Instrukcja obsługi Ventus W636

Ventus Stacja pogodowa W636

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Ventus W636 (2 stron) w kategorii Stacja pogodowa. Ta instrukcja była pomocna dla 10 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/2

KSPO:1719-10

NIL TE636NL & TS21 MANUAL 2(ENG)

SIZE:W105 X H148(mm)

BY Lai HZ 9/3/11

SLIM WEATHER FORECASTER WITH

RADIO CONTROLLED CLOCK,

PRESSURE DISPLAY AND IN/ OUT

THERMO-HYGROMETER

USER MANUAL

(TE636NL)

INTRODUCTION

Thank you for selecting our slim Weather Forecaster. This device combines precise time

keeping, monitoring and displaying of pressure information and current temperature/ humidity

data from up to three remote locations (additional sensors are required).

In this package, you will ﬁnd:

• One main unit (receiver)

• One single-channel remote sensor (transmitter)

• One user manual

Please keep this manual handy as it contains practical instructions, technical speciﬁcations and

precautions.

INSTALLATION

The communication between the main unit (receiver) and the remote sensor (transmitter) is

wireless, thus simplifying the installation. The remote temperature sensor transmits data to the

main unit, with an operating range of up to 30 meters in opened area.

The remote temperature sensor can be placed indoors or outdoors, depending on the area where

the temperature is intended to be measured. If you intend to measure outdoor conditions, place

the remote sensor outdoors.

NOTE:

• It is critical to power the remote sensor setting up the main unit.BEFORE

• It is critical to power up and communication between the remote sensor and the main unit test

permanently mounting if outside.BEFORE

BEFORE YOU BEGIN

• We recommend using for the remote sensor and the main unit. When the alkaline batteries

temperature falls below freezing point 0°C (32°F), battery voltage levels will be dropped and

this may reduce the transmission range. For optimum performance, we recommend using

lithium batteries.

• Avoid using rechargeable batteries. (Rechargeable batteries cannot maintain correct power

requirements.)

• ALWAYS remote install batteries in the sensor the main unit. before

• Insert batteries before ﬁrst use, matching the polarity in the battery compartment.

• During initial set up, place the remote sensor close to the main unit.

• After reception is established (remote readings will appear on the main unit’s display),

position the remote sensor and the main unit within the eﬀective transmission range of up to

30 meters.

NOTE:

• Avoid pressing any buttons on the main unit before the remote readings are displayed.

• Transmission or reception range may be aﬀected by trees, metal structures, and electronic

appliances, surrounding building materials and how the main unit and transmitter are

positioned.

• Place the remote sensor so that it faces the main unit (receiver), minimizing obstructions

such as doors, walls and furniture.

• Though the remote sensors are weather-resistant, they should be placed away from direct

sunlight, rain or snow. The optimal location for the remote sensor outdoors is under the eaves

on the north side of the building.

REMOTE TEMPERATURE AND HUMIDITY SENSOR

FEATURES

• Remote data transmission to the main unit via 433 MHz frequency

A. BATTERY COMPARTMENT

• Hold two AAA-size batteries

B. WALL-MOUNT RECESSED HOLE

• Mount the remote sensor on the wall

MOUNTING

• The remote sensor can be placed on the ﬂat surface or mounted on the wall in vertical

position.

• Use a screw, rather than a nail, for best mounting of the sensor.

• When mounting the main unit on the wall or vertical surface, fold the table stand back into

the unit.

PLACEMENT

• The remote sensor should be placed under eaves or a similar location with free air circulation

sheltered from direct sunlight and extreme weather.

• Ideally, place the remote sensor over soil, rather than asphalt which would cause false

readings.

• Avoid placing the remote sensor near sources of heat, such as chimneys and heating elements

• Avoid areas that collect heat from the sun and radiate heat, such as metal, brick or concrete

structures, paving, and patios

• The international standard for the valid air temperature measurements is 1.25meters above the

ground

OPERATION

Immediately after batteries are installed, the remote sensor will start transmitting a temperature

and humidity data to the main unit.

