Instrukcja obsługi Tru Components TCN4S-24R

Tru Components termostat TCN4S-24R

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Tru Components TCN4S-24R (2 stron) w kategorii termostat. Ta instrukcja była pomocna dla 3 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/2

Read and understand the instruction manual before using the product.

For your safety, read and follow the below safety considerations before using. For your safety,

read and follow the considerations written in the instruction manual.

Keep this instruction manual in a place where you can find easily.

The specifications, dimensions, etc are subject to change without notice for product improvement.

Safety Considerations

• Observe all ‘Safety Considerations’ for safe and proper operation to avoid hazards.

• symbol indicates caution due to special circumstances in which hazards may occur.

Warning Failure to follow instructions may result in serious injury or death

01. Fail-safe device must be installed when using the unit with machinery that may cause

serious injury or substantial economic loss.(e.g. nuclear power control, medical equipment,

ships, vehicles, railways, aircraft, combustion apparatus, safety equipment, crime/disaster

prevention devices, etc.)

Failure to follow this instruction may result in personal injury, economic loss or fire.

02. Do not use the unit in the place where flammable/explosive/corrosive gas, high humidity,

direct sunlight, radiant heat, vibration, impact or salinity may be present.

Failure to follow this instruction may result in explosion or fire.

03. Install on a device panel to use.

Failure to follow this instruction may result in fire or electric shock.

04. Do not connect, repair, or inspect the unit while connected to a power source.

Failure to follow this instruction may result in fire or electric shock.

05. Check ‘Connections’ before wiring.

Failure to follow this instruction may result in fire.

06. Do not disassemble or modify the unit.

Failure to follow this instruction may result in fire or electric shock.

Caution Failure to follow instructions may result in injury or product damage

01. When connecting the power input and relay output, use AWG 20 (0.50 mm 2) cable or over, and

tighten the terminal screw with a tightening torque of 0.74 to 0.90 N m.

When connecting the sensor input and communication cable without dedicated cable, use

AWG 28 to 16 cable and tighten the terminal screw with a tightening torque of 0.74 to 0.90 N

Failure to follow this instruction may result in fire or malfunction due to contact failure.

02. Use the unit within the rated specifications.

Failure to follow this instruction may result in fire or product damage

03. Use a dry cloth to clean the unit, and do not use water or organic solvent.

Failure to follow this instruction may result in fire or electric shock.

04. Keep the product away from metal chip, dust, and wire residue which flow into the unit.

Failure to follow this instruction may result in fire or product damage.

Cautions during Use

• Follow instructions in ‘Cautions during Use’. Otherwise, it may cause unexpected accidents.

• Check the polarity of the terminals before wiring the temperature sensor.

• For RTD temperature sensor, wire it as 3-wire type, using cables in same thickness and length. For

thermocouple (TC) temperature sensor, use the designated compensation wire for extending wire.

• Keep away from high voltage lines or power lines to prevent inductive noise. In case installing power

line and input signal line closely, use line filter or varistor at power line and shielded wire at input

signal line. Do not use near the equipment which generates strong magnetic force or high frequency

noise.

• Install a power switch or circuit breaker in the easily accessible place for supplying or disconnecting

the power.

• Do not use the unit for other purpose (e.g. voltmeter, ammeter), but temperature controller.

• When changing the input sensor, turn off the power first before changing. After changing the input

sensor, modify the value of the corresponding parameter.

• Make a required space around the unit for radiation of heat. For accurate temperature measurement,

warm up the unit over 20 min after turning on the power.

• Make sure that power supply voltage reaches to the rated voltage within 2 sec after supplying power.

• Do not wire to terminals which are not used.

• This unit may be used in the following environments.

- Indoors (in the environment condition rated in ‘Specifications’)

- Altitude Max. 2,000 m

- Pollution degree 2

- Installation category II

Product Components

• Product (+ bracket) • Instruction manual

Specifications

Series TCN4S-24R

Power supply 100 - 240 VAC~ 50/60 Hz

Permissible voltage

range 90 to 110 % of rated voltage

Power consumption ≤ 5 VA

Sampling period 100 ms

Input specification Refer to 'Input Type and Using Range.

