Instrukcja obsługi Vtech DS6072

Vtech telefon DS6072

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Vtech DS6072 (4 stron) w kategorii telefon. Ta instrukcja była pomocna dla 25 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/4

Review the caller ID log when the handset

is not in use.

Decrease the listening volume during a

call.

Scroll down while in a menu, or in the

phonebook, caller ID log, call block list or

redial list.

Move the cursor to the left when entering

numbers or names.

18 – CHARGE light

• On when the handset is charging.

Display icons overview

•

Install the battery

Install the battery as shown below.

NOTES

Use only the battery provided.

If the handset will not be used for a long time,

disconnect and remove the battery to prevent

possible leakage.

•

Connect and charge the battery

NOTES

Use only the power adapter supplied with this

product.

Charge the battery provided with or identified for

use with this product only in accordance with the

instructions and limitations specified in this manual.

Connect the charger

Charge the battery

Place the handset in the charger to charge.

Once you have installed the battery, the handset

LCD display indicates the battery status (see the

following table).

NOTES

For best performance, keep the handset in the

telephone base or charger when not in use.

The battery is fully charged after 12 hours of

continuous charging.

If you place the handset in the charger without

plugging in the battery, the screen displays No

battery.

•

Battery

indicators

Battery status Action

The screen

is blank, or

shows Put in

charger and

flashes.

The battery has

no charge or

very little charge.

The handset

cannot be used.

Charge without

interruption

(at least 30

minutes).

The screen

shows Low

battery and

flashes.

The battery has

enough charge

to be used for a

short time.

Charge without

interruption

(at least 30

minutes).

The screen

shows

HANDSET X.

The battery is

charged.

To keep

the battery

charged,

place it in the

telephone base

or charger

when not in

use.

Before use

Add and register a handset

You can add new handsets (purchased DS6072

separately) to your telephone system. DS6771

Your telephone system supports a maximum of

five devices.

Each handset must be registered with the

telephone base before use. When first

purchased, each expansion handset displays To

NOTE

Charge the new handset without interruption for

at least 30 minutes before registering it to the

telephone base.

To register a handset to the telephone

base:

Place the new handset in the telephone base.

•

After about 10 seconds, the handset displays

Registering.... When the registration process

completes, the handset displays and Registered

you hear a beep. The registration process takes

about 90 seconds.

Deregister handsets

If you want to replace a handset or reassign

the designated handset number of a registered

handset, you must deregister all the handsets

and then individually register each handset.

If you want to register a handset to another

telephone base, you must deregister all

handsets, and then register each handset

individually to the desired telephone base.

To deregister all handsets from the

telephone base:

1. Press and hold on the FIND HANDSET

telephone base for about 10 seconds until

the light on the telephone base IN USE

turns on and starts flashing.

2. Immediately press FIND HANDSET again.

You must press while the FIND HANDSET

IN USE IN USE light is still flashing. The

light turns off, and you hear a confirmation

tone.

3. All handsets display To register HS...

and alternately when the ...see manual

deregistration process completes. The

deregistration process takes about 10

seconds.

Operating range

This cordless telephone operates with the

maximum power allowed by the Federal

Communications Commission (FCC). Even

so, this handset and telephone base can

communicate over only a certain distance - which

can vary with the locations of the telephone base

and handset, the weather, and the layout of your

home or office.

When the handset is out of range, the handset

displays Out of range or no pwr at base.

If there is a call while the handset is out of range,

it may not ring, or if it does ring, the call may not

connect well when you press /HOME . Move

closer to the telephone base, and then press

/HOME to answer the call. If the handset

moves out of range during a telephone

conversation, there may be interference. To

improve reception, move closer to the telephone

base.

ECO mode

This power conserving technology reduces

power consumption for optimal battery

performance. The ECO mode activates

automatically whenever the handset is

synchronized with the telephone base.

General product care

Taking care of your telephone

Your cordless telephone contains sophisticated

electronic parts, so it must be treated with care.

