Instrukcja obsługi Trident 80B

Trident Niesklasyfikowane 80B

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Trident 80B (8 stron) w kategorii Niesklasyfikowane. Ta instrukcja była pomocna dla 5 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/8
L E G E N D A R Y E Q U A L I Z A T I O N
80B 500 Series EQ User Manual
The Equalizer
For those not familiar with the dierence
between a shelving and peaking equaliser,
the dierences are as follows. A shelving
equaliser boosts (or attenuates) all fre-
quencies equally, above or below a certain
point. The frequency specified for a shelv-
ing equaliser circuit is usually at the point
where it eectively reaches its ‘shelf’ state.
A ‘high shelf’ EQ boosts/cuts high frequen-
cies and a ‘low shelf’ type boosts/cuts low
frequencies. This type of circuit is very pop-
ular in hi-fi systems but is also actually high-
ly musical, when applied in a recording en-
vironment. In contrast, a peaking equaliser
is one that, as its name implies, has a centre
frequency that is boosted or attenuated
more than others.
The frequency range over which it reach-
es its peak and then falls down is known
as the bandwidth (or ‘Q’). Because this
type of design reaches a peak and then
falls away, it is possible with this type of
circuit to ‘home in’ on particular frequen-
cies and make adjustments without af-
fecting those around them. This can be
particularly useful when working with in-
struments such as bass guitars and snare
drums. By incorporating both shelving
and peaking equalisers into the design of
the 80B, it is possible to get the best of
both types of design.
Operating
The Equalizer
2Trident Audio Developments | 80B EQ 500 Series User Manual
Begin with all boost/cut controls - those with centre detents, set to their
mid way positions. Adjust the low and high mid frequency sweep ‘0’
controls to their minimum positions (fully anticlockwise). The 50Hz high
pass ‘Filter’ switch should be in the out position. Set the frequency select
switches controlling the high and low shelving sections, to 120Hz and
12kHz respectively. Lastly, set the ‘EQ’ switch to the ‘in’ position (the as-
sociated LED will illuminate).
3Trident Audio Developments | 80B EQ 500 Series User Manual
Operating The Equalizer
Rotation of the high frequency shelving control in a clockwise direction
emphasises high frequencies, while turning the control in an anti-clock-
wise direction from centre attenuates high frequencies.
Operating the switch in the high frequency section ‘frequency select’
introduces a subtle change of emphasis to the aected high frequencies,
as the shelving ‘knee’ is changed from 12kHz to 5kHz. Likewise, rotating
the low frequency shelving control in a clockwise direction will emphasise
low frequencies, while turning the control in an anti-clockwise direction
from centre attenuates low frequencies. Adjusting the ‘frequency select’
switch in the low section introduces a subtle change of emphasis on the
aected low frequencies by altering the shelving point from 120Hz down
to 60Hz.
The ‘low mid’ ‘high mid’ and equaliser sections are peaking filters. Adjust-
ment of their parameters is achieved by use of the boost/cut knob and
its associated frequency sweep knob. Boost or cut of a given frequency is
performed by moving that control from its centre detent position: clock-
wise for boost, anti-clockwise to cut. The frequency to be boosted or cut
is selected by the frequency sweep control knob. The range of frequen-
cies of the ‘low mid’ control extends from 100Hz up to 1.5kHz.
For the sweep, the frequency range begins at 1kHz (overlap‘high mid’ -
ping with the low mid section) and continues up to 15kHz.
The Series 80B 500 Series EQ incorporates a classic four band equalis-
er which is identical to that employed in the Trident Series 80 console.
It consists of frequency switchable high and low pass shelving sections,
coupled with two swept low and high mid range bands and a switchable
50Hz, 12dB per octave filter. Both swept midranges have been carefully
chosen for maximum eect on music programme and a good degree of
overlap is provided.
Finally, selecting the switch introduces a smooth, 50Hz, 12dB/‘Filter’
octave roll-oto eectively eliminate ‘rumble’ caused by, among other
things, someone’s feet moving about near a microphone stand, nearby
trac noise and AC systems. The amount of boost (accentuation) or cut
(attenuation) that is applied to the audio signal is entirely dependent on
the programme content and it is not our intention to advise on this. Ap-
plication of equalisation is a very subjective matter and is best learned by
experiment. The equaliser bypass switch ‘EQ’ is a useful facility for com-
paring the signal before and after the application of equalization.

Specyfikacje produktu

Marka: Trident
Kategoria: Niesklasyfikowane
Model: 80B

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Trident 80B, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje Niesklasyfikowane Trident

Trident

Trident 80B Instrukcja

29 Września 2024
Trident

Trident Series 68 Console 24 Instrukcja

27 Września 2024
Trident

Trident 68 Console 16 Instrukcja

27 Września 2024
Trident

Trident A-Range 500 Instrukcja

27 Września 2024

Instrukcje Niesklasyfikowane

Najnowsze instrukcje dla Niesklasyfikowane

Black Diamond

Black Diamond BD1121530000ALL1 Instrukcja

15 Października 2024
Husqvarna

Husqvarna K 970 SmartGuard Instrukcja

15 Października 2024
Stihl

Stihl HT 70 Instrukcja

15 Października 2024
Ernesto

Ernesto H14270 Instrukcja

15 Października 2024
Uniden

Uniden BT MIC KIT Instrukcja

15 Października 2024
Vaude

Vaude Omnis Bike 26 Instrukcja

15 Października 2024
ART

ART ProChannel II Instrukcja

15 Października 2024
Aukey

Aukey DR02J Instrukcja

15 Października 2024
Master Lock

Master Lock 653EURD Instrukcja

15 Października 2024
Roland

Roland FR-18 Diatonic Instrukcja

15 Października 2024