Instrukcja obsługi Vivanco UR 14

Vivanco Zdalne sterowanie UR 14

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Vivanco UR 14 (43 stron) w kategorii Zdalne sterowanie. Ta instrukcja była pomocna dla 6 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/43

UR 14 UNIVERSAL CONTROLLER

Vivanco GmbH, D-22926 Ahrensburg, E-Mail

: hotline@vivanco.de

, Helpline: +49 (0) 4102 231135

(GB) Instructions 2 

(D) Bedienungsanleitung 4 

(F) Notice d’emploi 7 

(E) Instrucciones para el uso 10 

(I) Istruzioni per l’uso 13 

(NL) Gebruiksaanwijzing 16 

(PL) Instrukcja obsługi 19 

(CZ) Návod k obsluze 22 

(P) Manual de instruções 25 

(DK) Betjeningsvejledning 28 

(S) Bruksanvisning 30 

(RUS)

  

 33

(GR) 36   

(SK) Návod na obsluhu 40 

UR 14 UNIVERSAL CONTROLLER

Vivanco GmbH, D-22926 Ahrensburg, E-Mail

: hotline@vivanco.de

, Helpline: +49 (0) 4102 231135

(GB) Instructions

VIVANCO UR 14 remote control for almost

all TV, audio, video and other infrared-

controllable appliances

Inserting the batteries

Open the battery compartment on the

underside of the UR, see Fig.. Then insert 1

new CR 2032 lithium battery. Make sure that

the polarity is correct: the "+" and "-" markings

on the batteries and in the compartment must

match. To check functionality, press the PWR

button. If everything is correct the red lamp

flickers when the button is pressed.

Lithium Battery:

Caution: Danger of explosion if battery is

incorrectly replaced. Replace only with the

same or equivalent type recommended by the

manufacturer. Dispose of used batteries

according to the manufacturer’s instructions.

Adapting to appliances

In order to control your appliances you must

adapt or set the remote control to them. There

are three ways of doing so: direct control code

entry, code search or learn.

Direct control code entry using the

enclosed list

Example: setting to control a Panasonic

television set:

1. The attached list gives, for

example, the Panasonic Code 176.

Please make sure you have selected the

correct list for television sets (TV).

2. To prepare code entry, press the

SET button, keep it pressed and then press the

required appliance button, e.g. TV1*),

additionally until the lamp (LED) lights

constantly.

3. Then press the number buttons

(e.g. 1 7 6) in sequence.

4. Once the numbers have been

entered the lamp goes out and the remote

control is ready to control your appliance.

5. Finally, test the control code setting

by trying to control (in this example) your

television set. If it does not work at all or not

correctly try a different code from the list or the

code search (see below).

To set the remote control for other

appliances, proceed in the same way. Instead

of the TV appliance button, press another

button e.g. VCR, DVB (SAT, DECODER),

DVD).

The letters on the device buttons TV1/TV2*),

CD/AUX1*), DVB1/DVB2*) SAT1/SAT2*),

TV3/TUNER*), CBL, AMP, DVD1/DVD2*) are

for your orientation only. You can set each type

of device under any of the buttons.

*): All *) marked device keys can be assigned

twice so that 14 different devices can be

controlled altogether. If you press a key once

according to these instructions, you can enter a

device code for the first assignment or control

the first device. If you press a device key twice

within 0,5 seconds you can set the key for a

second device, or control a second device by

the key.

You can terminate the mode by pressing any

device button.

Code search

If the brand of your appliance is not in the list

or none of the codes given fits, we recommend

a code search.

Manual code search

1. Switch on the appliance to be

controlled. Program is running.

2. To prepare code search, press the

SET button, keep it pressed and then press the

required appliance button, e.g. TV1*),

additionally until the lamp (LED) lights

constantly.

3. Then point the remote control at the

appliance to be controlled.

4. Briefly press the SET button once.

The lamp (LED) blinks. – Except when

searching for a TV code you can also briefly

press the (Play) button and use the Play

function to help search and press ON/OFF

for testing the next code. Make sure that a

tape, a DVD or a CD is inserted in the tape

deck, player or recorder.

5. Press the ON/OFF (appliance

on/off) button repeatedly for testing the next

code, approx. every 1,5 seconds, until the

appliance, e.g. your TV reacts by power off or

your DVD player, reacts by Play > button. - If

your appliance has switched itself off you must

switch it back on again, e.g. on the appliance

or with the original remote control, to continue

searching. - When your appliance reacts you

can also try out other buttons without

interrupting the search. If some buttons do not

work properly, simply continue searching with

ON/OFF or Play.

6. When your appliance reacts

correctly, press the appliance button, e.g.

TV1*), and end the search. The lamp (LED)

goes out.

- The UR 14 continues with the search at the

point where you interrupted it. . The code last

UR 14 UNIVERSAL CONTROLLER

Vivanco GmbH, D-22926 Ahrensburg, E-Mail

: hotline@vivanco.de

, Helpline: +49 (0) 4102 231135

entered remains stored. The search stops after

approx. 30 seconds of inactivity.

Automatic code search

Your remote control finds the correct settings

almost automatically in seconds:

1. Switch on the appliance to be

controlled. A channel number, for example,

appears in the display of your satellite receiver.

2. To start the code search, press the

required appliance button, e.g. *) briefly. TV1

3. Then press for about 5 SET

seconds until the lamp (LED) starts to blink.