Avoid rough treatment

Place the handset down gently. Save the original

packing materials to protect your telephone if you

ever need to ship it.

Avoid water

Your telephone can be damaged if it gets wet.

Do not use the handset outdoors in the rain,

or handle it with wet hands. Do not install the

telephone base near a sink, bathtub or shower.

Electrical storms

Electrical storms can sometimes cause power

surges harmful to electronic equipment. For your

own safety, take caution when using electrical

appliances during storms.

Cleaning your telephone

Your telephone has a durable plastic casing that

should retain its luster for many years. Clean it

only with a dry non-abrasive cloth. Do not use

dampened cloth or cleaning solvents of any kind.

Congratulations

on purchasing your new VTech product. Before

using this telephone, please read

Important safety instructions.

This manual has instructions on how to set up

and register your new handset. For instructions

on using the handset, see the Abridged user’s

manual that came with your telephone base.

You may also view or download the online user’s

manual for a full set of installation and operation

instructions at www.vtechcanada.com.

Parts checklist

Your telephone package contains the following

items. Save your sales receipt and original

packaging in the event warranty service is

necessary.

Charger overview

1 – Charging pole

Handset overview

1 – Handset earpiece

2 – LCD display

3 – MENU/SELECT

• Show the menu.

• While in a menu, press to select an item,

or save an entry or setting.

4 – VOICE

Press to activate the voice-controlled

application on your connected cell

phone.

5 – OFF/CANCEL

Hang up a call.

Silence the ringer temporarily while the

handset is ringing.

Press and hold to erase the missed call

indicator while the phone is not in use.

Press to return to the previous menu; or

press and hold to return to idle mode,

without making changes.

6 –

Press to add a space when entering

names.

7 –

Press repeatedly to show other dialing

options when reviewing a caller ID log

entry.

8 – INT

Press to start an intercom conversation

or transfer a call.

•

9 – Microphone

10 – MUTE/DELETE

Mute the microphone during a call.

Delete digits or characters while using

the dialing keys.

Silence the ringer temporarily while the

handset is ringing.

Delete the displayed entry while

reviewing the phonebook, caller ID log,

call block list or redial list.

11 –

• Make or answer a call using the handset

speakerphone.

• During a call, press to switch between the

speakerphone and the handset.

12 –

• While you have set the dial mode to

pulse and on a call, press to switch to

tone dialing temporarily.

13 –

• Press repeatedly to add or remove 1

in front of the caller ID log entry before

dialing or saving it to the phonebook.

• Press and hold to set or dial your

voicemail number.

14 – /HOME/FLASH

• Make or answer a home call.

• Answer an incoming home call when you

hear a call waiting alert.

15 – /CELL

• Make or answer a cell call.

• Answer an incoming cell call when you

hear a call waiting alert.

16 – REDIAL/PAUSE

• Press repeatedly to review the redial list.

• Press and hold to insert a dialing pause

while entering a number.

17 –

• Review the phonebook when the

handset is not in use.

• Increase the listening volume during a

call.

• Scroll up while in a menu, or in the

phonebook, caller ID log, call block list or

redial list.

• Move the cursor to the right when

entering numbers or names.

•

User’s manual

Telephones identified with this

logo have reduced noise and

interference when used with most

T-coil equipped hearing aids and

cochlear implants. The TIA-1083

Compliant Logo is a trademark of

the Telecommunications Industry

Association. Used under license.

User’s manual

(Canada version)

Compatible with

Hearing Aid T-Coil

TIA-1083

DS6072

DECT 6.0 cordless telephone

Go to

www.vtechcanada.com

for the latest VTech product

news.

The ENERGY STAR®

program (www.energystar.gov)

recognizes and encourages

the use of products that save

energy and help protect our

environment. We are proud

to mark this product with

the ENERGY STAR® label

indicating it meets the latest

energy efficiency guidelines.

DS6771 base Do not place

the handset in

the charger.

DS6771 base

The battery icon flashes when the

battery is low and needs charging.

The battery icon animates when the

battery is charging.