A B

MAIN UNIT

FEATURES

TIME

• Precise time and date set via radio controlled time signals (DCF 77) from the central atomic

clock in Frankfurt

• 12 or 24 hour time format

• Manual adjustment of time and date

• Calendar date with month and day in 7 languages English, German, French, Italian, Spanish,

Dutch and Swedish

• Dual crescendo alarms with snooze

• Programmable ice warning alarm

WEATHER

• Weather forecast for the next 12 to 24 hour in seven large icons: sunny, slightly cloudy,

cloudy, rainy, heavy rainy, snowy and heavy snowy.

• User-deﬁned high/low temperature alarm

• Indoor/outdoor temperature and humidity in up to 3 remote locations (additional sensors

required)

• Barometric pressure in imperial or metric units

• Altitude adjustment for pressure compensation

• 24 hour barometric pressure history chart

• Comfort level indicators (Dry, Humid, etc)

FRONT

REAR

A. WEATHER/ PRESSURE window

B. TEMPERATURE/ HUMIDITY window

C. CLOCK window

D. DOWN ( ) button ▼

• Select the next available mode

• Press and hold for 2 seconds to search for wireless signal from remote sensor.

• Decrease parameters.

E. ALARM button

• When time mode has been selected, press once to display the alarm time of weekday alarm

( ), single alarm ( ) and pre-alarm ( ).

• Hold for 2 seconds, set weekday, single or pre-alarm’s alarm time.

• When temperature mode has been selected, press once to display the highest or lowest

temperature alarm’s value.

• Hold for 2 seconds, set the highest or lowest temperature alarm’s value.

• When alarm is on, press once to stop the alarm temporarily.

F. CHANNEL button

• Press to display the outdoor temperature readings of Channels 1, 2 and 3. (additional remote

sensors are required)

• Hold for 2 seconds, enter into the circulation mode and outdoor temperature readings of

Channels 1, 2 and 3 will be displayed automatically in every 5 seconds.

G. MODE button

• When pressure mode has been selected, press once to display the local pressure, altitude and

sea level.

• Press and hold for 2 seconds to set altitude and sea level.

• When time mode has been selected, press once to toggle between time with seconds display

or time with weekday display.

• Press and hold for 2 seconds, set language of the day of the week, year digit, month digit,

date digit, hour format (12/ 24 hours), hour digit and minute digit. (Note: calendar format is

default in month-date display)

• When temperature mode has been selected, press and hold for 2 seconds to toggle the

temperature unit between Celsius or Fahrenheit.

H. UP ( ) button▲

• Press to select the next available mode

• Increase the parameters

• In time with seconds display mode, press and hold for 2 seconds to activate/ deactivate radio

controlled time signal search manually.

I. MEM button

• When temperature mode has been selected, press to recall the minimum or maximum

temperature and humidity readings of main and remote units.

• Press and hold for 2 seconds, collected memories will be cleared.

• When pressure mode has been selected, press once to check the historical pressure data for

the past 24 hours.

J. WALL- MOUNT hole

• A recessed opening to mount the unit on a wall

K. BATTERY COMPARTMENT

• Accommodate two (2) CR2032 batteries

L. TABLE STAND

PLACEMENT

• Make sure that the main unit is locating within the operating range of all remote sensors.

• Ideally the main unit should be placed within line of sight of remote sensors. Avoid

placing the main unit where surfaces emitting and radiating heat (e.g. heating ducts or air

conditioners) and areas with interference from wireless devices (e.g. cordless phones, radio

headsets, baby monitoring devices and other electronics).

OPERATION

Once the main unit is powered, the display will show all available LCD segments for a moment.

IMPORTANT: All of the display functions will be locked, allowing setting your local altitude

and pressure parameters by pressing the UP ( ) DOWN ( ) MODE▲ or ▼ and buttons. The

locked display will show the pressure icon and abbreviation ﬂashing in the “inHg” Weather/

Pressure Window Clock Window, default time in and channel 1’s temperature and humidity

readings in Temperature/ Humidity Window.

