Instrukcja obsługi Tiptel Snom DECT repeater

Tiptel Wzmacniacz sygnału WiFi Snom DECT repeater

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Tiptel Snom DECT repeater (3 stron) w kategorii Wzmacniacz sygnału WiFi. Ta instrukcja była pomocna dla 3 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/3
snom m3 DECT Range Repeater
A repeater is used when you need to extend
the range of your cordless DECT telephone to
include areas where reception was previously not
available.
The DECT Range Repeater is especially suited
to be used together with the snom m3.
Simply follow the Auto registration
guide.
All the usual mobile unit functions except for firm-
ware update and central phone book are supported
by the base station in this extended radio range.
The repeater and base station have wireless
connections with each other, just as the repeater
and handset have wireless connections. Signals
are exchanged without the user hearing or
noticing the difference.
System with multiple repeaters
Up to 6 repeaters can be registered at a base
station. The number of mobile units to be
operated only depends on the type of the base
station installed.
All repeaters must be installed within the
base stations c erage area, as shown in the ov
drawings.
The repeaters can be used to extend the
coverage area in all directions - including up and
down (e.g. to c er severov al floors in a building).
If the repeaters are placed correctly (overlapping
the coverage area of the base station), you
can go from one area (cell) to the other while
speaking on the mobile unit.
The mobile unit will automatically switch from
cell to cell without this being noticed during the
telephone call.
Before the repeater is installed, it must be
registered to the base station.
The repeater can be registered to a base station
in two ways, automatic or manual registration.
Auto registration
1. Ensure that the repeater is switched off
(disconnect the power plug).
2. Set the base station in registration mode.
On most base stations, the procedure is
started by holding down the “Registration” or
“Page” key for several seconds. Consult your
base station user guide for more information.
For the snom m3
, press the key on RESET
the base station.
3. Switch on the repeater (connect the power
plug).
4. The LED on the repeater flashes. After a short
while the LED stays on permanently indicating
that registration is complete and the unit is
ready for operation.
Note! If the registration is not immediately
successful, the LED will flash continuously. In this
case, repeat the procedure.
Note! Before reinstalling the repeater (e.g. at
another base station), please reset the repeater
beforehand as described below:
– Switch off the unit (disconnect the power
plug).
– Switch on for 1 to 5 seconds and switch off
again.
– Switch on for 25 to 35 seconds and switch it
off again.
Now the repeater is ready for a new auto
registration.
Manual registration
The repeater registration procedure varies
depending on the base station installed. The base
station, a mobile unit (handset) and the repeater
must be accessible before registration can be
performed. If you are connecting more than
one repeater, registration must be performed
separately for each repeater.
Preparations
The base station and a mobile unit should be
ready for operation, the repeater must be not yet
connected to the main supply.
The following procedure is also shown as a quick
guide on the back of this user manual.
1. Set the repeater in registration mode. Insert
the repeaters power plug for 1-5 seconds
in the socket and then remove it. Insert it
once more and leave it there. The LED on
the repeater flashes slowly after the start.
You now hav ve minutes to carry out the e fi
registration. If the procedure is not carried out
within this period you must start over again.
2. Set the base station in registration mode.
On most base stations, the procedure is
started by holding down the “Registration” or
“Page” key for several seconds. Consult your
base station user guide for more information.
3. The LED on the front of the repeater flashes.
very quickly without If the LED flashes
interruptions go to step 5. If the LED flashes
very quickly with brief interruptions go to step
4.
4. Registration of the handset:
If the base code has been changed, it must
be set to “0000”. You must repeat the
registration procedure even if the mobile
unit used was already registered at the base
station, (consult your base station user guide
for more information). Now the LED flashes
very quickly without interruptions.
5. Assign a repeater number:
You must now assign a repeater number
to the repeater (selection: 2-7, for up to 6
repeaters).
Please note that each number can only be
assigned once, when using more than one
repeater. These numbers are independent of
the mobile unit extension numbers.
Hook off by pressing the -key (the LED
stops flashing). Press a number between
2 and 7. When the repeater has accepted
the chosen number, the LED will flash a
corresponding number of times. Accept the
registration by pressing the
*-key and then
the hook-on key. The repeater is now
automatically restarted. The LED goes off for
2 seconds, flashes for a brief moment and the
LED remains continuously illuminated.
The registration of the repeater is completed.
You can now disconnect the power and
move the repeater to the selected location
(disconnecting the power will not delete the
registration.)
Placement
To get the best operation conditions for the
repeater, it is important to place it correctly.
Here are a few tips for placing of repeaters:
• Choose a raised position with a good base
station reception.
• When positioning you should oid obstacles av
that can interfere with a radio transmission,
such as thick walls, radiators etc.
• You should oid interference from other av
electrical appliances, such as micro-wave
ovens, hi-fi equipment, computers etc. close
to an electric socket.
• A distance of minimum 10 meters should be
observed when installing two repeaters in an
overlapping reception range.
To find the best possible location for the repeater,
you h e to try different locations. Establish av
a call and walk around with the handset to
determine the base stations coverage area. You
can install the repeater at a location, in the edge
of the c erage area, where you still have a ov
good connection between the handset and the
base station. A new coverage area will now be
available around the repeater.
Note: The LED must remain on constantly after
the device has been switched on.
If the LED flashes, the repeater is too far away
from the base station or reception is being
hindered by thick walls or metal objects (e.g.
radiators)
Verification tone
The v you to establish erification tone enables
whether or not the mobile unit is working in
the extended area of the repeater. This tone is
audible on the activated mobile unit as long as
the unit is connected to the repeater.
Carry out the procedure described below on your
repeater in order to switch the verification tone
on and off:
– Switch off the repeater (disconnect the power
plug)
– Switch on for 1-5 seconds and switch it off
again.
– Switch on again. The LED on the repeater is
flashing slowly, switch off again.
– Switch it on again. The verification tone is
then activated or deactivated.
Maintenance
Simply wipe the repeater with a damp cloth or an
antistatic wipe. Never use solvents or a dry cloth
(static discharge).
snom DECT repeater
User manual
Auto registration Manual registration
Base station
Switch on
Repeater
Switch on/off
Switch on again
Base station
Press registration/reset key
Repeater
Quick flashing
No interruptions
Handset
Registration of handset
PIN = 0000 Ref. user manual
Handset
Hook off -key
Repeater
LED steady on
Handset
Enter RPN-No. between 2 & 7
Handset
Press *
Hook on -key
Ready for use
Repeater
Quick flashing with brief
interruptions
Repeater
Quick flashing
no interruptions
Base station
Switch on
Base station
Repeater
Switch on
Repeater
LED flashes
Repeater
LED steady on
Ready for use
No
Yes
This appliance is labelled in accordance with
European directive 2002/96/EC concerning
used electrical and electronic appliances (waste
electrical and electronic equipment - WEEE).
The guideline determines the framework for
the return and recycling of used appliances as
applicable throughout the EU. Please ask your
dealer about current means of disposal.
EEC Directive No. 91/263 and No. 93/68snom technology AG · Charlottenstraße 68-71 · 10117 · Germany · Berlin man_snomDECTrepeater_102_en
Notice: The DECT Range Repeater does not
work with all base models. Please ask your local
dealer for clarification.
www.snom.com
Press registration/reset key