The battery icon becomes solid

when the battery is fully charged.

ECO The ECO mode activates

automatically to reduce power

consumption when the handset is

within range from the telephone

base.

There are new voicemail received

from your telephone service

provider.

On when the home line is in use or

there is an incoming home call.

Flashes when there is an incoming

home waiting call.

There are Bluetooth devices

connected on the cell devices list.

On when the cell line is in use or

there is an incoming cell call.

Flashes when there is an incoming

cell waiting call.

NEW There are new caller ID log entries.

ANS ON The answering system is turned on.

The handset ringer is off.

THIS SIDE UP

If this product is equipped with a corded or

cordless handset, it is hearing aid compatible.

If this product has memory dialing locations,

you may choose to store emergency telephone

numbers (e.g., police, fire, medical) in these

locations. If you do store or test emergency

numbers, please:

Remain on the line and briefly explain the reason

for the call before hanging up.

Perform such activities in off-peak hours, such as

early morning or late evening.

Industry Canada

This device complies with Industry Canada

license-exempt RSS standard(s).

Operation is subject to the following two

conditions: (1) this device may not cause harmful

interference, and (2) this device must accept any

interference received, including interference that

may cause undesired operation.

Privacy of communications may not be ensured

when using this phone.

The term ‘’IC:‘’ before the certification/

registration number only signifies that the

Industry Canada technical specifications were

met.

The Ringer Equivalence Number (REN) for this

terminal equipment is 0.1. The REN indicates

the maximum number of devices allowed to be

connected to a telephone interface. The termination

on an interface may consist of any combination of

devices subject only to the requirement that the

sum of the RENs of all the devices not exceed five.

This product meets the applicable Innovation,

Science, and Economic Development Canada

technical specifications.

Limited warranty

What does this limited warranty cover?

The manufacturer of this VTech Product warrants

to the holder of a valid proof of purchase

(“Consumer” or “you”) that the Product and

all accessories provided in the sales package

(“Product”) are free from defects in material

and workmanship, pursuant to the following

terms and conditions, when installed and used

normally and in accordance with the Product

operating instructions. This limited warranty

extends only to the Consumer for Products

purchased and used in the United States of

America and Canada.

What will VTech do if the Product is not free

from defects in materials and workmanship

during the limited warranty period (“Materially

Defective Product”)?

During the limited warranty period, VTech’s

authorized service representative will repair

or replace at VTech’s option, without charge,

a Materially Defective Product. If we repair

the Product, we may use new or refurbished

replacement parts. If we choose to replace

the Product, we may replace it with a new or

refurbished Product of the same or similar

design. We will retain defective parts, modules, or

equipment. Repair or replacement of the Product,

at VTech’s option, is your exclusive remedy.

VTech will return the repaired or replacement

Products to you in working condition. You

should expect the repair or replacement to take

approximately 30 days.

How long is the limited warranty period?

The limited warranty period for the Product extends

for ONE (1) YEAR from the date of purchase. If

VTech repairs or replaces a Materially Defective

Product under the terms of this limited warranty,

this limited warranty also applies to the repaired

or replacement Product for a period of either

(a) 90 days from the date the repaired or

replacement Product is shipped to you or (b) the

time remaining on the original one-year warranty;

whichever is longer.

What is not covered by this limited warranty?

This limited warranty does not cover:

Product that has been subjected to misuse,

accident, shipping or other physical damage,

improper installation, abnormal operation or

handling, neglect, inundation, fire, water or

other liquid intrusion; or

Product that has been damaged due

to repair, alteration or modification by

anyone other than an authorized service

representative of VTech; or

Product to the extent that the problem

experienced is caused by signal conditions,

network reliability, or cable or antenna

systems; or

Product to the extent that the problem is

caused by use with non-VTech accessories;

Product whose warranty/quality stickers,

product serial number plates or electronic

serial numbers have been removed, altered or

rendered illegible; or

Product purchased, used, serviced, or

shipped for repair from outside the United

States of America or Canada, or used

for commercial or institutional purposes

(including but not limited to Products used for

rental purposes); or

Product returned without a valid proof of

purchase (see item 2 on the next page); or

Charges for installation or set up, adjustment

of customer controls, and installation or repair

of systems outside the unit.