If pressure and altitude are not conﬁgured during this time, the unit will self-calibrate in a few

minutes and show the default settings for the pressure and altitude (sea level) and all remote

weather sensors readings.

IFE

17 18

19 20

21 22

GETTING STARTED

WEATHER FORECAST

This unit is capable of detecting the atmospheric pressure changes. Based on collected weather

data, it forecasts the weather for the next 12 to 24 hours.

When the

display

shows...

Forecast

is... Sunny Partly

Cloudy

Heavy

Rainy

Heavy

Snowy

Cloudy Rainy Snowy

NOTE: The weather forecast accuracy is approximately 70%.

The main unit display shows forecasted (predicted) not current conditions. The

SUNNY icon indicates clear weather, even when displayed during the night-time.

PRESSURE OPERATION

The pressure window displays: current barometric pressure, sea level pressure, and weather

forecast. The information contains a number of historical statistics: pressure/ temperature/

humidity history bar-chart for the past 24 hours

Pressure can be measured in inHg, hPa/mBar or mmHg, and altitude is determined in either

meters or feet.

IMPORTANT: There are three viewing options available: barometric pressure SEA LEVEL

or and LOCAL ALTITUDE. Local pressure is a measured value (can’t be adjusted) while Sea

Level Altitude & are variables that you can enter. It is advisable to select and program only

one of the variables and to allow the unit to calculate the third value.

The unit is designed to measure pressure changes at your , when speciﬁc location LOCAL

barometric pressure is selected. Information for programming your unit, with either Altitude

or values, may be obtained from GPS readings, online from the Internet, etc.Sea Level

SEA LEVEL barometric pressure provides you with information about pressure changes at

lower elevations in your surrounding area SEA LEVEL. The pressure value can be set to

match your local metro area weather information. (Sources – local TV or radio station, etc.)

SETTING INITIAL PRESSURE PARAMETERS

IMPORTANT: Allow the unit to set without touching ANY buttons for about 6-8 minutes

during the main unit initial set up. This will give the unit time to synchronize with remotes,

stabilize pressure readings and settle with default settings.

SELECT PRESSURE UNITS OF MEASURE

Press ( ) or ( ),as needed, until the pressure icon , to the left of UP ▲DOWN ▼“PRESSURE”

the barometric pressure value, begins to flash.

• Press button, to toggle through selections until MODE “SEA LEVEL” “LOCAL” or

barometric pressure is displayed.

• Press and hold button to enter the pressure unit selection mode. Press the ( ) or MEM UP ▲

( ) button to select the preferred units of measure for pressure: inHG (English), DOWN ▼

hPa/mBar (scientific) or mmHg (metric)

• Press button to confirm your selection. Then press to move to the MEM MODE ALTITUDE

unit selection mode. Press the ( ) or ( ) button to select pressure unit as UP ▲DOWN ▼

FEET METER or .

• Press button to confirm and hold to move to the MEM MODE ALTITUDE value selection

mode.

• Press UP DOWN( ) or ▲ ( ) to select or adjust the altitude value to your location. (Press ▼

and hold either button for accelerated digit advance)

• Press to confirm the programming selection.MODE

(NOTE: The unit will automatically exit programming mode if it does not detect a button

press after 2 minutes.)

VIEWING PRESSURE AND ALTITUDE INFORMATION

To view pressure or altitude information, press button. The display will alternate MODE

between the sea level pressure, local pressure and local altitude screens.

PROGRAMMING SEA LEVEL PRESSURE (not required if you did altitude)

• Press and hold , until the barometric pressure digits are flashing.MODE

• Enter the desired sea level pressure value by pressing UP ( ) or ( ) buttons. (Press ▲DOWN ▼

and hold either button for accelerated digit advance.)

• Press MODE, to confirm sea level value selection.

CHANGING PRESSURE AND ALTITUDE UNITS

• Press MODE “LOCAL” as needed, until pressure is displayed.

