Instrukcja obsługi Tycon Systems RPAL48-180-1000
Tycon Systems
Zonnepaneel
RPAL48-180-1000
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Tycon Systems RPAL48-180-1000 (4 stron) w kategorii Zonnepaneel. Ta instrukcja była pomocna dla 2 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek
Strona 1/4
RPAL48-180- xxxx
200W RemotePro™
▫ Wireless Base Stations
and Client Devices
▫ Surveillance Cameras
▫ Remote Control
▫ Remote Lighting
▫ Off Grid Electronics
Congratulations! on your purchase of the RemotePro 200W ™
Remote Power System. Please take a moment to review this
Qwik Install Guide before use.
Operation Modes: Solar Only operation or Solar with AC/DC
Backup.
Key Features: Industrial Strength, Manageable, 24VDC and
48VDC Output, 7 Gigabit Passive PoE ports, 2.25A Aux Port,
48V 20A MPPT Solar, Automated Alerts, Removable Connec-
tions.
Safety: For your own protection, follow these safety rules.
▫ Perform as many functions as possible on the ground
▫ Do not attempt to install on a rainy, windy or snowy day or if
there is ice or snow accumulation at the install site or if the
site is wet.
▫ Make sure there are no people, pets, etc. below if you are
working on a roof or ladder.
Recommended Tools: Phillips and Small Flat Blade Screwdriv-
ers, 6mm Hex key and 13, 19, 27, 34mm Wrenches
Please help preserve the environment and return
any used batteries to an authorized depot
2
Qwik Install
STEP 1: Select install location where southern sky has no obstructions
that could cause shading on solar panels.
STEP 2: Pour a foundation big enough to hold solar mount anchors
and also provide level support for battery box. See detailed instructions
in solar mount instructions.
STEP 3: Assemble solar array with mount using solar mount instruc-
tions.
STEP 4: Place battery box under solar panels facing towards back of
solar panels. Install 8 batteries in the box in an alternating pattern. Use
rope tied to battery tabs to lower batteries into the box. Connect all 8
batteries in series configuration (Positive to Negative to Positive...)
STEP 5: Install DIN rail to enclosure using the two screws provided.
Install MPPT solar controller to DIN Rail. Remove the Large Green
Connector from the unit.
STEP 6: Find the thermocouple cable that came with the MPPT Solar
Controller and connect the side with the ring lug to one of the batteries
positive or negative terminals, it doesn t matter which one. Connect the ’
battery cable to the Large Green Connector battery inputs and then to
the batteries making sure to observe the proper polarity.
STEP 7: Install the cable glands in the back of the enclosure and route
the long solar panel cables through the cable gland and connect to the
large green connector solar (PV) inputs. A four panel system will use
two of the long cables and a two panel system will use one of the long
cables. You can shorten the cables as necessary for a cleaner install.
You can also lengthen the cables by adding additional lengths of
12AWG cable.
STEP 8: Connect two of the solar panels in series (Positive to Nega-
tive) by plugging the positive from panel 1 to the negative of panel 2
and then connect the long solar cable to the remaining positive and 20’
3
negative connectors from the solar panels. The connectors are keyed
for polarity so they cannot be connected incorrectly. Repeat for a four
panel system.
STEP 9: Once the batteries and solar panels are all connected and
wired to the Large Green Connector, Disconnect PV+ wire and plug the
connector to the MPPT Solar Controller until the connector latches click
into place. The Battery Charging LED should light up for about 60 sec-
onds. Now connect PV+ to the green connector. Battery should Note:
always be connected first and disconnected last from the controller.
STEP 10: Plug the temperature sensor to the Temp Sensor input on
the MPPT Solar Controller. Refer to the TPDIN SC48 20 instruction - -
manual for setup and operation of the MPPT Solar Controller.
STEP 11: Tighten the cable glands on the wires to make weatherproof
connections. Plug unused holes using the supplied hole plugs. If de-
sired, attach the enclosure to the solar mount pole using chain or cable
for security.
STEP 12: You may want to put a fine screen over the vent holes on
either end of the enclosure to keep out insects. Window screen works
well. Be sure to secure the cables so they won t move in the wind. All ’
Specyfikacje produktu
| Marka: | Tycon Systems |
| Kategoria: | Zonnepaneel |
| Model: | RPAL48-180-1000 |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z Tycon Systems RPAL48-180-1000, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje Zonnepaneel Tycon Systems
23 Września 2024
23 Września 2024
Instrukcje Zonnepaneel
- Zonnepaneel LG
- Zonnepaneel Sharp
- Zonnepaneel Enphase
- Zonnepaneel Growatt
- Zonnepaneel BenQ
- Zonnepaneel Vivanco
- Zonnepaneel EasyMaxx
- Zonnepaneel Xtorm
- Zonnepaneel Gre
- Zonnepaneel Arlo
- Zonnepaneel Fantini Cosmi
- Zonnepaneel Projecta
- Zonnepaneel Cedel
- Zonnepaneel Paulmann
- Zonnepaneel SolarEdge
- Zonnepaneel FOX ESS
- Zonnepaneel Goal Zero
Najnowsze instrukcje dla Zonnepaneel
22 Września 2024
22 Września 2024
21 Września 2024
21 Września 2024
21 Września 2024
15 Września 2024
15 Września 2024
15 Września 2024
14 Września 2024
14 Września 2024