How do you get warranty service?

To obtain warranty service, please visit our

website at or dial www.vtechcanada.com

1 (800) 267-7377.

NOTE: Before calling for service, please review

the user’s manual - a check of the Product’s

controls and features may save you a service call.

Except as provided by applicable law, you

assume the risk of loss or damage during

transit and transportation and are responsible

for delivery or handling charges incurred in the

transport of the Product(s) to the service location.

VTech will return repaired or replaced Product

under this limited warranty. Transportation,

delivery or handling charges are prepaid.

VTech assumes no risk for damage or loss of

the Product in transit. If the Product failure is

not covered by this limited warranty, or proof of

purchase does not meet the terms of this limited

warranty, VTech will notify you and will request

that you authorize the cost of repair prior to any

further repair activity. You must pay for the cost

of repair and return shipping costs for the repair

of Products that are not covered by this limited

warranty.

What must you return with the Product to get

warranty service?

Return the entire original package and

contents including the Product to the VTech

service location along with a description of

the malfunction or difficulty; and

Include a “valid proof of purchase” (sales

receipt) identifying the Product purchased

(Product model) and the date of purchase or

receipt; and

Provide your name, complete and correct

mailing address, and telephone number.

Other limitations

This warranty is the complete and exclusive

agreement between you and VTech.

It supersedes all other written or oral

communications related to this Product. VTech

provides no other warranties for this Product.

The warranty exclusively describes all of VTech’s

responsibilities regarding the Product. There are

no other express warranties. No one is authorized

to make modifications to this limited warranty and

you should not rely on any such modification.

State/Provincial Law Rights: This warranty gives

you specific legal rights, and you may also have

other rights, which vary from state to state or

province to province.

Limitations: Implied warranties, including

those of fitness for a particular purpose and

merchantability (an unwritten warranty that the

Product is fit for ordinary use) are limited to one

year from the date of purchase. Some states/

provinces do not allow limitations on how long

an implied warranty lasts, so the above limitation

may not apply to you. In no event shall VTech

be liable for any indirect, special, incidental,

consequential, or similar damages (including, but

not limited to lost profits or revenue, inability to

use the Product or other associated equipment,

the cost of substitute equipment, and claims

by third parties) resulting from the use of this

Product. Some states/provinces do not allow

the exclusion or limitation of incidental or

consequential damages, so the above limitation

or exclusion may not apply to you.

Please retain your original sales receipt

as proof of purchase.

Technical specifications

Frequency

control

Crystal controlled PLL synthesizer

Transmit

freuency

1921.536-1928.448 MHz

Channels 5

Nominal

effective

range

Maximum power allowed by FCC and

IC. Actual operating range may vary

according to environment conditions

at the time of use.

Power

requirements

Handset: 2.4V Ni-MH battery

Charger: 6V DC @ 400mA

Memory Phonebook:

50 memory locations; up to 30 digits

and 15 characters

Caller ID log:

30 memory locations; up to 24 digits

and 15 characters

Call block: 20 entries

Important safety instructions

When using your telephone equipment, basic

safety precautions should always be followed to

reduce the risk of fire, electric shock and injury,

including the following:

Read and understand all instructions.

Follow all warnings and instructions marked

on the product.

Unplug this product from the wall outlet

before cleaning. Do not use liquid or aerosol

cleaners. Use a damp cloth for cleaning.

Do not use this product near water such as

near a bath tub, wash bowl, kitchen sink,

laundry tub or swimming pool, or in a wet

basement or shower.

Do not place this product on an unstable

table, shelf, stand or other unstable surfaces.

Avoid placing the telephone system in places

with extreme temperature, direct sunlight, or

other electrical devices. Protect your phone

from moisture, dust, corrosive liquids and

fumes.