• Press and hold MEM/ HISTORY, until the pressure unit is flashing.

• Change local or sea level pressure units by pressing the UP ( ) or ( ) buttons to ▲DOWN ▼

select the pressure units. Choose from: inHg, hPa/mBar or mmHg.

• Press MEM button to confirm your selection.

• Press MODE button until the local altitude value will be displayed

• Press and hold MEM button until the altitude unit is flashing.

• Select the ALTITUDE DOWN unit:, meters or feet, by pressing UP ( ) or ▲ ( ) buttons.▼

• Press MEM button to confirm your selection.

VIEWING SEA LEVEL PRESSURE HISTORY

• In pressure mode, press button entering the sea level pressure display.MEM

• When the SEA LEVEL is displayed, press MEM button repeatedly viewing the sea

level pressure history for the past 24 hours in 1 hour intervals.

• If no buttons are pressed for 5 seconds, the unit will automatically return to the default

Pressure and Weather Forecast Mode.

VIEWING PRESSURE, TEMPERATURE AND HUMIDITY CHARTS

The bar chart in Pressure Window can be configured to display a historical data for the sea

level pressure and temperature or humidity for channel 1.

After selecting the Pressure Window, press and hold button to toggle the bar chart ALARM

between the sea level pressure with a word displayed at the right bottom corner “PRESSURE”

of the chart, temperature with a thermometer icon and and a humidity with icon “CH1” “RH”

and . “CH1”

MOON PHASE ICONS

New

Moon

Waning

Crescent

First

Quarter

Waxing

Gibbous

Full

Moon

Waning

Gibbous

Last

Quarter

Waning

Crescent

TEMPERATURE/ HUMIDITY WINDOW

The main unit supports up to 3 remote sensors, corresponding to a separate channel of the

temperature and relative humidity display. The temperature can be displayed in Celsius (ºC) or

Fahrenheit (ºF).

The main unit carries the temperature and humidity sensor and uses this data to calculate an

indoors comfort level - Wet, Comfort or Dry.

A temperature alert function is available for all channels. It can be programmed to sound if the

channel temperature exceeds or falls below the pre-set upper and lower limits.

REMOTE SENSORS STATUS

The wave icon above the current channel icon shows the connection status of the corresponding

remote sensor:

Icon Status

Searching for the signals from the remote sensor

Corresponding remote sensor signal received

successfully

No signals received for over 1 hour

SEARCH FOR REMOTE SENSORS

• The main unit can be manually activated to search for the signals from remote sensors by

pressing and holding ( ) button.DOWN ▼

OPERATION

• To select the indoor/ outdoor temperature and humidity mode, press ( ) or ( ) UP ▲DOWN ▼

until the icon flashing with a beep sound alert.IN

VIEWING REMOTE (CHANNEL) TEMPERATURE AND HUMIDITY

Static Display:

• Press the button to select measurements from different remote sensors, each is CHANNEL

MODE to a unique channel 1, 2 or 3.

Channel Auto-Scan Display:

• To enable an automatic scan of all channels, press and hold , until the icon is CHANNEL

displayed. The measurements from each remote channel will be alternately displayed with a 5

seconds viewing.

NOTE: are more than one the channel auto-scan feature can be active only if there remote

sensors operating and are MODE to different channels.

PROGRAMMING TEMPERATURE IN CELSIUS OR FAHRENHEIT

• Press and hold MODE button for 3 seconds to toggle the temperature unit in Celsius (ºC) or

Fahrenheit (ºF).

SETTING TEMPERATURE ALARM

• Press button selecting the desired alarm, the upper temperature alert with i con (if ALARM

disabled, displays ), or lower temperature alert with icon (if disabled, displays ).OFF OFF

• Press and hold button until the temperature digits flashing.ALARM

• Adjust the temperature digits using the ( ) or ( ). Press and hold either button UP ▲DOWN ▼

for fast digits advance

• Press the to confirm selection and return to the temperature alarm selection screenALARM

ACTIVATING OR DEACTIVATING TEMPERATURE ALARMS

• Once the above alerts are displayed, press the UP DOWN( ) or ▲ ( ) to enable or disable ▼

the corresponding alert.

