Instrukcja obsługi Totolink EX200

Totolink Wzmacniacz sygnału WiFi EX200

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Totolink EX200 (1 stron) w kategorii Wzmacniacz sygnału WiFi. Ta instrukcja była pomocna dla 4 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/1
For more information, please go to www.totolink.net
Product Introduction
Method One: Quick Setup by Smart Phone
FAQ(Frequently Asked Questions)
Method Two: Wi-Fi Extension by WPS Button
Power on. Plug the device into any wall
socket that near the router. Wait until the
System LED blinks slowly.
1Press WPS button on Extender for about 2 seconds.
3
SSID: TOTOLINK_EX200
The Extend LED flash when
connecting and turns to solid
light when connected
Press WPS button on your router for about 2 seconds.
2
RST/WPS
Wi-Fi: Upper router’s SSID and password
The Extend LED turns to solid light, Wi-Fi extension successful. Please refer to to place the Extender.Relocate
4
EX200's default Network Name (SSID) is TOTOLINK_EX200 (no encryption).
With success repeater connection, this SSID (TOTOLINK_EX200) will change
to the same SSID (with same encryption) of upper Router/AP. After deployment,
just connect to the Router/AP's SSID. Congratulations, you have extended your
WiFi coverage successfully.
What should I do if I cannot access the extender’s web management
page?
A1: Make sure you have connected to the wireless network name of
the extender.
A2: Open any browser, enter 192.168.0.254 in the address bar and
press Enter.
A3: Reset the extender and connect to it again.
1
How to reset the extender to factory default settings?
Keep the extender power on, use a pin to press the RST button
on the bottom of device. When both System and Extend LED blinks,
release the button. The device will restore to factory default settings.
2
Quick Installation Guide
Wireless N Range Extender
Model No.: EX200
V1.0 | 1712
Information in this document is subject to change without prior notice.
Copyrights TOTOLINK. All rights reserved. Website: http://www.totolink.net
On: The device is starting up or waiting for
extending.
Slow-blinking: The device is working normally.
Quick-flashing: The device is to restart.
Off: The device is power off.
On: Extending successfully.
-Good; -Normal; -Bad.Green Yellow Red
Slow-blinking: The device is extending to
upper Router/AP.
Quick-flashing: The device is to restart.
Off: No extending.
WPS: Press the button for about 2-3 seconds
to enable WPS.
LAN port: This port is used to connect to PC.
RST: Press the button for about 10 seconds, the
device will restore to factory default settings.
RST
Power on. Plug the device into any wall
socket that near the router. Wait until the
System LED blinks slowly.
1Connect to the Extender. Using your
smart phone to search Wi-Fi
TOTOLINK_EX200. (Settings—Wi-Fi)
2Login. The Setting page will turn up automatically.
Click . If below window doesn’tExtender Mode
appear, please open a browser and enter
192.168.0.254 manually.
3Extend Wi-Fi. Wait for a while, the Extender
auto-detects APs nearby. Choose your
router’s 2.4GHz SSID.
4 6 Verify. Check the LED status to verify
whether the Wi-Fi extension is
successful.
Configure . Enter its wireless password. Either keep
the default SSID or customize it for extended 2.4GHz
wireless network. Verify your settings and click Connect.
5
Relocate
Horizon Line
Host Network Extended Network
Vertically place the Extender
Wall Socket
Plug the extender into wall socket that halfway between your
router and the Wi-Fi dead zone. Wait about 30 seconds until
the Extend LED light turns solid green or yellow. If not, please
relocate it closer to your router to achieve better signal quality.
1
In order to make full use of extender, please keep the antennas
of the extender perpendicular to the horizontal plane. See blow:
2

Specyfikacje produktu

Marka: Totolink
Kategoria: Wzmacniacz sygnału WiFi
Model: EX200

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Totolink EX200, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje Wzmacniacz sygnału WiFi Totolink

Totolink

Totolink EX200U Instrukcja

29 Września 2024
Totolink

Totolink EX300 Instrukcja

28 Września 2024
Totolink

Totolink EX200 Instrukcja

9 Września 2024
Totolink

Totolink EX200_V2 Instrukcja

31 Sierpnia 2024
Totolink

Totolink EX1800L Instrukcja

24 Sierpnia 2024

Instrukcje Wzmacniacz sygnału WiFi

Najnowsze instrukcje dla Wzmacniacz sygnału WiFi

TP-Link

TP-Link RE220 Instrukcja

12 Stycznia 2025
Manhattan

Manhattan 525664 Instrukcja

12 Stycznia 2025
D-Link

D-Link DMG-112A Instrukcja

5 Stycznia 2025
Mercusys

Mercusys Halo H1200G Instrukcja

3 Stycznia 2025
HELGI

HELGI HLG0372 Instrukcja

2 Stycznia 2025
Medion

Medion P85032 (MD 87070) Instrukcja

30 Grudnia 2025
TP-Link

TP-Link RE3000X Instrukcja

30 Grudnia 2025
Hawking Technologies

Hawking Technologies HOW2R1 Instrukcja

14 Października 2024
Planet

Planet WNAP-1110 Instrukcja

10 Października 2024
Netgear

Netgear WN2000RPTv2 Instrukcja

10 Października 2024