Slots and openings in the back or bottom

of the telephone base and handset are

provided for ventilation. To protect them

from overheating, these openings must not

be blocked by placing the product on a soft

surface such as a bed, sofa or rug. This

product should never be placed near or

over a radiator or heat register. This product

should not be placed in any area where

proper ventilation is not provided.

This product should be operated only from

the type of power source indicated on the

marking label. If you are not sure of the

type of power supply in your home or office,

consult your dealer or local power company.

Do not allow anything to rest on the power

cord. Do not install this product where the

cord may be walked on.

Never push objects of any kind into this

product through the slots in the telephone

base or handset because they may touch

dangerous voltage points or create a short

circuit. Never spill liquid of any kind on the

product.

To reduce the risk of electric shock, do

not disassemble this product, but take it to

an authorized service facility. Opening or

removing parts of the telephone base or

handset other than specified access doors

may expose you to dangerous voltages

or other risks. Incorrect reassembling can

cause electric shock when the product is

subsequently used.

Do not overload wall outlets and extension

cords.

10.

11.

12.

Unplug this product from the wall outlet and

refer servicing to an authorized service facility

under the following conditions:

When the power supply cord or plug is

damaged or frayed.

If liquid has been spilled onto the product.

If the product has been exposed to rain or

water.

If the product does not operate normally

by following the operating instructions.

Adjust only those controls that are

covered by the operation instructions.

Improper adjustment of other controls

may result in damage and often requires

extensive work by an authorized

technician to restore the product to normal

operation.

If the product has been dropped and the

telephone base and/or handset has been

damaged.

If the product exhibits a distinct change in

performance.

14. Avoid using a telephone (other than cordless)

during an electrical storm. There is a remote

risk of electric shock from lightning.

15. Do not use the telephone to report a gas

leak in the vicinity of the leak. Under certain

circumstances, a spark may be created

when the adapter is plugged into the power

outlet, or when the handset is replaced in its

cradle. This is a common event associated

with the closing of any electrical circuit. The

user should not plug the phone into a power

outlet, and should not put a charged handset

into the cradle, if the phone is located in an

environment containing concentrations of

flammable or flame-supporting gases, unless

there is adequate ventilation. A spark in

such an environment could create a fire or

explosion. Such environments might include:

medical use of oxygen without adequate

ventilation; industrial gases (cleaning

solvents; gasoline vapors; etc.); a leak of

natural gas; etc.

16. Only put the handset of your telephone next

to your ear when it is in normal talk mode.

17. The power adapters are intended to be

correctly oriented in a vertical or floor mount

position. The prongs are not designed to hold

the plug in place if it is plugged into a ceiling,

under-the-table or cabinet outlet.

SAVE THESE INSTRUCTIONS

13.

•

Battery

CAUTION: Use Only Supplied Battery.

Do not dispose of the battery in a fire. Check

with local waste management codes for

special disposal instructions.

Do not open or mutilate the battery. Released

electrolyte is corrosive and may cause burns

or injury to the eyes or skin. The electrolyte

may be toxic if swallowed.

Exercise care in handling batteries in

order not to create a short circuit with

conductive materials.

Charge the battery provided with or identified

for use with this product only in accordance

with the instructions and limitations specified

in this manual.

Precautions for users of implanted cardiac

pacemakers

Cardiac pacemakers (applies only to digital

cordless telephones):

Wireless Technology Research, LLC (WTR),

an independent research entity, led a

multidisciplinary evaluation of the interference

between portable wireless telephones and

implanted cardiac pacemakers. Supported by

the U.S. Food and Drug Administration, WTR

recommends to physicians that:

Pacemaker patients

Should keep wireless telephones at least six

inches from the pacemaker.

Should NOT place wireless telephones directly

over the pacemaker, such as in a breast

pocket, when it is turned ON.

Should use the wireless telephone at the ear

opposite the pacemaker.

WTR’s evaluation did not identify any risk to

bystanders with pacemakers from other persons

using wireless telephones.