Control

output Relay 250 VAC~ 3A, 30 VDC~ 3A, 1a

Alarm output 250 VAC~ 1 A 1a

Display type 7 Segment (red, green), LED type

Control

type

Heating,

Cooling ON/OFF, P, PI, PD, PID Control

Hysteresis 1 to 100 (0.1 to 50.0) °C/°F

Proportional band (P) 0.1 to 999.9 °C/°F

Integral time (I) 0 to 9,999 sec

Derivative time (D) 0 to 9,999 sec

Control cycle (T) 0.5 to 120.0 sec

Manual reset 0.0 to 100.0%

Relay

life

cycle

Mechanical ≥ 5,000,000 operations

Electrical OUT1/2: ≥ 200,000 operations (load resistance: 250 VAC~ 3 A)

AL1/2: ≥ 300,000 operations (load resistance: 250 VAC~ 1 A)

Dielectric strength Between the charging part and the case: 2,000 VAC~ 50/60 Hz for 1 min

Vibration 0.75 mm amplitude at frequency of 5 to 55 Hz in each X, Y, Z direction for 2 hours

Insulation resistance ≥ 100 MΩ (500 VDC megger)

Noise immunity ±2 kV square shaped noise (pulse width: 1 µs) by noise simulator R-phase,

S-phase

Memory retention ≈ 10 years (non-volatile semiconductor memory type)

Ambient temperature -10 to 50 °C, storage: -20 to 60 °C (no freezing or condensation)

Ambient humidity 35 to 85%RH, storage: 35 to 85%RH (no freezing or condensation)

Insulation type Mark: , double or reinforced insulation (dielectric strength between the measuring

input part and the power part: 2 kV)

Certification

Unit weight (packaged) TCN4S: ≈ 100 g (≈ 147 g)

Input Type and Using Range

The setting range of some parameters is limited when using the decimal point display.

Input type Decimal

point Display Using range (°C) Using range (°F)

Thermo

-couple

K (CA) 1 -50 to 1,200 -58 to 2,192

0.1 -50.0 to 999.9 -58.0 to 999.9

J (IC) 1 -30 to 800 -22 to 1,472

0.1 -30.0 to 800.0 -22.0 to 999.9

L (IC) 1 -40 to 800 -40 to 1,472

0.1 -40.0 to 800.0 -40.0 to 999.9

T (CC) 1 -50 to 400 -58 to 752

0.1 -50.0 to 400.0 -58.0 to 752.0

R (PR) 1 0 to 1,700 32 to 3,092

S (PR) 1 0 to 1,700 32 to 3,092

RTD

Cu50 Ω 1 -50 to 200 -58 to 392

0.1 -50.0 to 200.0 -58.0 to 392.0

DPt100 Ω 1 -100 to 400 -148 to 752

0.1 -100.0 to 400.0 -148.0 to 752.0

■Display accuracy

Input type Using

temperature Display accuracy

Thermocouple RTD

At room

temperature

(23°C ±5 °C)

(PV ±0.5% or ±1 °C higher one) ±1-digit

• Thermocouple R, S below 200 °C:

(PV ±0.5% or ±3 °C higher one) ±1-digit

Over 200 °C:

(PV ±0.5% or ±2 °C higher one) ±1digit

• Thermocouple L, RTD Cu50 Ω:

(PV ±0.5% or ±2 °C higher one) ±1-digit

Out of room

temperature

range

(PV ±0.5% or ±2 °C higher one) ±1-digit

• Thermocouple R, S below 200 °C:

(PV ±1.0% or ±6 °C higher one) ±1digit

Over 200 °C:

(PV ±0.5% or ±5 °C higher one) ±1digit

• Thermocouple L, RTD Cu50 Ω:

(PV ±0.5% or ±3 °C higher one) ±1digit

• If the input specification is set to 'decimal point 0.1' display, add ±1 by accuracy standard.°C

Unit Descriptions

1. PV Display part (red)

• RUN mode: Displays PV (Present value)

• Setting mode: Displays parameter name

2. SV Display part (green)

• RUN mode: Displays SV (Setting value)

• Setting mode: Displays parameter setting value

3. Indicator

Display Name Description

AL1/2 Alarm

output Turns ON when the alarm output is ON.

OUT Control

output

Turns ON when control output is ON

• CYCLE/PHASE control of SSR

drive output: Turns ON when MV is

over 3.0% [AC power model]

AT Auto

tuning Flashes during auto tuning every 1 sec

°C, °F Unit Displays selected unit (parameter).

4. Input key

Display Name

[MODE] Mode key

[◄], [▼ ▲], [ ] Setting value

control key

Errors

Display Description Troubleshooting

Flashes when input sensor is disconnected or sensor is

not connected. Check input sensor status.

Flashes when PV is higher than input range.

01) When input is within the rated input

range, this display disappears.

Flashes when PV is lower than input range.

01)

01) Be careful that when / error occurs, the control output may occur by recognizing the maximum or minimum input

depending on the control type.

Dimensions

• Unit: mm

■Panel cut-out

Body Panel cut-out

A B C D E F G H I

TCN4S 48 48 6 64.5 44.8 ≥ 65 ≥ 65 45 +0.6

045 +0.6

■Bracket

TCN4S

Installation Method

■TCN4S

Flathead screwdriver

After mounting the product to panel with bracket, insert the unit into a panel, fasten the bracket by

pushing with a flathead screwdriver.

