Instrukcja obsługi Tripp Lite PDU360AT6G60

Tripp Lite Listwa zasilająca PDU360AT6G60

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Tripp Lite PDU360AT6G60 (68 stron) w kategorii Listwa zasilająca. Ta instrukcja była pomocna dla 3 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/68

1. Important Safety 2

Instructions

2. Installation 3

2.1 Mounting the ATS 3

2.2 Mounting the Power Strip 4

2.3 Connecting the Power Strip 4

to the ATS

2.4 Connecting the ATS 5

2.5 Networking the ATS 5

3. Features 6

4. Digital Display 8

5. Using the Digital Display 11

5.1 Navigating Display Menus 11

and Submenus

5.2 Navigating Conﬁg Menus 18

and Submenus

6 20. Conﬁguration and Operation

6.1 Automatic Transfer Switch 20

7. Service 22

8. Warranty and Product 22

Registration

Español 24

Français 47

Owner’s Manual

PDU360AT6G60

(Series Number: AG-013D)

3-Phase 1U Monitored Rack PDU

with Automatic Transfer Switch (ATS)

PDU3V602D354, PDU3V602D354A,

PDU3V602D354B

(Series Number: AG-013E)

3-Phase Vertical Power Strip

1111 W. 35th Street, Chicago, IL 60609 USA • www.tripplite.com/support

PROTECT YOUR INVESTMENT!

and ultimate peace of mind.

You could also win an

ISOBAR6ULTRA surge protector—

a $100 value!

www.tripplite.com/warranty

16-01-031-933588.indb 1 3/22/2016 4:14:15 PM

SAVE THESE INSTRUCTIONS

This manual contains instructions and warnings that should be

followed during the installation, operation and storage of this product.

Failure to heed these instructions and warnings may affect the

product warranty.

• The Power Strip provides the convenience of multiple outlets, but DOES NOT provide surge or

line noise protection for connected equipment.

• Use only with Tripp Lite PDU3V60XXXXX Series with overcurrent protection. Overcurrent

protection per PDU consists of six double-pole 20A, 240V AC breakers (2 per phase).

• Do not exceed the following equipment ratings:

• For Outputs 1 and 2, the maximum full balanced load is 13.9A per bank when powered by a

3-phase ATS (Automatic Transfer Switch) with a rated input of 48A.

• The Automatic Transfer Switch and Power Strip are designed for indoor use only, in a controlled

environment, away from excess moisture, temperature extremes, conductive contaminants, dust

or direct sunlight.

• Keep indoor ambient temperature between 32°F and 113°F (0°C and 45°C).

• The Automatic Transfer Switch and Power Strip must be installed by a qualified technician only.

• Do not attempt to mount the Automatic Transfer Switch or Power Strip to an insecure or

unstable surface.

• Install in accordance with National Electrical Code standards. Be sure to use the proper

overcurrent protection for the installation, in accordance with the plug/equipment rating.

• Connect the Automatic Transfer Switch to an outlet that is in accordance with your local building

codes and that is adequately protected against excess currents, short circuits and earth faults.

• The electrical outlets supplying power to the equipment should be installed near the equipment

and easily accessible.

• Do not connect the Automatic Transfer Switch to an ungrounded outlet or to extension cords or

adapters that eliminate the connection to ground.

• Be sure to provide a local disconnect device on any models that are permanently installed

without a plug that is easily accessible.

• Never attempt to install electrical equipment during a thunderstorm.

• Individual equipment connected to the Power Strip should not draw more current than the

individual outlet’s rating.

• The total load connected to the Power Strip must not exceed the maximum load rating for the

Automatic Transfer Switch.

• Do not attempt to modify the Automatic Transfer Switch’s or Power Strip’s input plugs or power

cables.

• Do not drill into or attempt to open any part of the Automatic Transfer Switch or Power Strip

housing. There are no user-serviceable parts inside.

• Do not attempt to use the Automatic Transfer Switch or Power Strip if any part of it becomes damaged.

