with a minimum distance of 8 in (20 cm) between the baby unit and all persons’ body. Use of other accessories

may not ensure compliance with FCC RF exposure guidelines. This equipment complies also with Industry Canada RSS-102 with respect

to Canada’s Health Code 6 for Exposure of Humans to RF Fields.

The RBRC seal on the lithium-ion battery indicates that VTech Communications, Inc. is voluntarily participating in an

industry program to collect and recycle these batteries at the end of their useful lives, when taken out of service within

the United States and Canada. The program provides a convenient alternative to placing used lithium-ion batteries into

the trash or municipal waste, which may be illegal in your area.

VTech’s participation makes it easy for you to drop off the spent product at local retailers participating in the program

or at authorized VTech product service centers. Please call 1 (800) 8 BATTERY® for information on Li-ion battery recycling and disposal

bans/restrictions in your area. VTech’s involvement in this program is part of its commitment to protecting our environment and

conserving natural resources.

The RBRC Seal and 1 (800) 8 BATTERY

® are registered trademarks of Call2recycle, Inc.

The RBRC seal Need help?

For operations and guides to help you use your video monitor, and for the

latest information and support, check out our online help topics and online

FAQs.

Use your smartphone or mobile device to access our online help.

• Go to https://phones.vtechcanada.com/manuals; OR

• Scan the QR code on the right. Launch the camera app or QR code

scanner app on your smartphone or tablet. Hold the device’s camera up

to the QR code and frame it. Tap the notiﬁcation to be redirected to the

online help page.

- If the QR code is not clearly displayed, adjust your camera’s focus by

moving your device closer or further away until it is clear.

• Search for the model - .RM2751 or RM2751-2

You can also call our Customer Support at 1 (800) 267-7377 for help.

a) From parent unit

• Before installing the app, make sure your baby monitor is connected to your home Wi-Fi

network.

1. when the parent unit is idle.Press ,

2. Go to > .

3. Scan the QR code in the parent unit to download the app into your mobile

device.

App installation

Add camera

Follow the instructions in the mobile app to pair the camera. Tap , then Add Camera

in the mobile app to get started.

Main

Menu Options

General settings

• Adjust parent unit screen

brightness.

• Turn the screen off timer on/off,

or set to screen off after 1, 3 or 5

minutes, or auto screen on when

sound detected.

• Set the Sound Sensitivity level for

auto screen on.

• Adjust baby unit’s speaker volume.

• Change temperature format (°C/°F).

• Help information.

• System information.

• Factory reset.

Connection settings

• Change Wi-Fi network.

• Connect mobile phone.

• Reset connection to direct mode.

Main

Menu Options

Monitoring mode (For RM2751-2 only)

• View baby unit 1 or 2 in Single

mode.

• View both baby units in Patrol

mode.

Zoom

• Select from 4 zoom modes.

• Navigate in the zoom image.

Night light

• Turn on/off night light.

• Select from 10 color modes.

• Adjust the brightness level.

• You can also set the timer to turn

off night light after 15, 30 or 60

minutes, or remain on always.

Melodies and soothing sounds

• Play or stop the lullaby.

• Select to play all melodies, or play

one of the ﬁve melodies and ﬁve

soothing sounds.

• You can also set the timer to stop

playing after 15, 30 or 60 minutes,

or play non-stop.

• Adjust the playing volume level.

Alerts settings

• Turn on/off motion detection,

temperature detection lost link,

and low battery alerts.

• Select the motion detection

sensitivity level.

• Select maximum and minimum

temperature for alert range.

• Mute or adjust the alerts sound

level.

Status icons

Direct mode

Parent unit, baby unit 1 and baby unit 2 (For

RM2751-2 only) are connected to each other

directly.

Router mode

Parent unit, baby unit 1 and baby unit 2 are

connected to home Wi-Fi network.

Night vision is turned on.

Motion detection is turned on.

Sound light indicator

Melodies and soothing sounds are turned on.

Night light is turned on.

Auto night light is turned on.

Talkback is turned on.

Parent unit speaker is muted.

Temperature alert is turned on.

Specyfikacje produktu

Marka:	Vtech
Kategoria:	Elektroniczna niania
Model:	RM2751

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Vtech RM2751, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą

Twoje imię*

Twój email*

Napisz tutaj swoje pytanie

Instrukcje Elektroniczna niania Vtech

Vtech RM5754HD Instrukcja

14 Grudnia 2024

Vtech RM2751 Instrukcja

14 Grudnia 2024

Vtech VC2105 Instrukcja

14 Grudnia 2024

Vtech RM5764-2HD Instrukcja

14 Grudnia 2024

Vtech RM5754-2HD Instrukcja

14 Grudnia 2024

Vtech RM9751 Instrukcja

14 Grudnia 2024

Vtech RM5766HD Instrukcja

2 Października 2024

Vtech Clear Sounds Deluxe Instrukcja

2 Października 2024

Vtech Bel & Tel Instrukcja

24 Września 2024

Vtech BM2150 Instrukcja

23 Września 2024

Instrukcje Elektroniczna niania

Najnowsze instrukcje dla Elektroniczna niania

D-Link DCS-825L Instrukcja

22 Grudnia 2024

Alecto DVM-240 BEELD Instrukcja

21 Grudnia 2024

Oricom SC330 Instrukcja

10 Grudnia 2024

Alecto DVM200XL Instrukcja

5 Grudnia 2024

TrueLife NannyCam V24 Pro Instrukcja

9 Października 2024

TrueLife NannyCam H32 Pro Instrukcja

9 Października 2024

Denver ACT-324 Instrukcja

9 Października 2024

Denver DCA-4811 Instrukcja

8 Października 2024

Kogan KABBCMADDCA Instrukcja

7 Października 2024

Kogan KASMBMPT09A Instrukcja

7 Października 2024