Instrukcja obsługi Tecmate Optimate 4 TM 242 Accu oplader

Tecmate Ładowarka baterii Optimate 4 TM 242 Accu oplader

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Tecmate Optimate 4 TM 242 Accu oplader (44 stron) w kategorii Ładowarka baterii. Ta instrukcja była pomocna dla 11 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/44
INSTRUCTIONS FOR USE
IMPORTANT: Read completely
before charging
MODE D’EMPLOI
IMPORTANT: à lire avant
d’utiliser l’appareil
ANWENDUNGSVORSCHRIFTEN
WICHTIG: Vollständig vor der
Benutzung lesen
GEBRUIKSAANWIJZING
BELANGRIJK: Lees volledig voor
gebruik
MODO DE EMPLEO
IMPORTANTE: a leer antes de
utilizar el aparato
INSTRUÇÕES DE UTILIZAÇÃO
IMPORTANTE: Ler antes de
utilizar.
ISTRUZIONI PER L’USO
IMPORTANTE: da leggere prima
di utilizzare l’apparecchio
INSTRUKTIONER
VIKTIGT: läs följande fullständiga
instruktioner för användningen
innan du använder laddaren
Automatic charger for 12V lead/acid batteries • Chargeur automatique pour
batteries 12V plomb-acide • Cargador automático para baterías 12V
plomo-ácido • Carregador automático para baterias de 12V chumbo/ácido •
Automatische Ladegerät für 12V Blei-Säure Batterien • Automatische lader
voor 12V loodzuur accu’s • Caricabatterie automatico per batterie 12V
piombo-acido • Automatisk diagnostisk laddare för 12V blybatterier
1 x 12V
STD / AGM-MF / GEL
3 - 50Ah (charge within 48 hours), up
to 70Ah for long term maintenance
+-
MODEL: TM240, TM242, TM246
AC: 100-240VAC 50-60Hz
0,27A @ 100Vac – 0,15A @ 240Vac
DC: 0,8A 12V
TEST
VOLTS 0 12,2 12,4 12,5 12,7
STD
GEL
AGM / MF
61-80%
40-60% 61-80%
61-80%
61-80%
61-80%
61-80%
40-60%
40-60%
Test battery at connection / Automatic hourly test during long term maintenance
10 sec.
2. 5.3.1. 4.
Change program: Standard CAN-bus
FINAL
TURBO
DUAL PROGRAM
F
F
F
F
77
10
9
8
3
.1
3
.2
4
.1
4
.2
66
55
2
1
3
.3
LED indications (illustration 1)
Early warning of battery problems (illustration 2)
Change program (illustration 3)
3
™
AUTOMATIC DIAGNOSTIC CHARGER FOR 12V LEAD-ACID BATTERIES
FROM 3Ah TO 50Ah, AS FOUND IN:
DO NOT USE FOR NiCd, NiMH, Li-Ion OR NON-RECHARGEABLE BATTERIES.
Input: 100-240V maximum 0,27A. The maximum output current is 0,8A.
IMPORTANT: READ THE FOLLOWING INSTRUCTIONS BEFORE USING THE CHARGER
This appliance is not intended for use by persons (including children) with reduced physical, sensory or
mental capabilities, or lack of experience and knowledge, unless they have been given supervision or
instruction concerning use of the appliance by a person responsible for their safety. Children should be
supervised to ensure that they do not play with the appliance.
SAFETY WARNING AND NOTES: Batteries emit EXPLOSIVE GASES - prevent fl ame or sparks near batteries. Disconnect AC
power supply before making or breaking DC/battery connections. Battery acid is highly corrosive. Wear protective clothing and
eyewear and avoid contact. In case of accidental contact, wash immediately with soap and water. Check that the battery posts are
not loose; if so, have the battery professionally assessed. If the battery posts are corroded, clean with a copper wire brush; if greasy
or dirty clean with a rag damped in detergent. Use the charger only if the input and output leads and connectors are in good,
undamaged condition. If the input cable is damaged, it is essential to have it replaced without delay by the manufacturer, his
authorised service agent or a qualifi ed workshop, to avoid danger. Protect your charger from acid and acid fumes and from damp
and humid conditions both during use and in storage. Damage resulting from corrosion, oxidation or internal electrical short-
circuiting is not covered by warranty. Distance the charger from the battery during charging to avoid contamination by or exposure
to acid or acidic vapours. If using it in the horizontal orientation, place the charger on a hard, fl at surface, but NOT on plastic, textile
or leather. Use the fi xing holes provided in the enclosure base to attach the charger to any convenient, sound vertical surface.
EXPOSURE TO LIQUIDS: This charger is designed to withstand exposure to liquids accidentally spilled or splashed onto the
casing from above, or to light rainfall. Prolonged exposure to falling rain is inadvisable and longer service life will be obtained by
minimizing such exposure.Failure of the charger due to oxidation resulting from the eventual penetration of liquid into the electronic
components, connectors or plugs,is not covered by warranty.
BATTERY CONNECTIONS: 2 interchangeable connection sets are available, supplied with the charger is a set of battery clips for
charging the battery off-vehicle, the other connection set comes with metal eyelet lugs for permanent connection to the battery
posts, and re-sealable weatherproof cap on the connector that connects to the charger output cable. This connection set allows easy
and sure connection of the charger to maintain the battery on-vehicle. The resealable weatherproof cap is designed to protect the
connector from dirt and damp whenever the charger is not attached. Consult a professional service agent for assistance in attaching
the metal eyelets to the battery posts. Secure the connector with weatherproof cap so that it cannot foul any moving part of the
vehicle or the cable can be pinched or damaged by sharp edges. The in-line fuse in the eyelets connection set protects the battery
against such accidental shorting across positive and negative conductors. Replace any burnt fuse only with a similar new fuse of
15A rating.
CONNECTING THE CHARGER TO THE BATTERY
1. Disconnect AC power supply before making or breaking DC / battery connections.
2. If charging a battery in the vehicle with the battery clips, before making connections, fi rst check that the battery clips can be
safely and securely positioned clear from surrounding wiring, metal tubing or the chassis. Make connections in the following
order: First connect to the battery terminal not connected to the chassis (normally positive), then connect the other battery clip
(normally negative) to the chassis well away from the battery and fuel line. Always disconnect in reverse sequence.
3. When charging a battery out of the vehicle with the battery clips, place it in a well ventilated area. Connect the charger to the
battery: RED clamp to POSITIVE (POS, P or +) terminal and BLACK clamp to NEGATIVE (NEG, N or –) terminal. Make sure the
connections are fi rm and secure. Good contact is important.
4. If the battery is deeply discharged (and possibly sulfated), remove from the vehicle and inspect the battery before
connecting the charger for a recovery attempt. Visually check the battery for mechanical defects such as a bulging or
cracked casing, or signs of electrolyte leakage. If the battery has fi ller caps and the plates within the cells can be seen from the
outside, examine the battery carefully to try to determine if any cells seem different to the others (for example, with white
matter between the plates, plates touching). If mechanical defects are apparent do not attempt to charge the battery, have the
battery professionally assessed.
5. If the battery is new, before connecting the charger read the battery manufacturer’s safety and operational instructions
carefully. If applicable, carefully and exactly follow acid fi lling instructions.
SAFETY

