Instrukcja obsługi Toddy Pro Series 10

Toddy Koffiezetapparaat Pro Series 10

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Toddy Pro Series 10 (2 stron) w kategorii Koffiezetapparaat. Ta instrukcja była pomocna dla 4 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/2
bridge handle
Water
level
COLD BREW SYSTEM - PRO SERIES v2
ToddyCafe.com/Brewing | ©2021 Toddy, LLC All rights reserved.
Step 1 Install valve assembly so the handle
points away from the system when the valve is
open. Tip: To turn the valve handle, pull out on
the handle. Close the valve completely. Set aside
the cleaning blank.
Step 2 Slide the platform into a new filter, and
fold as indicated above. Holding the bridge handle
insert the platform and filter, guiding the platform
into place until it rests on the support ring.
Step 3 Slowly add filtered water to about 1
inch (2.5 centimeters) above the platform and
filter. This is 3 gallons (or 11 liters) in a Pro
Series 10 and 6 gallons (or 22 liters) in a Pro
Series 20.
Step 4 When adding water, air may get
trapped in the filter. If the filter bubbles up,
gently guide the paddle across the platform
toward the open end to push the air out, taking
care not to tear the filter.
Step 5 Add half of the ground coffee on top of
the platform and filter. Next, add half of the
remaining filtered water (half of what's left after
the initial fill in step 3), pouring evenly to
saturate all the grounds.
Step 6 Carefully stir with the mixing paddle,
avoiding contact with the filter. Repeat step 5 to
add the rest of the coffee and filtered water. Then
place the lid on the brewer. Tip: For best results,
mix coffee grounds by pulling and plunging them
from the edge of the brewer toward the center.
Add half
remaining
water
12 3
465
Step 7 Break the crust and stir again after
30 minutes to release trapped gas and to make
sure all grounds are evenly saturated. This is an
important step to ensure proper extraction.
Step 8 Put the lid back on and allow to brew at
room temperature for 8 to 24 hours, depending
on your preferred flavor profile.
Step 9 Once brewing is complete, attach one
end of the hose to the hose barb and place the
other end into a clean storage vessel. Open the
valve to drain your cold brew coffee extract.
Once draining is complete, refrigerate extract in
airtight containers for up to 2 weeks.
8
-
24hwait 30 min
7 98
Brewing Guide
BREWER SIZE
PRO SERIES 10
PRO SERIES 20
GROUND COFFEE
10 LBS (4.5KG)
20 LBS (9KG)
FILTERED WATER
7 GAL (26.5L)
14 GAL (53L)
Metric equivalents are rounded for convenience.
For video tutorials and more information, please scan the QR Code below or visit ToddyCafe.com/Brewing
Turn handle to
the right 90˚
to open valve
Turn handle to left
90˚ to close valve
Tuck front of filter
behind platform
Fold back of filter over
to the front of platform
Please wash all
reusable parts
before first use.
Inner support ring
Version: 11-2021
Serve:
This recipe yields a concentrated extract, which can be diluted to suit your cold brew
application. Visit ToddyCafe.com/Brewing for more recipes and serving ideas.
BREWER SIZE
PRO SERIES 10
PRO SERIES 20
TODDY® CLEANER
2 scoops (80g, cup, 2.8oz)1/3
4 scoops (160g, 2/3 cup, 5.6oz)
ToddyCafe.com/Brewing | ©2021 Toddy, LLC All rights reserved.
Version: 11-2021
12 3
465
Step 1 Using a , invert the brewer over team lift
a waste or compost bin to remove all coffee
grounds and filter platform.
Step 2 Remove the platform from the filter.
Thoroughly rinse the brewer and all parts. Note:
Pro Series filters are compostable.
Step 3 Remove the valve and attach cleaning
blank to the flange using a clean gasket and a
tri-clamp.
Step 4 Add 2 to 3 liters of hot water to the
brewer, then add Toddy® Cleaner per the chart
below. Allow the solution to fully dissolve.
Step 5 Place all components including the
valve assembly, gasket, hose barb, hose, and
tri-clamp into the bottom of the unit below the
platform to ensure they are fully submerged.
Clean with the valve in the open position.
Step 6 Add the paddle and fill with warm
water, nearly to the top of the brewer.
Step 7 Hang the lid on one of the handles.
Wipe lid and paddle handle with a clean towel
dipped in cleaning solution. Let solution soak for
at least 60 minutes.
Step 8 Remove the tri-clamp and cleaning
blank over the sink, drain solution from the
brewer, and allow all parts to air dry. (Do not dry
with a towel.)
Step 9 For extra shine, polish the exterior with
a soft microfiber cloth and warm water.
Cleaning
7 98
60min

Specyfikacje produktu

Marka: Toddy
Kategoria: Koffiezetapparaat
Model: Pro Series 10

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Toddy Pro Series 10, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje Koffiezetapparaat Toddy

Toddy

Toddy Pro Series 10 Instrukcja

18 Września 2024

Instrukcje Koffiezetapparaat

Najnowsze instrukcje dla Koffiezetapparaat

Philips

Philips HD7411 Instrukcja

9 Października 2024
Royal Catering

Royal Catering RCCCM-022TM Instrukcja

9 Października 2024
Cecotec

Cecotec Cremmaet Compact Steam Instrukcja

9 Października 2024
Tower

Tower T13005 Instrukcja

8 Października 2024
Smeg

Smeg BCC11 Instrukcja

8 Października 2024
Muse

Muse MS-220 BC Instrukcja

8 Października 2024
Muse

Muse MS-220 DG Instrukcja

8 Października 2024
Sencor

Sencor SES 8000BK Instrukcja

8 Października 2024
Sencor

Sencor SES 9350CH Instrukcja

8 Października 2024
Sencor

Sencor SES 4910SS Instrukcja

8 Października 2024