Instrukcja obsługi Tripp Lite T040-001-DP


Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Tripp Lite T040-001-DP (32 stron) w kategorii Kable do komputerów PC i urządzeń peryferyjnych. Ta instrukcja była pomocna dla 3 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Strona 1/32
Owner’s Manual
DisplayPort/Mini
DisplayPort Cable Tester
Model: T040-001-DP
Espanol 9 • Français 17 • Русский 25
PROTECT YOUR INVESTMENT!
Register your product for quicker service and ultimate peace of mind.
You could also win an ISOBAR6ULTRA surge protector—a $100 value!
www.tripplite.com/warranty
1111 W. 35th Street, Chicago, IL 60609 USA • www.tripplite.com/support
Copyright © 2018 Tripp Lite. All rights reserved.
04-226-933798.indb 1 4/30/2018 3:39:37 PM
2
Package Contents
Product Features
Master Unit
Remote Unit
Carrying Case
Owner’s Manual
All-in-one unit combines a Main Tester with a removable Remote Identifier
Compatible with DisplayPort versions 1.0 through 1.4
Fast and accurate verification of DisplayPort and Mini DisplayPort cables
Displays 19 pin-to-pin wire map and shield connection status to ensure
mapping continuity and proper configuration
Two adjustable test modes available: Continuity and Sweep
04-226-933798.indb 2 4/30/2018 3:39:37 PM
3
Operation
Notes:
Before testing, insert a 9V battery (not included) and ensure the cable being tested
is not yet connected to the tester.
Do not test live cables or any cable connected to an active device. Cables should be
directly connected to the Master Unit, and then to the Remote Unit.
Testing
Simply connect the desired cable to the unit, then switch the Sweep/OFF/
Continuity button to “Continuity” for sync testing, or “Sweep” for step-by-
step testing.
Note: During sync testing, all LEDs illuminate on the wire map at once. During step-by-
step testing, the LEDs will illuminate one at a time.
When testing uninstalled patch cable, you can leave the Main Tester and
Remote Identifier connected.
When testing installed cable, you will need to remove the Remote
Identifier from the Main Tester. Connect one end of the cable to the
appropriate connector on the Main Tester, and the other end of the cable to
the appropriate connector on the Remote Identifier.
Note: Upon switching to the desired testing mode, the LEDs on the Main Tester and
Remote Identifier will illuminate to indicate the results.
If testing DisplayPort-to-DisplayPort cables, use “A pin” side numbers
found on both the Main Tester and Remote Identifier. For DisplayPort-to-Mini
DisplayPort and Mini DisplayPort-to-Mini DisplayPort cables, use “C pin” side
numbers found on both the Main Tester and Remote Identifier.
04-226-933798.indb 3 4/30/2018 3:39:37 PM


Specyfikacje produktu

Marka: Tripp Lite
Kategoria: Kable do komputerów PC i urządzeń peryferyjnych
Model: T040-001-DP

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Tripp Lite T040-001-DP, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą




Instrukcje Kable do komputerów PC i urządzeń peryferyjnych Tripp Lite

Instrukcje Kable do komputerów PC i urządzeń peryferyjnych

Najnowsze instrukcje dla Kable do komputerów PC i urządzeń peryferyjnych