Instrukcja obsługi US Blaster USB 1392

US Blaster Radia samochodowe USB 1392

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla US Blaster USB 1392 (48 stron) w kategorii Radia samochodowe. Ta instrukcja była pomocna dla 4 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/48
OWNERS MANUAL
CLASS-AB POWER AMPLIFIER
USB 1389 - 1390 - 1391 - 1392
USB 1389 - 1390 - 1391 - 1392
Class-AB Power amplifiers
GENERAL SAFETY INSTRUCTIONS
- Always read the user guide before using the equipment.
- Keep the user guide in a place where everyone can read it.
- Use the equipment indoors and not in humid environments.
- Never remove or insert a plug from or into a wall socket with wet hands.
- If the plug and/or cable and/or cable input of the equipment is damaged it must be repaired by
aprofessional.
- Always take the plug out of the wall socket in the event of a thunderstorm, and also when the
equipment is not being used for a while.
-Never remove the plug from the power socket by pulling on its cable.
- Install the equipment in such a way that sufficient cooling is possible.
- Never use the appliance in the vicinity of heat sources and/or in direct sunlight.
-Make sure that no small objects or liquids can get in to the appliance.
-Only clean the appliance with a slightly moist dust-free cloth. Do not use cleaning products or
solutions!
-The appliance contains no components, other than those mentioned in the user guide that can
be repaired or replaced by the user.
- If the appliance is defective, it must be repaired by a US Blaster qualified repairs company.
- Keep the equipment out of the reach of children.
Keep the packaging safe so that, if the equipment is defective, you can
send it back in its original packaging and so avoid any damage.
©US Blaster Europe BV
Do not carry out any repairs on the equipment yourself; doing so will invalidate the guarantee.
The equipment may also not be modified; doing so will also invalidate the guarantee.
The guarantee is also invalidated if accidents and damage of any form are caused as a result
of improper use and/or not heeding the warnings in general as laid out in this user guide.
US Blaster Europe accepts no responsibility for any personal accidents as a consequence of not
following the safety instructions and warnings. This is also the case for consequential loss in
any form.
USB 1389 - 1390 - 1391 - 1392
Class-AB Power amplifiers
INTRODUCTION
Thank you for purchasing this US BLASTER Class AB full range amplifier for your car audio system.
Now you own an amplifier of uncompromising design and engineering incorporating the latest advan-
ced circuit technology.
You will soon discover the amplifiers’ optimum sound and reliable performance.
US BLASTER amplifiers are adopted by advanced craftsmanship using the highest quality components
and strict quality control system. In order to provide you with long and pleasureable listening, we
recommend that you have your amplifier installed by an authorized US BLASTER dealer. It will ensu-
re installing your product properly and will also increase the warranty to one year. (please see the
warranty section for more details.)
Please read this manual thoroughly to ensure you get the maximum benefit from this amplifier. When
installed properly, this unit will provide you years of trouble-free performance.
DESIGN FEATURES
SMD Hi-Fi audio components.
FR-4 heavy duty double side PCB.
Low ESR high capacitance filter capacitor.
Super noise rejection circuit.
Smart protection system against overload, short circuit, overheat and low voltage.
Gold plated heavyduty connectors.
Intergrated high performance filters.
AMPLIFIER FUNCTIONS
1. Speaker connection
• Never connect the speaker cables with the chassis ground. This could destory your amplifier.
• Check that your speakers are connected correctly which means plus to plus and minus to minus.
We recommend speaker cable from 16 Gauge or up. Other connection ways are shown in the attach-
ment.
2. BATT+
Battery +(plus) terminal. The +(plus) 12 Volt power cable must be connected with a fuse on the bat-
tery +(plus) terminal. We recommenda fuse listed on pre-installation a 12 feet copper cable with 8
Gauge thickness or up.
3. REM
Remote terminal. The remote cable must be connected with the radio remote output
terminal so that the amplifier will switch on and off automatically with the radio. If there are two or
more amplifiers connected to this antenna terminal it might be necessary to add an additional relay.
Please consult your dealer.
4. GND
Chassis ground terminal. The chassis ground cable must be connected very tight on a nearbymassi-
veand electric conductiveplace.
©US Blaster Europe BV

Specyfikacje produktu

Marka: US Blaster
Kategoria: Radia samochodowe
Model: USB 1392

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z US Blaster USB 1392, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje Radia samochodowe US Blaster

US Blaster

US Blaster usb 1389 Instrukcja

25 Września 2024
US Blaster

US Blaster USB 1392 Instrukcja

25 Września 2024

Instrukcje Radia samochodowe

Najnowsze instrukcje dla Radia samochodowe

JVC

JVC KD-R90BT Instrukcja

15 Października 2024
Kenwood

Kenwood KMM-X705 Instrukcja

15 Października 2024
Alpine

Alpine CDM-7870R Instrukcja

14 Października 2024
Hyundai

Hyundai H-CMD2009 Instrukcja

14 Października 2024
Dual

Dual XC4100 Instrukcja

13 Października 2024
Audiovox

Audiovox VXE 3010 Instrukcja

13 Października 2024
MB Quart

MB Quart PAB 5400 Instrukcja

13 Października 2024
Hyundai

Hyundai H-CDM8023 Instrukcja

13 Października 2024
Caliber

Caliber RCD110B Instrukcja

13 Października 2024
JVC

JVC KD-X30 Instrukcja

13 Października 2024