Instrukcja obsługi Tripp Lite SmartRack SRCABLELADDER18

Tripp Lite kabel do komputerów i urządzeń peryferyjnych SmartRack SRCABLELADDER18

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Tripp Lite SmartRack SRCABLELADDER18 (32 stron) w kategorii kabel do komputerów i urządzeń peryferyjnych. Ta instrukcja była pomocna dla 18 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/32

Owner’s Manual

PROTECT YOUR INVESTMENT!

You could also win an ISOBAR6ULTRA surge protector—a $100 value!

www.tripplite.com/warranty

1111 W. 35th Street, Chicago, IL 60609 USA • www.tripplite.com/support

SmartRack® 10 ft. x 18 in.

(3 m x 0.45 m) Cable Ladder

Model: SRCABLELADDER18

1. Introduction 2

1.1 Parts List 2

1.2 Tools Required 2

2. Important Safety Instructions 2

3. Installation 3

3.1 Planning 3

3.2 Ladder Modiﬁcation (Optional) 4

3.3 Ladder Assembly 4

3.4 Installation Across Aisle 5

3.5 Installation Within Row 6

3.6 Ground Connection 7

4. Storage and Service 8

5. Warranty and Product Registration 8

Español 9

Français 17

Русский 25

1. Introduction

2. Important Safety Instructions

SRCABLELADDER18 provides roof-mounted cable routing for Tripp Lite’s SmartRack Enclosures, allowing cable bundles to span aisles and/or

spaces between enclosures in the same row.

Note: Standard installation of SRCABLELADDER18 requires Tripp Lite’s SRCABLETRAY accessory, sold separately.

1.1 Parts List

A Ladder Sections (2)

B Left Assembly Brackets (2)

C Right Assembly Brackets (2)

D Clevis Pins (8)

E Cotter Pins (8)

F Ground Brackets (2)

G M6 Hex-Head Bolts (2)

H 24-inch Ground Cables (3)

I M6 Lock Washers (4)

J M6 Hex Nuts (2)

K Ladder Clamp (4)

L M10x60 mm Carriage Bolts (2)

M M10 Lock Washers (2)

N M10 Hex Nuts (2)

If any parts are missing, visit www.tripplite.com/support.

1.2 Tools Required

• 13 mm Wrench or Crescent Wrench

• Tape Measure

• Hacksaw (optional)

• Drill with 3/8-inch Bit (optional)

SAVE THESE INSTRUCTIONS

This manual contains instructions and warnings that must be followed during the installation and operation of the product

described in this manual. Read all instructions and warnings thoroughly before attempting installation. Failure to comply may

invalidate the warranty and cause property damage and/or personal injury.

• Install in a controlled indoor environment, away from moisture, temperature extremes, ﬂammable liquids and gasses, conductive

contaminants, dust and direct sunlight.

• Provide suitable grounding in accordance with all applicable electrical wiring regulations.

• Do not attempt to climb or walk across any part of the ladder.

• When using tools to cut or drill metal, use eye protection and follow all other safety precautions recommended by the tool manufacturer

and required by applicable safety regulations.

• Use caution and wear safety gloves when handling metal parts that have been cut to length. Sharp edges can cause personal injury and

property damage.

• Use of this equipment in life support applications where failure of this equipment can reasonably be expected to cause the failure of the

life support equipment or to signiﬁcantly affect its safety or effectiveness is not recommended.

L M N

3. Installation

Use a tape measure to determine the distance that SRCABLELADDER18 will bridge. (Preassembling the ladder sections will allow you to

observe their attachment points in place for a more accurate measurement.)

The standard length of SRCABLELADDER18 is 10 feet. If the standard length and the distance between attachment points differ, adjusting

the position of the SRCABLETRAY accessories will allow you to change the distance between attachment points. If necessary, you can use a

single ladder section instead of two sections, reducing the overall ladder length to approximately 5 feet. In addition, the assembly brackets

at the ends of the ladder sections will allow minor adjustments if you install them without pins, and you can add a few inches to the length

of the ladder by using the alternate pin holes for assembly. If the available adjustments will not accommodate the SRCABLELADDER18

accessory, you must cut one of the ladder sections. See for instructions. If the SRCABLELADDER18 Section 3.2 Ladder Modiﬁcation

accessory will ﬁt without modiﬁcation, proceed to .Section 3.3 Ladder Assembly

Note: Prior to installation, you must install the SRCABLETRAY accessory (sold separately) on each enclosure that will be linked by the SRCABLELADDER18

accessory. For ordering information, visit www.tripplite.com.

3.1 Planning

SRCABLELADDER18 can provide enclosure-to-enclosure cable routing across an aisle or within a single row. You can combine multiple

SRCABLELADDER18 and SRCABLETRAY accessories to meet the cable routing needs of almost any conﬁguration of SmartRack Enclosures,

but planning and measurement are required to ensure a secure ﬁt. Tripp Lite recommends that you read the entire manual in advance to

gain a clear understanding of the installation process and accessory positioning.

Sample Cable Routing Conﬁguration (Top View)

SRCABLETRAY

SRCABLELADDER18 installed

between enclosures across an aisle.

SRCABLELADDER18 installed

between enclosures within a row.

Specyfikacje produktu

Marka:	Tripp Lite
Kategoria:	kabel do komputerów i urządzeń peryferyjnych
Model:	SmartRack SRCABLELADDER18
Kolor produktu:	Czarny
Wysokość produktu:	50.8 mm
Szerokość produktu:	3106.4 mm
Głębokość produktu:	455.2 mm
Waga produktu:	9530 g
Szerokość opakowania:	480.1 mm
Wysokość opakowania:	85.1 mm
Głębokość opakowania:	1527 mm
Kraj pochodzenia:	Chiny
Kod zharmonizowanego systemu (HS):	7326.90.8688
Waga wraz z opakowaniem:	9780 g
Wysokość skrzyni wzorcowej (zewnętrznej):	85.1 mm
Długość skrzyni głównej (zewnętrznej):	1527 mm
Waga brutto obudowy głównej (zewnętrznej):	9780 g
Szerokość skrzyni zbiorczej (zewnętrznej):	480.1 mm
Model:	Drabina
Produkty w skrzyni głównej (zewnętrznej):	1 szt.
Dołączone śruby:	Tak
Nakrętki do bramek w zestawie:	Tak
W zestawie nakrętki:	Tak