• Use of this equipment in life support applications where failure of this equipment can reasonably

be expected to cause the failure of the life support equipment or to significantly affect its safety

or effectiveness is not recommended. Do not use this equipment in the presence of a

flammable anesthetic mixture with air, oxygen or nitrous oxide.

1. Important Safety Instructions

16-01-031-933588.indb 2 3/22/2016 4:14:15 PM

2.1 Mounting the Automatic Transfer Switch (ATS)

Mount your equipment in a 4-post rack or rack enclosure. The user must determine the fitness of

hardware and procedures before mounting. If hardware and procedures are not suitable for your

application, contact the manufacturer of your rack or rack enclosure. The procedures described in this

manual are for common rack and rack enclosure types and may not be appropriate for all applications.

Note: Each snap-in slide rail assembly consists of a sliding rack enclosure mounting bracket and an inner

channel rail. For ease of installation, the inner channel rails come pre-attached to the ATS unit.

2. Installation

1 Align the rear bracket's tabs with the rack

enclosure's square mounting holes 1A

and push the metal hooks through the

mounting holes 1B. Push the rear bracket

toward the enclosure support post in

order for the blue tabs to snap into the

mount 1A. Align the front bracket's tabs

with the rack enclosure's front square

mounting holes and push the metal

hooks through the mounting holes.

Finally, push the front bracket toward the

enclosure support post in order for the

blue tabs to snap into the mount 1B.

2 Repeat step one for the second mounting

bracket on the opposite side of the rack

enclosure.

3 Once both mounting brackets are fixed

onto the rack enclosure, secure the rear

brackets using the included M5X10L

screws.

4 Align the inner channel rails attached to

the ATS with the mounting brackets. Then

slide the unit into the rail assembly. Using

a screwdriver, secure the ATS’s panel-

mounted screws to the rack enclosure.

16-01-031-933588.indb 3 3/22/2016 4:14:16 PM

Specyfikacje produktu

Marka:	Tripp Lite
Kategoria:	Listwa zasilająca
Model:	PDU360AT6G60

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Tripp Lite PDU360AT6G60, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą

Twoje imię*

Twój email*

Napisz tutaj swoje pytanie

Instrukcje Listwa zasilająca Tripp Lite

Tripp Lite Metered PDUMH20-6 Instrukcja

21 Września 2024

Tripp Lite PDUV20-60 Instrukcja

14 Września 2024

Tripp Lite PDUH32HV Instrukcja

13 Września 2024

Tripp Lite PDU3EVS6L2130 Instrukcja

11 Września 2024

Tripp Lite PDU3XMV6G32 Instrukcja

10 Września 2024

Tripp Lite PDUMH32HVATNET Instrukcja

9 Września 2024

Tripp Lite PS480806 Instrukcja

9 Września 2024

Tripp Lite PDU3V20D354A Instrukcja

9 Września 2024

Tripp Lite NSU-G24C2P08 Instrukcja

8 Września 2024

Tripp Lite PDU3VN6H50B Instrukcja

7 Września 2024

Instrukcje Listwa zasilająca

Najnowsze instrukcje dla Listwa zasilająca

Furman Merit M-8DX Instrukcja

14 Stycznia 2025

Brennenstuhl 9+2m H07RN-F3G1,5 Instrukcja

12 Stycznia 2025

Sven SF-08E-16 Instrukcja

31 Grudnia 2025

Brennenstuhl Estilo Instrukcja

29 Grudnia 2024

Huslog EMX-190224 Instrukcja

24 Grudnia 2024

Vivanco EPLS 6ALU Instrukcja

7 Grudnia 2024

Vivanco EPLS 4USB_ALU Instrukcja

7 Grudnia 2024

Vivanco EPLS 4ALU Instrukcja

7 Grudnia 2024

Vivanco EPLS 3_1ALU2M Instrukcja

7 Grudnia 2024

Vivanco EBLS 3W2USB Instrukcja

7 Grudnia 2024