Instrukcja obsługi Valcom VIP-801

Valcom Niesklasyfikowane VIP-801

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Valcom VIP-801 (2 stron) w kategorii Niesklasyfikowane. Ta instrukcja była pomocna dla 6 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/2

1 947791

K1 K2 INPUTS

AUDIOAUX

OUTIN AUDIO CC

+24V DC

N.C.

N.O.

N.C.

N.O.

COM

Issue 1

VIP-801-IC

InformaCast® Compliant

Network Audio Port

INSTALLATION

Mounting

The VIP-801-IC is designed for wall or table

mounting.

Table: Provided with the VIP-801-IC are four rubber

pads. Peel the pads from their carrier backing and

place at the four corners of the bottom of the unit.

Wall: Using the brackets and screws provided,

secure the VIP-801-IC to the wall.

Power Connections

The preferred method of powering a VIP-801-IC is

via a power over Ethernet switch meeting the

802.3af specification. If the rear panel barrel

connector is used for power, the preferred power

supply is a Valcom VIP-324.

Make all required signal connections before

applying power to the unit. If powering via 802.3af

Power over Ethernet, make sure all signal

connections via the back panel are made then

connect the VIP-801-IC to the Ethernet switch.

If power is supplied via the barrel connector, make

sure all signal connections are secure. Attach the

unit to the network via the front panel RJ-45

Ethernet connector. Apply power by plugging the

power supply into the VIP-801-IC via the barrel

connector on the rear of the VIP-801-IC.

Network Connection

The VIP-801-IC has one CAT-5 RJ-45 network

connector on the front panel.

Use the supplied CAT-5 patch cable to connect the

VIP-801-IC to an Ethernet switch.

Signal Connections

The VIP-801-IC has 2 active signal connectors on

the rear panel:

 2 Pin screw terminal for audio output

 6 Pin screw terminal for relay connections

(Connectors AUX, K2, INPUTS are not used)

Audio Out: Typically connects to Self Amplified

Speakers or into an amplifier. AUX Input audio

mutes when Audio Out is receiving page audio.

Relay Channels: Access to the form C relay is

provided via three screw terminals (on a six pin

screw terminal block) labeled K1. The common

contact is the middle terminal with the normally

closed (N.C) contact on the left and the normally

open (N.O.) contact on the right. Relay contacts

are rated for 1A @ 24VDC.

Rear View

Status Indicator Lights

The VIP-801-IC has 3 status indication lights on the

front panel:

STATUS: Flashes during normal operation and

solid during system startup.

LINK: Indicates a 100 Mbit Ethernet connection

when illuminated. A non-illuminated LINK LED

indicates a 10 Mbit connection or no network

connection.

ACT: Indicator flashes to indicate network activity.

Setup

The VIP-801-IC will automatically acquire an IP

address (using DHCP) and connect to the

InformaCast server when connected to the network

and powered up. Information specific to your

application will need to be programmed into the

InformaCast server. Refer to the InformaCast

documentation for further information.

TECHNICAL ASSISTANCE

Assistance in troubleshooting is available from

the factory. Call (540) 563-2000 and press 1 for

Technical Support or via email at

support@valcom.com.

When requesting assistance, you should include

all available information. It is strongly suggested

that you go to the web site and follow the trouble

resolution procedure at http://www.valcom.com.

Valcom equipment is not field repairable.

Valcom, Inc. maintains service facilities in

Roanoke, VA. Should repairs be necessary,

attach a tag to the unit clearly stating your

company name, address, phone number,

contact person and the nature of the problem.

Send the unit to:

Valcom, Inc.

Repair & Return Dept.

5614 Hollins Road

Roanoke, Va. 24019-5056

VALCOM LIMITED WARRANTY

Valcom, Inc. warrants its products only to the original purchaser, for its own use, to be free from defects in materials and workmanship under conditions of

normal use and service for a period of one year from the date of shipment. This Limited Warranty obligation shall be limited to the replacement, repair or

refund of any such defective device within the warranty period, provided that:

1. inspection by Valcom, Inc. indicates the validity of the claim;

2. the defect is not the result of damage, misuse or negligence after the original shipment;

3. the product has not been altered in any way or repaired by others and that factory sealed units are unopened (a service charge plus parts

and labor will be applied to units defaced or physically damaged);

4. freight charges for the return of products to Valcom are prepaid;

5. all units 'out of warranty' are subject to a service charge. The service charge will cover minor repairs (major repairs will be subject to

additional charges for parts and labor).

This Limited Warranty is in lieu of and excludes all other warranties, expressed or implied and in no event shall Valcom, Inc. be liable for any

anticipated profits, consequential damages, loss of time or other losses incurred by the buyer in connection with the purchase, operation,

maintenance, installation, removal or use of the product. The maximum liability of Valcom under this warranty is limited to the purchase price of the

specific Product covered by the warranty.

Disclaimer. Except for the Limited Warranty provided herein, the product is provided “as-is” without any warranty of any kind whatsoever including, without

limitation, any WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT.

This warranty specifically excludes damage incurred in shipment. In the event a product is received in damaged condition, the carrier should be notified

immediately. Claims for such damage should be filed with the carrier involved in accordance with the F.O.B. point.

Headquarters:

Valcom, Inc.

5614 Hollins Road Roanoke, VA 24019-5056

Phone: (540) 563-2000 FAX: (540) 362-9800