4. Then point the remote control at the

appliance to be controlled while the remote

control emits a different ON/OFF signal every

second.

5. When your appliance reacts, press

SET within 1-2 seconds, to end the search. – If

you ended the search too late, continue to

search using the Manual Code Search (see

above).

6. Finally, test the control code setting

by trying to control, for example, your DVD

appliance. If it does not work correctly, please

try the code search again. The code search

then begins with the next code in the

sequence. - Remember to switch your

appliance, e.g. DVD, back on again if you wish

to continue searching.

Code identification

You can read off the 3-digit codes you have set

at any time:

1. Press the appliance button of the

appliance which code you want to read off, e.g.

TV1.

2. Press the button and 1,2,3, SET

depending on the part of the code you want to

read off. For example, if you press + after SET 1

TV and the code 176 (in this example) has

been set, the lamp blinks once after SET+1 is

released to show that the hundred figure is 1.

All you have to do is count. The ten figure is

indicated after + is released, e.g. it blinks SET 2

7 times for the 7 in 176. The one figure is

indicated after + is released, e.g. it blinks SET 3

6 times for the 6 in 176.

Learning, Programming, of Missing Control

Functions

The LEARN function is used to supplement the

preprogrammed codes. The standard code

may provide most of functions needed, but you

may miss some key functions. Or you didn´t

find any functioning preprogrammed code for a

device. You can capture upto 65 key function

codes, max 40 per device. The last captured

function will overwrite the previous. learnt.

1 For learning of key codes you must use a

functioning orginal remote controller. Please

use fresh batteries for both remote controls.

2 Please point the original´s remote control

transmitter LED towards the receiver LED of

UR 14 (placed on top, same as transmitter

LED). Distance of LEDs between both remotes

shall be approximately 10mm and must be in

straight line of sight. – Sometimes you have to

move the remotes a bit too and fro while

learning, in order to find right positions.

3 Press the LEARN key for about 3

seconds until the LED (lamp) turns on.

4 Within 10 seconds press a device key

(e.g. **) briefly. The LED is flashing one DVD1)

time .

5 Press and release the target key on the

UR 14, that you want to learn (to reprogram)

(e.g. POWER), the LED starts flashing.

6 Press and hold the source key on the

original remote control (e.g. POWER) until the

LED on your UR 14 remote control stops

flashing and changes to on again. That

indicates that a new function code, e.g.

POWER, has been learnt.

7 Repeat steps 4 to 6 to for capturing more

key functions. - If there is a learning(capturing)

problem, the LED blinks 2 times, lights up for

10 seconds. Then repeat steps 4 to 6 for

capturing more keys functions.

8 Press and release key for exit of LEARN

learning mode. – The controller will exit the

learning mode automatically after about 30

seconds of inactivity.

**) Learning is possible for items, which can be

controlled by using device buttons TV1, TV3,

CD, CBL only!

Memory full indication: if the memory is full,

the LED blinks 2 times and then a programmed

key can be overitten or the controller will exit

learnning mode after 10 seconds of idleness.

Reset/deletion of a captured key function

1 Press the key for about 3 LEARN

seconds until the LED (lamp) turns on.

2 Press and hold the device button, e.g.

DVD1, which belongs to the to be deleted key

function. The LED will flash once.

3 Press the key of which the captured

function shall be deleted, e.g. , additionally 3

briefly. The LED will flash once and the learnt

code is deleted.

4 Press and release key for exit of LEARN

deletion mode.

Reset/deletion of all captured key functions

for a device:

1 Press the key for about 3 LEARN

seconds until the LED (lamp) turns on.

Specyfikacje produktu

Marka:	Vivanco
Kategoria:	Zdalne sterowanie
Model:	UR 14

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Vivanco UR 14, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą

Twoje imię*

Twój email*

Napisz tutaj swoje pytanie

Instrukcje Zdalne sterowanie Vivanco

Vivanco vivcontrol 5 se Instrukcja

27 Września 2024

Vivanco UR12NB Instrukcja

27 Września 2024

Vivanco vivcontrol 3 se Instrukcja

27 Września 2024

Vivanco UR 1200 Instrukcja

18 Września 2024

Vivanco 37600 Instrukcja

16 Września 2024

Vivanco Viv.Control 3 Instrukcja

16 Września 2024

Vivanco UR 1250 Instrukcja

15 Września 2024

Vivanco UR ZAP2 Instrukcja

15 Września 2024

Vivanco UR Z2 Instrukcja

14 Września 2024

Vivanco UR 2 Instrukcja

14 Września 2024

Instrukcje Zdalne sterowanie

Najnowsze instrukcje dla Zdalne sterowanie

Panasonic EUR7502XC0EG Instrukcja

15 Stycznia 2025

Delta GT 9000 Instrukcja

15 Stycznia 2025

Eminent EM1041 Instrukcja

15 Stycznia 2025

Sonos Controller for Android-smartphones Instrukcja

15 Stycznia 2025

Sonos Controller voor Mac of pc Instrukcja

14 Stycznia 2025

Sonos Controller for Android Tablets Instrukcja

14 Stycznia 2025

One For All URC 7935 Instrukcja

14 Stycznia 2025

Sonos Controller for iPad Instrukcja

14 Stycznia 2025

Meliconi fully 8 Instrukcja

12 Stycznia 2025

SilverCrest KH 2155 Instrukcja

12 Stycznia 2025