Specyfikacje produktu

Marka: Tiptel
Kategoria: Wzmacniacz sygnału WiFi
Model: Snom DECT repeater

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Tiptel Snom DECT repeater, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje Wzmacniacz sygnału WiFi Tiptel

Tiptel

Tiptel Snom DECT repeater Instrukcja

11 Września 2024

Instrukcje Wzmacniacz sygnału WiFi

Najnowsze instrukcje dla Wzmacniacz sygnału WiFi

Hawking Technologies

Hawking Technologies HOW2R1 Instrukcja

14 Października 2024
Planet

Planet WNAP-1110 Instrukcja

10 Października 2024
Netgear

Netgear WN2000RPTv2 Instrukcja

10 Października 2024
Xiaomi

Xiaomi RA75 Instrukcja

9 Października 2024
Cudy

Cudy RE3000 Instrukcja

8 Października 2024
Cudy

Cudy RE1200 Instrukcja

8 Października 2024
Netgear

Netgear EX6170 Instrukcja

8 Października 2024
Extron

Extron FOX 3G HD-SDI SM Instrukcja

8 Października 2024
Extron

Extron FOXBOX Rx VGA MM Instrukcja

8 Października 2024
Extron

Extron FOX 3G HD-SDI P SM Instrukcja

8 Października 2024