VIEWING MAX/MIN AND MINIMUM READINNGS

Press the MEM/ HISTORY button recalling:

• Current temperature and humidity

• Minimum temperature and humidity

• Maximum temperature and humidity at the remote location.

RESETTING TEMPERATURE MEMORIES

Press and hold button for 3 seconds to clear all channel memories.MEM

COMFORT LEVEL INDICATION

The main unit is capable of detecting and displaying the current indoor comfort levels of

surrounding environment. The comfort level based on the combination of the current indoor

temperature and humidity readings. The following comfort levels may be displayed:

COMFORT (comfortable); WET (wet) and DRY (dry)

Indicator

displayed

COM

WET

DRY

Temperature

Range

Humidity

Range

Shows current

condition

20°C to 25°C

(68°F to 77°F)

40%RH-

70%RH

Ideal relative humidity

and temperature

-5°C to 50°C

(23°F to122°F)

OVER

70%RH

Contains excess

moisture

-5°C to 50°C

(23°F to122°F)

BELOW

40%RH

Contains inadequate

moisture

CLOCK WINDOW

RADIO CONTROLLED TIME

The radio controlled signal for time (DCF 77) is transmitted from the central atomic clock in

Frankfurt/Main in short intervals. It has a reception range of approx. 1500 km. If the tower icon

is not fully lit, or if the time and date are not set automatically, please consider the following:

• During night-time hours, atmospheric disturbances are typically less severe and radio signal

reception may improve. A single daily reception is sufficient enough to keep the clock

accuracy within 1 second.

• Make sure the unit is positioned at 2 meters distance from any interference source such as a

TV, computer monitor, microwave, etc.

• Within concrete wall rooms such as basements or office buildings, the received signal may

be weakened. Always place the main unit near the window for better reception.

Once the radio controlled time signal is received, the date and time will be set automatically,

and the [ ] icon will appear.

ICON Time Signal Reception Strength

Undefined data(Flashing)

No Reception for the past 24 hours

Weak signal, but can be decoded

Strong signal

MANUAL SETTINGS

To select the time mode, press UP ( ) or DOWN ( ) until the IN icon flashing with a beep ▲ ▼

sound alert.

TIME AND CALENDER

• Press and hold button until the day of week language abbreviation will flashMODE “ENG”

• Press the ( ) or ( ) selecting the day of the week in English, German, French, UP ▲DOWN ▼

Italian, Spanish, Dutch or Swedish.

• After the language of weekday is set, press button to confirm and move to the next MODE

parameter (year)

• Continue setting the year, month, day, time format (12 or 24 hours), local hour and minutes,

using the same technique

• After programming is complete the display will return to the default hour and minutes with

seconds display.

CLOCK ALARMS

There are two time alarms – Weekday alarm ( ) and Single day alarm( ) - and one Ice

Warning Alarm ( ).

• If Weekday ( ) alarm is activated, it will sound at the set time and the alarm icon will

flash Mondays through Fridays

• If ( ) day alarm is activated, it will sound at the set time and the alarm icon will flash Single

only for this specific day and will not activate on subsequent days

• If Ice Warning Alarm ( ) is activated, in will sound at the set time and alarm icon

will flash once the remote temperature for Channel One (1) will reach 32°F(0°C) and below

NOTE: Ice Warning Alarm can be set only if one or both - Weekday or Single alarm - are

programmed.

SETTING THE WEEKDAY ( ) AND SINGLE DAY ( ) ALARMS

• Press ALARM button once to enter into the alarms setting mode. The default alarm is a

Weekday alarm ( ). The abbreviation “ ” with a letter “ ” next to it will be OFF

displayed, if the alarm has not been set previously

• Press and hold button for two seconds. The hour digit will flashALARM

• Adjust the hour using UP DOWN( ) or ▲ ( ) buttons▼

• Press button again. The minute digits will flashALARM

• Adjust the minutes using ( ) or ( ) buttonsUP ▲DOWN ▼

• Press button again to confirm and the weekday alarm time will be setALARM

• Set ( ) day alarm if desired in the same mannerSingle

SETTING THE ICE WARNING ALARM ( )

If Weekday ( ) or Single day ( ) alarm is MODE, the Ice Warning Alarm ( ) can be

programmed.

