Instrukcja obsługi Velleman KNS4
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Velleman KNS4 (7 stron) w kategorii Speelgoed. Ta instrukcja była pomocna dla 3 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek
Strona 1/7
KNS4 VELLEMAN 1
KNS4 – COPTERMECH
1. Introduction & Characteristics
Thank you for buying the KNS4 ! Read this manual carefully before bringing the device into use.
• Familiarise yourself with the operation of transmissions steered through gears or pulleys.
• Easy to build, no glue or soldering required.
• Dislodge the pre-cut pieces when you need them and not before. Sand the jagged edges before use (sandpaper
included)
• The kit is powered by 2 AA-batteries (not included).
The kits of the KNS-series are supplied with prepunched boards, a gearbox, gears, shafts, a switch, a motor, a
battery holder and all necessary parts.
Note that the figures with the assembly instructions can be found in the second folder “KNS4 – Figures”!!!
2. Parts List
Part n° Quant. Description Part n° Quant. Description
1 1 motor holder
12 2 fixing plate
2 1 battery holder 13 3 PVC tube (1.5 x 15mm)
3 1 motor with wire 14 3 metal shaft (2 x 90mm)
4 15
1 slide switch with wire 3 metal shaft (2 x 70mm)
5 1 plastic tube (L : 15cm) 16 1 belt (black) (126 x 1mm)
6 17 1 metal shaft (2 x 40mm) 1 rubber band (35mm, red)
7 1 pinion gear 18 4 rubber band (40mm red)
8 19 1 face gear 36T/14T (white) 7 fixing plate (L-shaped)
9 20 2 pulley 19.5 x 2mm (blue) 15 nylon pad
10 8 pulley 15 x 2mm (yellow) 21
11 nylon pad
11 22 2 pulley 24 x 2mm (white) 26 self-tapping screw
3. Prepunched Boards (see “KNS4 – Figures
”
)
4. Assembly (see also “KNS4 – Figures
”
)
Fig. 4 : Insert part n°20 in the hole on board n°2 and mount the motor holder according to fig. 4.
Fig. 5 : Insert part n°20 (x 8) in boards n°1 & 4. Insert part n°7 between boards 1 & 4. Insert 2 x part n°15 in board
n°4 and through the pulley (part n°10). The metal shafts come out the other side of board n°1. Remember
to put the rubber bands (parts n°18 & 16) on the pulley before inserting the metal shaft. Another part n°15
goes through boards n°1 & 4.
Fig. 6 : Cut part n°5 to precisely 32mm. Insert part n°20 in board n°5 first, then put metal shaft n°14 through board
n°5. Mount part n°5 & 8 according to figure 6. Attach board n°5 to boards n°1 & 4 with part n°19.
KNS4 VELLEMAN 2
Fig. 9 : Observe a distance of 10mm between board n°20 and the pulley (part n°10).
Fig. 10 : Fix board n°10 to board n°3 with part n°19.
Fig. 12 : Screw the battery holder (n°2) to the underside of board n°2. The wires pass through board n°2 to make
the connection with the motor and the switch (see fig. 16).
Fig. 13 : Gives a state of affairs.
Fig. 14 : Use one part n°12 to fix boards n°11 & 17 and use a second one to fix boards n°11 & 16.
4. Troubleshooting
• Make sure the wiring is correct
• Note that all shafts (n°6, 14 & 15) in nylon pads (n°20 & 21) should be able to move. This will allow the pulleys &
wheels to run smoothly.
Note : The specifications and contents of this manual can be subject to change without prior notice.
KNS4 – COPTERMECH
1. Inleiding en Kenmerken
Dank u voor uw aankoop ! Lees deze handleiding aandachtig voor u het toestel in gebruik neemt.
• Leer hoe een tandwielaandrijving of een pulley met riemaandrijving werkt.
• Makkelijk te bouwen, zonder lijm of solderen.
• Maak de voorgesneden vormen pas los wanneer u ze nodig hebt. Schuur de scherpe randjes af voor gebruik
(schuurpapier meegeleverd)
• De kit wordt aangedreven door 2 AA-batterijen (niet inbegrepen).
De kits van de KNS-reeks worden geleverd met voorgesneden vormen, tandwielkast, koppeling, stangen,
schakelaar, motor, batterijhouder en alle vereiste onderdelen.
U vindt de figuren met de montagetips in de tweede folder : “KNS4 – Figuren”!!!
2. Lijst van onderdelen
Nr. Hoev. Beschrijving Nr. Hoev. Beschrijving
1 1 motorhouder 12 2 bevestigingsplaat
2 1 batterijhouder 13 3 PVC buis (1.5 x 15mm)
3 1 motor met draad 14 3 metalen as (2 x 90mm)
4 1 glijschakelaar met draad 15 3 metalen as (2 x 70mm)
5 1 plastic buis (L : 15cm) 16 1 riem (zwart) (126 x 1mm)
6 1 metalen as (2 x 40mm) 17 1 aandrijfriem (35mm, rood)
7 1 rondsel
18 4 aandrijfriem (40mm rood)
8 19 1 tandwiel 36T/14T (wit) 7 bevestigingsplaat (L-vormig)
KNS4 VELLEMAN 3
9 20 2 katrol 19.5 x 2mm (blauw) 15 nylon kraagring
10 21 8 katrol 15 x 2mm (geel) 11 nylon kraagring
11 2 katrol 24 x 2mm (wit) 22
26 zelftappende schroef
3. Voorgesneden vormen (zie “KNS4– Figuren”)
4. Montage (zie ook “KNS4– Figuren
”
)
Fig. 4 : Stop n°20 in de opening van plaat n°2. Neem de motorhouder vast zoals aangegeven op fig. 4.
