Instrukcja obsługi TOA WTU-M9800

TOA Niesklasyfikowane WTU-M9800

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla TOA WTU-M9800 (9 stron) w kategorii Niesklasyfikowane. Ta instrukcja była pomocna dla 2 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/9
INSTRUCTION MANUAL
WIRELESS TUNER MODULE WTU-M9800
Thank you for purchasing TOA’s Wireless tuner module.
Please carefully follow the instructions in this manual to ensure long, trouble-free use of your equipment.
1. SAFETY PRECAUTIONS
• Be sure to read the instructions in this section
carefully before use.
• Make sure to observe the instructions in this manual
as the conventions of safety symbols and messages
regarded as very important precautions are included.
• We also recommend you keep this instruction
manual handy for future reference.
When Installing the Unit
• Do not expose the unit to rain or an environment
where it may be splashed by water or other liquids,
as doing so may result in fire or electric shock.
When Installing the Unit
• Do not mount the module in equipment other than
those designated.
• Use only with the voltage specified on the module.
Using a voltage higher than that which is specified
may result in fire or electric shock.
• Be sure to turn off the power of the equipment
before installing the module.
• Avoid touching parts and terminals on the module’s
circuit board when inserting or removing the module.
Caution to the user
Notice:
The changes or modifications not expressly approved
by the party responsible for compliance could void the
user’s authority to operate the equipment.
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference,
and
(2) this device must accept any interference received,
including interference that may cause undesired
operation.
IMPORTANT NOTE
This device contains license-exempt
transmitter(s)/receiver(s) that comply with Innovation,
Science and Economic Development Canada’s
license-exempt RSS(s). Operation is subject to the
following two conditions:
(1) This device may not cause interference.
(2) This device must accept any interference, including
interference that may cause undesired operation of
the device.
L’émetteur/récepteur exempt de licence contenu dans
le présent appareil est conforme aux CNR d’Innovation,
Sciences et Développement économique Canada
applicables aux appareils radio exempts de licence.
L’exploitation est autorisée aux deux conditions
suivantes :
(1) l’appareil ne doit pas produire de brouillage;
(2) l’utilisateur de l’appareil doit accepter tout
brouillage radioélectrique subi, même si le brouillage
est susceptible d’en compromettre le
fonctionnement.
2. GENERAL DESCRIPTION
The TOA WTU-M9800 Wireless Tuner Module is designed for plugged into the 9000 series, 900 series and TOA’s
other equipment. It is used in conjunction with UHF wireless equipment for vocal or speech reinforcement
applications. Its built-in circuit minimizes the influence of ambient noise
3. FEATURES
• An optimized PLL-synthesizer drastically minimizes the oscillation frequency drift resulting from the ambient
temperature changes.
• A contact output terminal is provided for control of external equipment.
4. HANDLING PRECAUTION
• Be sure to connect at least two receiving antennas (one each for Antenna A and B).
CAUTION Indicates a potentially hazardous
situation which, if mishandled, could result in moderate or
minor personal injury, and/or property damage.
2
5. NOMENCLATURE
1. Antenna input A, B
75 , BNCΩ
When external antennas are not required, use the supplied two rod antennas,
which should be set at a 45° angle from vertical. If external antennas are
required, please use the optional YW-4500 powered antenna.
2. Reception lamps
Either lamp of A (left) or B (right) lights green when the tuner module receives a
radio signal.
3. Channel selector switch
Set the receiving channel.
4. Contact output terminal
Push-type terminal block. CC is closed when unit receives RF from the
transmitter
5. DC input jack (* External power supply mode only)
Connect the power cable of the optional AC adapter to this jack. Make sure
internal jumper settings are correct.
6. Jumper connector for power supply mode select
Select the internal or external power supply mode.
6. CONNECTION
6.1. Plug-in module insertion
Step 1. Remove the blank panel covering the module slot on
the rear panel of the equipment.
Step 2. Align the module board with the top and bottom
guide rails, and press in.
Step 3. Using the screws supplied with the module, secure
the module to the rear panel.
6.2. Connection example
Be sure to connect at least two receiving antennas (one each for Antenna A and B).
1
3
4
5
2
or
Accessory
Wall-mounted
wireless antenna
YW-4500 (option)
AC adapter or
equivalent power
supply source *
* External power
supply mode only
3
6.3. External power supply mode
The WTU-M9800 module has 2 power supply modes.
One is the internal 24V mode which is supplied from the power supply of the equipment, and other one is the
external mode which is supplied from an optional AC adapter.
Move the jumper to select the correct power mode as shown below.
When using up to two WTU-M9800 in the same frame, the frame’s internal power supply may be used.
When using three or more WTU-M9800 in the same frame, each unit must be externally powered.
Note: a WD-5800 antennal distributor will consolidate antennas and power supplies for easier installation.
6.4. Contact output
The WTU-M9800 module features a no-voltage contact closure output, which can be used to control external
equipment.
The contact output is enabled when a tuner senses that its transmitter is powered on. There is a one second delay
between the microphone turning off and the contact closure opens.
7. OPERATION
Step 1. Set the channel selector switch to the predetermined channel number using the small screwdriver supplied
with the WTU-M9800.
1 second
Microphone ON Microphone OFF Microphone OFF
Contact output
disenabled
Contact output
enabled
Contact output
disenabled
Internal power supply mode
External power supply mode
or or
DC power
distribution port
from WD-5800
or
AC adapter
Internal power supply mode
External power supply mode

Specyfikacje produktu

Marka: TOA
Kategoria: Niesklasyfikowane
Model: WTU-M9800

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z TOA WTU-M9800, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje Niesklasyfikowane TOA

TOA

TOA HY-WM7W Instrukcja

11 Grudnia 2024
TOA

TOA ST-34B Instrukcja

9 Października 2024
TOA

TOA PJ-304 Instrukcja

8 Października 2024
TOA

TOA PE-604 Instrukcja

8 Października 2024
TOA

TOA SC-630TU Instrukcja

7 Października 2024
TOA

TOA SR-SA4 Instrukcja

7 Października 2024
TOA

TOA ST-800 Instrukcja

7 Października 2024
TOA

TOA HY-TM7B-WP Instrukcja

3 Października 2024
TOA

TOA RM-300X Instrukcja

26 Września 2024
TOA

TOA TS-922 Instrukcja

26 Września 2024

Instrukcje Niesklasyfikowane

Najnowsze instrukcje dla Niesklasyfikowane

GBC

GBC ThermaBind T500Pro Instrukcja

15 Stycznia 2025
Da-Lite

Da-Lite Parallax 29850 Instrukcja

15 Stycznia 2025
Crivit

Crivit IAN 290909 Instrukcja

15 Stycznia 2025
Tripp Lite

Tripp Lite SmartRack SRW12US Instrukcja

15 Stycznia 2025
Powerfix

Powerfix IAN 280221 Instrukcja

15 Stycznia 2025
AGM

AGM Rattler TC35-640 Instrukcja

15 Stycznia 2025
AGM

AGM Wolf-7 Pro Instrukcja

15 Stycznia 2025
AGM

AGM Anaconda TC50-640 Instrukcja

15 Stycznia 2025
AGM

AGM Secutor Pro TS50-640 Instrukcja

15 Stycznia 2025
Microchip

Microchip AT91SAM9M11 Instrukcja

15 Stycznia 2025