• Press ALARM button once to enter into the Ice Warning Alarm setting mode. The

abbreviation OFF with a PRE-AL next to it will be displayed.

• Press and hold ALARM button for two seconds. The number 30 will flash, meaning that if

selected, the alarm will sound 30 minutes earlier than the Weekday or Single alarm.

• Select the desired Ice Warning Alarm interval in 15 minutes increments between 15 and 90

minutes, using UP ( ) or DOWN ( )buttons▲ ▼

• Press ALARM button to confirm and exit from the alarm setting mode.

ACTIVATING/ DEACTIVATINSALARMS

• Press button to enter into the desired alarm mode.ALARM

• Press ( ) to activate alarm and the corresponding icons , or UP ▲

will be displayed.

• Press ( ) to deactivate alarm until is displayed.DOWN ▼“OFF”

MAINTANANCE

CHANGING BATTERIES

• If the low battery indicator lights up, replace batteries in the corresponding unit.

• Do not mix old and batteries.

CLEANING

The main unit and remote sensors housings can be cleaned with a damp cloth. Small parts can

be cleaned with a cotton tip or pipe-cleaner. Never use abrasive or corrosive cleaning agents or

solvents. Do not immerse electronic components in water.

TROUBLESHOOTING

Check here before contacting customer service.

Issue

Main unit Radio Controlled

Time signal is not

received

Cannot locate

remote sensor

Data does not

match data on the

main unit

Place unit by the window and keep it there

overnight

Check batteries

Check location

Press and hold ( ) button on the DOWN ▼

main unit to search for the signal form the

remote sensor

Initiate manual sensor search (Press and hold

DOWN ( ) button on the main unit)▼

Remote sensor

Symptom Solution

PRECAUTIONS

This product is engineered to give you years of satisfactory service if handled carefully. Here

are a few precautions:

• Do not immerse the units in water.

• Do not clean the units with abrasive or corrosive materials. They may scratch the plastic parts

and corrode the electronic circuits.

• Do not subject the product to excessive force, shock, dust, temperature, or humidity, which

may result in malfunctions, shorter lifespan, damaged batteries, and damaged parts.

• Do not tamper with the units internal components. Doing so will invalidate the warranty and

may cause damage. These units contain no user-serviceable parts.

• Use only fresh batteries. Do not mix new and old batteries.

• Read the user's manual thoroughly before operating the units.

CAUTION

- The content of this manual is subject to change without further notice.

- Due to printing limitation, the displays shown in this manual may differ from the actual

display.

- The contents of this manual may not be reproduced without the permission of the

manufacturer. SPECIFICATIONS

Main Unit

Indoor Temperature

Proposed operating range: 0°C to +50°C

Temperature resolution: 0.1°C (0.2°F)

User-selectable (°C or °F) temperature display

Humidity (Indoor)

Operating Range: 30% to 80%

Resolution: 1%

Accuracy: 7%

Sampling Interval: 10 seconds

Weather Forecast: in seven large icons: sunny, slightly cloudy, cloudy, rainy, heavy rainy,

snowy and heavy snowy.