Fig. 5 : Stop onderdeel n°20 (x 8) in platen n°1 & 4. Verbind platen 1 & 4 d.m.v. onderdeel n°7. Stop 2 metalen
assen (n°15) in plaat n°4 en door katrol n°10. De assen gaan via de wand van plaat n°1 terug naar buiten.
Denk eraan om de rubberen riemen (onderdelen n°18 & 16) op de katrollen te bevestigen voor u de
metalen as aanbrengt. Het laatste exemplaar van onderdeel n°15 gaat door platen n°1 & 4.
Fig. 6 : Snijd onderdeel n°5 op precies 32mm. Stop eerst onderdeel n°20 in plaat n°5. en metalen as n°14 door
plaat n°5. Breng onderdelen n°5 & 8 aan volgens figuur 6. Bevestig plaat n°5 aan platen n°1 & 4 met
onderdeel n°19.
Fig. 9 : Tussen plaat n°20 en de katrol (n°10) moet er een afstand zijn van min. 10mm.
Fig. 10 : Maak plaat n°10 vast aan plaat n°3 met onderdeel n°19.
Fig. 12 : Schroef de batterijhouder (n°2) vast aan de onderkant van plaat n°2. Stop de draden door plaat n°2 en
sluit ze aan op de motor en de schakelaar (zie fig. 16).
Fig. 13 : Geeft aan hoe ver we momenteel staan.
Fig. 14 : Gebruik onderdeel n°12 om platen n°11 & 17 vast te maken en doe hetzelfde met platen n°11 & 16.
5 Problemen en oplossingen
• Zorg ervoor dat de bedrading correct is
• De assen (n°6, 14 & 15) in de nylon kraagringen (n°20 & 21) moeten kunnen bewegen zodat de katrollen en de
wielen ongehinderd kunnen draaien.
KNS4 – COPTERMECH
1. Introduction et Caractéristiques
Nous vous remercions de votre achat ! Lisez la notice présente attentivement avant la mise en service du KNS4.
• Familiarisez-vous avec le fonctionnement d'une transmission pilotée par pignons ou par poulies et élastiques.
• Facile à assembler, sans colle ou soudage.
Specyfikacje produktu
Marka: | Velleman |
Kategoria: | Speelgoed |
Model: | KNS4 |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z Velleman KNS4, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje Speelgoed Velleman
6 Października 2024
Instrukcje Speelgoed
- Speelgoed Ikea
- Speelgoed Kindercraft
- Speelgoed Joy-It
- Speelgoed Lego
- Speelgoed Berg
- Speelgoed Hasbro
- Speelgoed DJI
- Speelgoed Chicco
- Speelgoed Spin Master
- Speelgoed Biltema
- Speelgoed Playmobil
- Speelgoed Crivit
- Speelgoed Salta
- Speelgoed Little Tikes
- Speelgoed Chipolino
- Speelgoed Vtech
- Speelgoed Lenoxx
- Speelgoed Peg Perego
- Speelgoed Parrot
- Speelgoed Makeblock
- Speelgoed Carrera
- Speelgoed Kinderkraft
- Speelgoed Smoby
- Speelgoed Mattel
- Speelgoed Jumbo
- Speelgoed Playtive
- Speelgoed Ravensburger
- Speelgoed SereneLife
- Speelgoed BABY Born
- Speelgoed Lorelli
- Speelgoed Arctic
- Speelgoed MJX
- Speelgoed Huffy
- Speelgoed Sunny
- Speelgoed Steren
- Speelgoed King
- Speelgoed Fisher Price
- Speelgoed Tamiya
- Speelgoed X4-Tech
- Speelgoed Ingo
- Speelgoed Feber
- Speelgoed Syma
- Speelgoed Marklin
- Speelgoed Mega Bloks
- Speelgoed WowWee
- Speelgoed Nerf
- Speelgoed KidKraft
- Speelgoed Geomag
- Speelgoed Yuneec
- Speelgoed AXI
- Speelgoed Thames & Kosmos
- Speelgoed Knex
- Speelgoed Laptronics
- Speelgoed Silvergear
- Speelgoed Kids Knex
- Speelgoed Rayline
- Speelgoed Quadro
- Speelgoed Tiamo
- Speelgoed Svexia
- Speelgoed Skippy Buddy
- Speelgoed Fast Rider
- Speelgoed Plusbricks
- Speelgoed Snap Circuits
- Speelgoed Gagato
- Speelgoed BIG
- Speelgoed Dynacraft
- Speelgoed Cosco
- Speelgoed Step2
- Speelgoed Jamara
- Speelgoed Pure Fun
- Speelgoed Dickie
- Speelgoed Hurtle
- Speelgoed Style Me Up
- Speelgoed Bruder
- Speelgoed Rolly Toys
- Speelgoed SpinMaster
- Speelgoed Invento
- Speelgoed Bullet
Najnowsze instrukcje dla Speelgoed
7 Października 2024
7 Października 2024
6 Października 2024
6 Października 2024
6 Października 2024
6 Października 2024
6 Października 2024
6 Października 2024
5 Października 2024
5 Października 2024