Instrukcja obsługi Total TS730301

Total Maszyna do piłowania TS730301

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Total TS730301 (18 stron) w kategorii Maszyna do piłowania. Ta instrukcja była pomocna dla 2 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/18
BAND SAW
Security instructions
Caution
Read all safety warnings and all instructions. Failure to follow the warnings and
instructions may result in electric shock, fire, and/or serious injury. This manual must
accompany the equipment at all times and must be kept in a safe place to be available.
Note: Save all warnings and instructions for future reference. Due to our ongoing R&D&I program,
the specifications in this document are subject to change without notice.
1) Work area safety
a. Keep the work area clean and well lit to prevent accidents.
b. Do not use power tools in explosive atmospheres, such as in the presence
of flammable liquids, gases, or dust that can cause fires.
c. Keep children and other unauthorized persons away while using a power
tool. Distractions can cause you to lose control of the tool.
2) electrical safety
a. Power tool plugs must match the outlet. Never modify the plug in any way.
Using a suitable plug reduces the risk of electric shock.
b. Avoid bodily contact with grounded surfaces such as pipes, radiators,
ranges, and refrigerators. There is an increased risk of electric shock if
your body is grounded.
c. Do not expose power tools to rain or wet conditions. Water entering a
power tool will increase the risk of electrical shock.
d. Never use the cord to carry, pull or unplug the power tool. Keep the cable
away from heat or oil.
e. When using a power tool outdoors, use an extension cord suitable for
outdoor use.
f. If using the tool in a damp location is unavoidable, use a Residual Current
Device (RCD) protected supply to reduce the risk of electric shock.
3) Personal security
a. Always stay alert, watch what you are doing and use common sense
when using the tool.
b. Do not use a power tool if you are tired or under the influence of
medication or other substances.
c. Wear personal protective equipment. Always wear eye protection.
Protective equipment such as a dust mask, non slip safety shoes, hard -
hat, or hearing protection used in the proper conditions will reduce
personal injury. Also don't wear loose clothing or jewelry.
d. Prevent the tool from turning on unintentionally. Make sure the switch is
in the off position before connecting to power source and moving.
e. Remove any adjusting wrenches or wrenches before turning on the power
tool. An adjustable wrench or wrench placed in a rotating part of the power
tool can cause serious injury.
f. If devices are used for dust extraction and collection, make sure they are
properly connected. Properly use these devices and you will reduce dust-
related hazards.
4) Use and care of power tools
a. Do not force the tool. Use the correct power tool for each use.
b. Do not use the power tool if its power switch does not work. Any power
tool that cannot be controlled with the switch is dangerous and must be
repaired.
c. Disconnect the plug from the power source before making any
adjustments, changing accessories, or storing the tool to avoid accidental
starting of the tool.
d. Use the power tool, accessories and bits etc. in accordance with these
instructions, taking into account the working conditions and the work to
be carried out. Using the power tool for operations other than those
intended could result in a hazardous situation.
e. Store power tools out of the reach of children and do not allow people
unfamiliar with the tool to use it.
f. Keep power tools. Check for misalignment or binding of moving parts,
breakage of parts, and any other conditions that may affect the operation
of power tools. If it is damaged, have the power tool repaired before using
it. Many accidents are caused by poorly maintained power tools.
g. Keep cutting tools sharp and clean. Properly maintained cutting tools with
sharp cutting edges are less likely to bind and are easier to control.
5) vice Ser
a. Have your power tool serviced by a qualified person and use replacement
parts recommended by the manufacturer. This will ensure that the safety
of the power tool is maintained.
Additional security warnings
To use this equipment correctly, you must observe the safety regulations, assembly and
operation instructions in this manual.
All those people who use and repair the machine must be familiar with the manual and
informed of occupational hazards. Children and untrained persons may not use the
machine. In addition, these people must be outside the work area.
It is essential to observe the accident prevention regulations and apply them in the area
where the equipment is to be used. The same applies to occupational health and safety
regulations and rules.
Caution
Whenever you use a power tool, follow safety precautions to reduce the risk of fire,
electric shock, and injury to persons. It is also necessary to take into account the advice
contained in the safety instructions section.
The machine must be used under all prescribed start up and safety instructions, but -
bearing in mind that it is not possible to eliminate all risk factors. The following risks may
arise during the assembly and use of the machine:
• Contact with the cutting blade or fracture thereof.
• Hearing damage or the like if you do not use adequate protection.
• Harmful emissions of sawdust when the equipment is used inside closed areas
without ventilation. Always use dust extractors and dust extraction.
• Always unplug the power cord before making any adjustments or maintenance
to the equipment, including changing the blade.
Safety is a combination of common sense, staying alert, and knowing how your band
saw works.

Specyfikacje produktu

Marka: Total
Kategoria: Maszyna do piłowania
Model: TS730301

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Total TS730301, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje Maszyna do piłowania Total

Total

Total TJSLI8501 Instrukcja

17 Grudnia 2024
Total

Total TS730301 Instrukcja

17 Grudnia 2024

Instrukcje Maszyna do piłowania

Najnowsze instrukcje dla Maszyna do piłowania

Herkules

Herkules KS 210 Profi Instrukcja

17 Grudnia 2024
Global

Global PSL-G 750 Instrukcja

16 Grudnia 2024
Global

Global N-PSL 750 Instrukcja

16 Grudnia 2024
Global

Global MTS-G 400 Instrukcja

16 Grudnia 2024
Global

Global PSG 750 Instrukcja

16 Grudnia 2024
Turbo-Silent

Turbo-Silent EKS 2040/1 Instrukcja

16 Grudnia 2024
King Craft

King Craft ZKGS 4300 UG Instrukcja

15 Grudnia 2024
Fieldmann

Fieldmann FZP 5816-B Instrukcja

13 Grudnia 2024
Fieldmann

Fieldmann FZP 4216-B Instrukcja

13 Grudnia 2024
Fieldmann

Fieldmann FDP 200805-E Instrukcja

13 Grudnia 2024