About cordless telephones

Privacy: The same features that make a

cordless telephone convenient create some

limitations. Telephone calls are transmitted

between the telephone base and the

cordless handset by radio waves, so there

is a possibility that the cordless telephone

conversations could be intercepted by radio

receiving equipment within range of the

cordless handset. For this reason, you should

not think of cordless telephone conversations

as being as private as those on corded

telephones.

Electrical power: The telephone base of this

cordless telephone must be connected to a

working electrical outlet. The electrical outlet

should not be controlled by a wall switch. Calls

cannot be made from the cordless handset if

the telephone base is unplugged, switched off

or if the electrical power is interrupted.

•

Potential TV interference: Some cordless

telephones operate at frequencies that may

cause interference to televisions and VCRs.

To minimize or prevent such interference, do

not place the telephone base of the cordless

telephone near or on top of a TV or VCR.

If interference is experienced, moving the

cordless telephone farther away from the

TV or VCR often reduces or eliminates the

interference.

Rechargeable batteries: Exercise care in

handling batteries in order not to create a

short circuit with conducting material such

as rings, bracelets, and keys. The battery or

conductor may overheat and cause harm.

Observe proper polarity between the battery

and the battery charger.

Nickel-metal hydride rechargeable

batteries: Dispose of these batteries in a safe

manner. Do not burn or puncture the battery.

Like other batteries of this type, if burned or

punctured, they could release caustic material

which could cause injury.

The RBRC® seal

The RBRC® seal on the nickel-metal hydride

battery indicates that VTech Communications,

Inc. is voluntarily participating in an industry

program to collect and recycle these batteries at

the end of their useful lives, when taken out of

service within the United States and Canada.

The RBRC® program provides a convenient

alternative to placing used nickel-metal hydride

batteries into the trash or municipal waste, which

may be illegal in your area.

VTech’s participation in RBRC

makes it easy

for you to drop off the spent battery at local

retailers participating in the RBRC

program or

at authorized VTech product service centers.

Please call 1 (800) 8 BATTERY

for information

on Ni-MH battery recycling and disposal bans/

restrictions in your area. VTech’s involvement

in this program is part of its commitment to

protecting our environment and conserving natural

resources.

RBRC® and

1 (800) 8 BATTERY

are registered trademarks of

Rechargeable Battery Recycling

Corporation.

•

FCC, ACTA and IC regulations

FCC Part 15

NOTE: This equipment has been tested and

found to comply with the requirements for a

Class B digital device under Part 15 of the

Federal Communications Commission (FCC)

rules. These requirements are intended to

provide reasonable protection against harmful

interference in a residential installation. This

equipment generates, uses and can radiate radio

frequency energy and, if not installed and used

in accordance with the instructions, may cause

harmful interference to radio communications.

However, there is no guarantee that interference

will not occur in a particular installation. If this

equipment does cause harmful interference

to radio or television reception, which can be

determined by turning the equipment off and

on, the user is encouraged to try to correct the

interference by one or more of the following

measures:

Reorient or relocate the receiving antenna.

Increase the separation between the

equipment and receiver.

Connect the equipment into an outlet on a

circuit different from that to which the receiver is

connected.

Consult the dealer or an experienced radio/TV

technician for help.

WARNING: Changes or modifications to this

equipment not expressly approved by the party

responsible for compliance could void the user’s

authority to operate the equipment.

This device complies with Part 15 of the FCC

rules. Operation is subject to the following two

conditions: (1) this device may not cause harmful

interference, and (2) this device must accept

any interference received, including interference

that may cause undesired operation. Privacy of

communications may not be ensured when using

this telephone.

To ensure safety of users, the FCC has

established criteria for the amount of radio

frequency energy that can be safely absorbed

by a user or bystander according to the intended

usage of the product. This product has been

tested and found to comply with the FCC criteria.

The handset may be safely held against the ear

of the user. The telephone base shall be installed

and used such that parts of the user’s body other

than the hands are maintained at a distance of

approximately 20 cm

(8 inches) or more.

