Instrukcja obsługi Ventus W155

Ventus Stacja pogodowa W155

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Ventus W155 (100 stron) w kategorii Stacja pogodowa. Ta instrukcja była pomocna dla 16 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/100

VENTUS W155

ENGLISH……………………………………………………………………………..PAGE 01

GERMAN……………………………………………………………………………..PAGE 17

DANISH………………………………………………………………………………PAGE 35

NORWEGIAN………………………………………………………………………..PAGE 55

SWEDISH…………………………………………………………………………….PAGE 70

FINNISH………………………………………………………………………………PAGE 85

W155. Ventus Wireless Weather station

Owner’s Manual

Thank you for purchasing the new generation of professional weather station. Designed and engineered

with the state-of-art technology and components, this instrument will provide accurate and reliable

measurement of wind speed & direction, wind chill, daily/weekly/monthly/accumulated rainfall,

barometric pressure, weather forecast, indoor/outdoor humidity, temperature, heat index & dew point as

well as radio-controlled alarm clock. Read this manual carefully to fully explore the features and

functions of the new product.

In this package you will nd:

One monitor (Receiver)

One anemometer (Transmitter – transmit wind & outdoor Channel-1 temperature/humidity data)

One rain gauge (Transmitter – transmit rainfall data)

Mounting hardware for rain gauge (2 sets of screws & plastic screw plugs)

Mounting hardware for anemometer (2 pieces of U-shape metal plate, 4 sets of Hex screws & nuts)

One owner’s’ manual

Additional tools needed for installation

- Small Phillips screwdriver

- Hexagonal Key

- Electric drill

- Pencil

- Level

- Mast, 1 – 1.25 inch (2.54 – 3.18 cm) in diameter (to mount the anemometer)

Installation

The weather station operates at 433MHz and does not require wire installation among the component

parts. To ensure successful installation and the best performance, we recommend you follow the

installation instructions in the order they appear in this manual.

1. Battery & adapter installation for the monitor (receiver)

Main Power source: Plug in the adapter jack into the side of the unit for basic operation and continuous

backlight.

Backup Power: Open the battery door and insert 6 pieces of AA batteries according to the polarity

indicated, close the battery cover.

Sea level pressure setting

After battery/adapter installation, the monitor will enter sea level pressure setting mode directly and the

pressure reading will ash. Press “ ” or “ ” to set the sea level pressure value. Press “PRESSURE” to ▲ ▼

conrm the setting and exit. This allows the unit to provide a more accurate weather forecast &

pressure reading.

You can also set the sea level pressure any time after the installation is completed. For more

information, see “WEATHER FORECAST & BAROMETRIC PRESSURE” section.

Note: you may obtain the current sea level pressure from the weather web site for your locate area.

2. Selecting a location for the anemometer

Select a mounting location for the anemometer that is:

- Outdoors, not blocked on top or sides, so wind can freely reach the anemometer

- Within 30 meter open area from the monitor. Reduce distance if obstacles is between the

anemometer & the monitor

The best location for the anemometer is usually mounted on a mast in an open area where wind is not

blocked on top or sides, or above roof level on the building where the monitor is located.

Testing the eective transmission range

Before mounting the anemometer, measure the distance between the monitor & anemometer and be

sure it is within the eective transmission range. It is recommended to perform a simple RF

transmission test before mounting.

1) Place the monitor in your selected indoor location and install adapter & batteries (see “Battery &

adapter installation for the monitor” section above)

2) Place the anemometer horizontally in your selected outdoor location. Loosen the screws on the

battery door with a small Phillips screwdriver and open the battery door. Insert 2 pieces of AA

batteries according to the polarity indicated. Close the battery door and tighten the screws.

3) Hold “CHANNEL/SEARCH” button on the monitor for 3 seconds and the wind direction,

temperature & humidity icons will ash on the display. The monitor is now searching for all remote

sensors for 2 minutes.

4) If valid wind direction, wind speed and channel-1 temperature/humidity readings are shown on the

monitor within 2 minutes, the RF transmission is successful and the anemometer & monitor are

within the eective transmission.

If above readings are not shown after 2 minutes of searching, the transmission is failed.

Shorten the distance between the anemometer & monitor. Reset the anemometer by removing all

batteries from the anemometer & wait for 10 seconds before re-installing the batteries again.

Repeat step 3 & 4 until the transmission is successful.

5) Remove all batteries from the anemometer before mounting and calibration.

Specyfikacje produktu

Marka:	Ventus
Kategoria:	Stacja pogodowa
Model:	W155

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Ventus W155, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą

Twoje imię*

Twój email*

Napisz tutaj swoje pytanie

Instrukcje Stacja pogodowa Ventus

Ventus W210 Instrukcja

3 Października 2024

Ventus W640 Instrukcja

3 Października 2024

Ventus W154 Instrukcja

3 Października 2024

Ventus W225 Instrukcja

3 Października 2024

Ventus W232 Instrukcja

20 Września 2024

Ventus W160 Instrukcja

18 Września 2024

Ventus W233 Instrukcja

15 Września 2024

Ventus V193-R Instrukcja

14 Września 2024

Ventus W831 Instrukcja

11 Września 2024

Ventus W224-7 Instrukcja

11 Września 2024

Instrukcje Stacja pogodowa

Najnowsze instrukcje dla Stacja pogodowa

Hyundai WSP 3080 Instrukcja

15 Października 2024

Livoo SL262 Instrukcja

9 Października 2024

Muse M-085 WS Instrukcja

8 Października 2024

La Crosse Technology S77925v3 Instrukcja

8 Października 2024

TFA 30.5045.54 Instrukcja

8 Października 2024

La Crosse Technology V61 Instrukcja

8 Października 2024

Davis DAV-6520 Instrukcja

7 Października 2024

Brandson 304633 Instrukcja

7 Października 2024

Brandson 305385 Instrukcja

7 Października 2024

GlobalTronics WT-440 Instrukcja

6 Października 2024