Maximum number of remote sensors: 3 (one included)

Readings update interval: every 45 seconds

Low battery indicator

Clock

Radio Controlled time (DCF77)

12/24 hour time format

Crescendo 2 minutes alarm with 8 minutes snooze

Barometric Pressure

Measuring Range: 14.75 inHg to 32.44 inHg (500 Hpa to 1100Hpa); (374.5 mmHg to

823.8 mmHg)

Resolution: 0.003 inHg (0.1 Hpa, 0.08 mmHg)

Accuracy: 0.015 inHg (5 Hpa; 0.38 mmHg)

Sampling interval: 20 minutes

Altitude Compensation Range: -200m to +5000 m

Remote Sensor

Remote Temperature

Proposed operating range with alkaline batteries:

-20°C to + 60°C

Temperature resolution: 0.1°C/ 0.2°F

Humidity (Outdoor)

Operating Range: 30% to 80%

Resolution: 1%

Accuracy: 7%

Sampling Interval: 10 seconds

Transmitting Interval: around 47 seconds

RF Transmission Frequency: 433 MHz

RF range: Maximum 30 meters

Temperature transmission cycle: approximately 45 seconds

Wall-mount of Table stand

Power

Main unit: 2 CR2032 size 3V batteries (not included)

Remote Sensor: 2 AAA size 1.5V batteries (not included)

Dimensions

Main unit: 178(L) x 120(H) x 9.5(W) mm

Remote sensor: 37.5(L) x 110(H) x 23(W) mm

EC-DECLARATION OF CONFORMITY

Product: TE636NL

This product contains the approved transmitter and complies with the essential requirements of

Article 3 of the R&TTE 1999/5/EC Directives, if used for its intended use and that the

following standard(s) has/have been applied:

Eﬀicient use of radio frequency spectrum (Article 3.2 of the R&TTE Directive)

EN 300 220-2,V2.1.2:2007-06

EN 300 330-2,V1.3.1:2006-04

Electromagnetic compatibility (Article 3.1.b of the R&TTE Directive)

EN 301 489-3,V1.4.1:2002-08

Low voltage directive applied standard(s)

EN 60950-1:2006+A11:2009

Electromagnetic compatibility (Article3.1.b of the R&TTE Directive)

EN 50371:2002

Additional information:

The product is therefore conform with the Low Voltage Directive 73/23/EC, the EMC Directive

89/336/EC and R&TTE Directive 1999/5/EC (appendix II) and carries the respective CE

marking.

• The radio controlled clock receiver is programmed that it will search for the time signal daily

for 0:00, 3:00, 6:00, and 12:00 am.

• To enable or disable the radio controlled time receiver, press and hold UP ( ) button for 3 ▲

seconds. If atomic time reception is activated, a tower icon will start flashing. If reception is

disabled, the tower icon will disappear.

• If the time signal has not been received in 8 minutes, you may set the time manually.

23 24

25 26

27 28

29 30

Specyfikacje produktu

Marka:	Ventus
Kategoria:	Stacja pogodowa
Model:	W636

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Ventus W636, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą

Twoje imię*

Twój email*

Napisz tutaj swoje pytanie

Instrukcje Stacja pogodowa Ventus

Ventus W210 Instrukcja

3 Października 2024

Ventus W640 Instrukcja

3 Października 2024

Ventus W154 Instrukcja

3 Października 2024

Ventus W225 Instrukcja

3 Października 2024

Ventus W232 Instrukcja

20 Września 2024

Ventus W160 Instrukcja

18 Września 2024

Ventus W233 Instrukcja

15 Września 2024

Ventus V193-R Instrukcja

14 Września 2024

Ventus W831 Instrukcja

11 Września 2024

Ventus W224-7 Instrukcja

11 Września 2024

Instrukcje Stacja pogodowa

Najnowsze instrukcje dla Stacja pogodowa

Hyundai WSP 3080 Instrukcja

15 Października 2024

Livoo SL262 Instrukcja

9 Października 2024

Muse M-085 WS Instrukcja

8 Października 2024

La Crosse Technology S77925v3 Instrukcja

8 Października 2024

TFA 30.5045.54 Instrukcja

8 Października 2024

La Crosse Technology V61 Instrukcja

8 Października 2024

Davis DAV-6520 Instrukcja

7 Października 2024

Brandson 304633 Instrukcja

7 Października 2024

Brandson 305385 Instrukcja

7 Października 2024

GlobalTronics WT-440 Instrukcja

6 Października 2024