Dual Display PID Temperature Controllers

TCN4S-24R

Item no.: 3016146

INSTRUCTION MANUAL

TCD210225AB

Connections

■TCN4S

Crimp Terminal Specifications

• Unit: mm, use the crimp terminal of the following shape.

≥3.0

≤5.8

≥3.0

≤5.8

Wire ferrule Fork crimp terminal Round crimp terminal

Terminal

number a b c

1 to 8 6≤ 1.7 ≤ 3.7

9 to 11 6 to 8 ≤ 2.1 ≤ 4.2

12 to 14 6 to 8 ≤ 1.5 ≤ 3.5

Mode Setting

[MODE], [◄], [▲ ▼], [ ]

[MODE] 2 sec

Move digits: [◄]

Change value: [ ], [ ]▲ ▼

Save: [MODE]

[MODE] over 3 sec

Refer to ‘Parameter Reset’

Auto

[MODE] 4 sec

[◄] + [▲ ▼] + [ ] over 5 sec

[ ] + [ ] over 3 sec▲ ▼

SV setting

Parameter 1 group

Parameter 2 group

Parameter reset

Digital input key

RUN RUN

Parameter Reset

01. Press the [ ] + [ ] + [ ] keys for over 5 sec. in run mode, INIT turns ON.◄▲ ▼

02. Change the setting value as YES by pressing the [ ], [ ] keys.▲ ▼

03. Press the [MODE] key to reset all parameter values as default and to return to run mode.

Parameter Setting

• Some parameters are activated/deactivated depending on the model or setting of other parameters.

Refer to the description of each item.

• The setting range in parentheses is for using the decimal point display in the input specification.

• If there is no key input for more than 30 seconds in each parameter, it returns to RUN mode.

• When pressing the [MODE] key within 1 second after returning to the operation mode from the

parameter group, it will enter the parameter group before returning.

• [MODE] key: Saves the current parameter setting value and moves to the next parameter.

[◄] key: Checks the fixed item / Moves the row when changing the set value

[ ], [ ] keys: Selects the parameter / Changes the set value▲ ▼

• Recommended parameter setting sequence: Parameter 2 group → Parameter 1 group → SV setting

mode

Disposal

This symbol must appear on any electrical and electronic equipment placed on the EU

market. This symbol indicates that this device should not be disposed of as unsorted

municipal waste at the end of its service life.

Owners of WEEE (Waste from Electrical and Electronic Equipment) shall dispose of it

separately from unsorted municipal waste. Spent batteries and accumulators, which are not

enclosed by the WEEE, as well as lamps that can be removed from the WEEE in a non-

destructive manner, must be removed by end users from the WEEE in a non-destructive

manner before it is handed over to a collection point.

Distributors of electrical and electronic equipment are legally obliged to provide free take-back of waste.

Conrad provides the following return options free of charge (more details on our website):

• in our Conrad offices

• at the Conrad collection points

• at the collection points of public waste management authorities or the collection points set up by

manufacturers or distributors within the meaning of the ElektroG

End users are responsible for deleting personal data from the WEEE to be disposed of.

It should be noted that different obligations about the return or recycling of WEEE may apply in countries

outside of Germany.

■Parameter 1 group

Parameter Display Default Setting range Condition

1-1 AL1 alarm

temperature Deviation alarm: -F.S. to F.S. °C/°F

Absolute value alarm: Within input range

2-12/14

alarm

operation:

AM1 to AM6

1-2 AL2 alarm

temperature

1-3 Auto tuning OFF: Stop, ON: Execution

2-8 Control

type: PID

1-4 Proportional

band 0.1 to 999.9 °C/°F

1-5 Integral time 0 (OFF) to 9999 sec

1-6 Derivative time 0 (OFF) to 9999 sec

1-7 Manual reset 0.0 to 100.0%

2-8 Control

type: PID &

1-5 Integral

time: 0

1-8 Hysteresis 1 to 100 (0.1 to 50.0) °C/°F 2-8 Control

type: ONOF

■Parameter 2 group

Parameter Display Default Setting range Condition

2-1 Input

specification01) Refer to 'Input Type and Using Range'. -

2-2 Temperature

unit01) °C, °F -

2-3 Input correction -999 to 999 (-199.9 to 999.9) °C/°F -

2-4 Input digital

filter 0.1 to 120.0 sec -

2-5 SV low limit02) Within 2-1 Input specification Input range,

L-SV ≤ H-SV - 1-digit °C/°F

H-SV ≥ L-SV + 1-digit °C/°F

2-6 SV high limit02) -

2-7 Control output

mode03) HEAT: Heating, COOL: Cooling -

2-8 Control type04) PID, ONOF: ON/OFF -

2-9 Control output RLY: relay -

2-11 Control cycle 0.5 to 120.0 sec 2-9 Control

output: RLY

2-12 AL1 alarm

operation

□□□

AM0: Off

AM1: Deviation high limit alarm

AM2: Deviation low limit alarm

AM3: Deviation high, low limit alarm

AM4: Deviation high, low reverse alarm

AM5: Absolute value high limit alarm

AM6: Absolute value low limit alarm

SBA: Sensor break alarm

LBA: Loop break alarm (LBA)