This Class B digital apparatus complies with

Canadian requirement:

CAN ICES-3 (B)/NMB-3(B)

•

FCC Part 68 and ACTA

This equipment complies with Part 68 of the FCC

rules and with technical requirements adopted

by the Administrative Council for Terminal

Attachments (ACTA). The label on the back

or bottom of this equipment contains, among

other things, a product identifier in the format

US:AAAEQ##TXXXX. This identifier must be

provided to your telephone service provider upon

request.

The plug and jack used to connect this equipment

to premises wiring and the telephone network must

comply with applicable Part 68 rules and technical

requirements adopted by ACTA. A compliant

telephone cord and modular plug is provided with

this product. It is designed to be connected to a

compatible modular jack that is also compliant. An

RJ11 jack should normally be used for connecting

to a single line and an RJ14 jack for two lines. See

the installation instructions in the user’s manual.

The Ringer Equivalence Number (REN) is used

to determine how many devices you may connect

to your telephone line and still have them ring

when you are called. The REN for this product is

encoded as the 6th and 7th characters following

the US: in the product identifier (e.g., if ## is 03,

the REN is 0.3). In most, but not all areas, the

sum of all RENs should be five (5.0) or less. For

more information, contact your telephone service

provider.

This equipment must not be used with Party

Lines. If you have specially wired alarm dialing

equipment connected to your telephone line,

ensure the connection of this equipment

does not disable your alarm equipment. If you

have questions about what will disable alarm

equipment, consult your telephone service

provider or a qualified installer.

If this equipment is malfunctioning, it must

be unplugged from the modular jack until the

problem has been corrected. Repairs to this

telephone equipment can only be made by the

manufacturer or its authorized agents. For repair

procedures, follow the instructions outlined under

the Limited warranty.

If this equipment is causing harm to the

telephone network, the telephone service

provider may temporarily discontinue your

telephone service. The telephone service

provider is required to notify you before

interrupting service. If advance notice is not

practical, you will be notified as soon as possible.

You will be given the opportunity to correct the

problem and the telephone service provider

is required to inform you of your right to file a

complaint with the FCC. Your telephone service

provider may make changes in its facilities,

equipment, operation, or procedures that could

affect the proper functioning of this product. The

telephone service provider is required to notify

you if such changes are planned.

Specifications are subject to change without notice.

Document order number: 91-010128-010-100

Specyfikacje produktu

Marka:	Vtech
Kategoria:	telefon
Model:	DS6072

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Vtech DS6072, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą

Twoje imię*

Twój email*

Napisz tutaj swoje pytanie

Instrukcje telefon Vtech

Vtech CS5119-16 Instrukcja

2 Października 2024

Vtech DS6101 Instrukcja

2 Października 2024

Vtech CS6419 Instrukcja

15 Września 2024

Vtech DS6071 Instrukcja

11 Września 2024

Vtech VC7151 Instrukcja

3 Września 2024

Vtech CS6419-16 Instrukcja

27 Sierpnia 2024

Vtech TL30100 Instrukcja

3 Lipca 2024

Vtech CS6649-2 Instrukcja

28 Maja 2024

Vtech CS6419-15 Instrukcja

8 Maja 2024

Vtech DS6072 Instrukcja

8 Maja 2024

Instrukcje telefon

Najnowsze instrukcje dla telefon

Profoon PDX-7020 Instrukcja

14 Października 2024

Profoon PDX-100 Instrukcja

14 Października 2024

Uniden XS 1415 Instrukcja

13 Października 2024

Uniden XDECT 6105BTU Instrukcja

10 Października 2024

Yealink MP56 E2 Instrukcja

9 Października 2024

Yealink MP54 E2 Instrukcja

9 Października 2024

Yealink MP58-WH E2 Instrukcja

9 Października 2024

Yealink MP52 E2 Instrukcja

9 Października 2024

VXi D200 Dialpad Instrukcja

9 Października 2024

Lewitt LCT 240 Instrukcja

9 Października 2024