Specyfikacje produktu

Marka: Tecmate
Kategoria: Ładowarka baterii
Model: Optimate 4 TM 242 Accu oplader

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Tecmate Optimate 4 TM 242 Accu oplader, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje Ładowarka baterii Tecmate

Tecmate

Tecmate OPTIMATE 5 TM 221 Instrukcja

28 Września 2024
Tecmate

Tecmate Optimate 5 Voltmatic - TM222 Instrukcja

28 Września 2024
Tecmate

Tecmate OPTIMATE 5 TM 220 Instrukcja

28 Września 2024
Tecmate

Tecmate Optimate Lithium - TM290 Instrukcja

28 Września 2024
Tecmate

Tecmate Optimate 3+ Instrukcja

28 Września 2024
Tecmate

Tecmate Optimate Lithium - TM291 Instrukcja

28 Września 2024
Tecmate

Tecmate ACCUMATE PRO Instrukcja

28 Września 2024
Tecmate

Tecmate ACCUMATE Instrukcja

28 Września 2024
Tecmate

Tecmate Optimate Pro 2 Instrukcja

28 Września 2024
Tecmate

Tecmate ACCUMATE PRO 5 Instrukcja

28 Września 2024

Instrukcje Ładowarka baterii

Najnowsze instrukcje dla Ładowarka baterii

MSW

MSW S-CHARGER-20A.2 Instrukcja

15 Października 2024
MSW

MSW S-CHARGER-10A.2 Instrukcja

15 Października 2024
Intenso

Intenso Powerbank 10400 Instrukcja

14 Października 2024
Gembird

Gembird CHM-03 Instrukcja

10 Października 2024
Kostal

Kostal IQ 8.5 Instrukcja

9 Października 2024
Venom

Venom VS5007 Instrukcja

9 Października 2024
Venom

Venom VS5010 Instrukcja

9 Października 2024
Venom

Venom VS2891 Instrukcja

9 Października 2024
Venom

Venom VS2881 Instrukcja

9 Października 2024
Venom

Venom VS2883 Instrukcja

9 Października 2024