2-13 AL1 alarm

option

■

A: Standard

alarm

C: Standby

sequence 1

E: Standby

sequence 2

B: Alarm latch

D: Alarm latch and

standby sequence 1

F: Alarm latch and

standby sequence 2

• Enter to option setting: Press [◄] key

in 2-12 AL-1 alarm operation.

2-14 AL2 alarm

operation Same as 2-12/13 AL1 alarm operation/

option -

2-15 AL2 alarm

option

2-16 Alarm output

hysteresis 1 to 100 (0.1 to 50.0) °C/°F

2-12/14

AL1/2 alarm

operation: AM1

to 6

2-17 LBA time 0 (OFF) to 9999 sec or auto (auto

tunning)

2-12/14

AL1/2 alarm

operation: LBA

2-18 LBA band 0 (OFF) to 999 (0.0 to 999.9) °C/°F or

auto (auto tunning)

2-12/14

AL1/2 alarm

operation: LBA

& 2-18 LBA

time: > 0

2-19 Digital input

key

STOP: Stop control output, AL.RE: Alarm

reset, AT*: Auto tuning execution, OFF

*2-8 Control

type: PID

2-20 Sensor error

0.0: OFF, 100.0: ON 2-8 Control

type: ONOF

0.0 to 100.0% 2-8 Control

type: PID

2-21 Lock

OFF

LOC1: Parameter 2 group lock

LOC2: Parameter 1/2 group lock

LOC3: Parameter 1/2 group, SV setting

lock

01) Below parameters are initialized when the setting value is changed.

- Parameter 1 group: AL1/2 alarm temperature

- Parameter 2 group: Input correction, SV high/low limit, Alarm output hysteresis, LBA time, LBA band

- SV setting mode: SV

02) If SV is lower than low limit or higher than high limit when the value is changed, SV is changed to the low/high limit value.

If 2-1 Input specification is changed, the value is changed to Min./Max. value of Input specification.

03) When the setting value is changed, setting value of 2-20 Sensor error MV is initialized to 0.0 (OFF).

04) When changing the value from PID to ONOF, each value of following parameter is changed.

2-19 Digital input key: OFF, 2-20 Sensor error MV: 0.0 (when setting value is lower than 100.0)

This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com).

All rights including translation reserved. Reproduction by any method, e.g. photocopy, microlming, or the

capture in electronic data processing systems require the prior written approval by the editor. Reprinting, also

in part, is prohibited. This publication represents the technical status at the time of printing.

*BN3016146 TCN_EN_TCD210225AB_20240417_INST_W

Specyfikacje produktu

Marka:	Tru Components
Kategoria:	termostat
Model:	TCN4S-24R

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Tru Components TCN4S-24R, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą

Twoje imię*

Twój email*

Napisz tutaj swoje pytanie

Instrukcje termostat Tru Components

Tru Components TX4S-14R Instrukcja

18 Grudnia 2024

Tru Components TK4S-14RC Instrukcja

18 Grudnia 2024

Tru Components TCN4S-24R Instrukcja

18 Grudnia 2024

Tru Components TC-7T.81-240NC Instrukcja

29 Września 2024

Tru Components TC-7T.81-230NO Instrukcja

29 Września 2024

Tru Components TC-FKS011NO Instrukcja

29 Września 2024

Tru Components TC-ZR011 Instrukcja

29 Września 2024

Tru Components TC-FKO011NC Instrukcja

29 Września 2024

Instrukcje termostat

Najnowsze instrukcje dla termostat

ATTACK OT80 Instrukcja

17 Grudnia 2024

Warmup +Kit Instrukcja

17 Grudnia 2024

Warmup 5iE Instrukcja

17 Grudnia 2024

EQ-3 CC-RT-O-CnL-W-R5-2 Instrukcja

15 Grudnia 2024

EQ-3 HmIP-WTH-2 Instrukcja

15 Grudnia 2024

EQ-3 HMIP-WTH Instrukcja

15 Grudnia 2024

EQ-3 HMIP-eTRV Instrukcja

15 Grudnia 2024

EQ-3 HM-TC-IT-WM-W-EU Instrukcja

15 Grudnia 2024

EQ-3 HM-CC-RT-DN Instrukcja

15 Grudnia 2024

EQ-3 HMIP-BWTH Instrukcja

15 Grudnia 2024