Instrukcja obsługi Techly I-CASE TRAY-ORG800

Techly Nie skategoryzowane I-CASE TRAY-ORG800

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Techly I-CASE TRAY-ORG800 (2 stron) w kategorii Nie skategoryzowane. Ta instrukcja była pomocna dla 4 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Strona 1/2
WWW.TECHLY.COM
CABLE MANAGEMENT TRAY
USER'S
MANUAL
INTRODUCTION
This rack cable management system is a smart solution for tidying up cables and neatly managing
cabling inside a 19” rack.
Ideal for keeping the wiring tidy and clean, essential for checking and replacing the cables.
FUNCTION DESCRIPTION
Clear identification:
With layer identification, connection relationship identification, line direction identification
INSTALLATION AND OPERATION INSTRUCTIONS
Item Name Picture Qty Remark
Cable
Management
1
M6*16 Cabinet
Screws
2
Used for fixing the front
of the cable tray
M6*40 Cabinet
Screws
2
Used for fixing the side
of the cable tray
Spacers*
2
Used for fixing the side
of the cable tray for 800
and 1000mm versions
Cable
Channel*
6
For cables routing, only for
800 and 1000mm versions
Connecting
Rod*
2
Used for cabinets with a
depth of 800mm / 1000mm
Foam Stick
1
Auxiliary tools to ensure
that the bending radians
of the network cables are
consistent
Cable Tie
2
Used for cabinets with a
depth of more than 800mm
Low cost of repeated cable management:
When a line is messy, it does not affect the overall
line direction, convenient and quick recovery
Standardized and cost-effective construction
One-to-one channel routing, non-professional
can achieve standardized wiring
STRUTTURA DEL
Connection
Relationship
Identification
Line Direction
Identification
Layer
Identification
Insert the cable management system into the rack cabinet in the direction indicated by the arrow in
figure 1
Fix to the front rails of the rack in the desired position using M6x16 screws
Secure laterally to the rack using the M6x40 screws that will lock the cable management tray to the
rear rails** (figure 2)
Insert the cable in the desired position and slide it into the guide until it comes out on the other side
of the panel; it is possible to insert the cable both from the front and from the side holes
After cable installation, it is possible to block the cable by inserting the rubber cable clamp on the
front hole of the organizer
For more careful and precise cable management, you can use the supplied foam tube to create an
even bend for all cables. After extracting the cable from the hole, pass it on the surface of the foam
stick and connect it to the equipment to give the correct bending radius, once this step has been
carried out for all the cables, remove the foam stick
One or more organizers can be used within the same rack cabinet depending on the installation
requirements
** For models with depths of 800 and 1000mm it is necessary to install the connection bracket using
the 4 screws supplied; to fix the bracket to the rail, use the spacers and cable ties provided
PACKING LIST
PRODUCT STRUCTURE AND COMPONENT NAMES
Cable Management
Connecting Rod Support Column
Cable Channel
Cabinet Screws
Figure 1 Figure 2
Foam Stick Cable Channel
Support Column
Buckle Position
Cabinet
Screws
* Only for 800 and 1000mm deep version, not included for 600mm version
WWW.TECHLY.COM
MANUALE
D'ISTRUZIONE
SISTEMA DI GESTIONE CAVI
INTRODUZIONE
Questo sistema di gestione cavi per rack è una soluzione intelligente che consente di mantenere in
ordine i cavi e di gestire accuratamente il cablaggio all’interno di un rack 19”.
Ideale per mantenere ordinato e pulito il cablaggio, fondamentale per la verifica e la sostituzione dei
cavi di collegamento.
DESCRIZIONE DELLA FUNZIONE
Identificazione chiara:
Consente l’identificazione del livello, l’identificazione della relazione di connessione, l’identificazione
della direzione della linea
INSTALLAZIONE E ISTRUZIONI DI FUNZIONAMENTO
Nome della parte Immagine Quantità Uso
Organizzatore cavi
1
Viti M6*16
2
Utilizzare per fissare
l’organizzatore ai montanti
frontali dell’armadio
Viti M6*40
2
Utilizzare per fissare
l’organizzatore lateralmente
ai montanti posteriori
dell’armadio
Distanziale staffa
di supporto*
2
Utilizzare per fissare il lato
della staffa passacavi solo
in versioni da 800 e 1000
mm di profondità
Passacavo*
6
Per il passaggio dei cavi,
solo per versioni di 800 e
1000mm di profondità
Staffa di supporto*
2
Fornita in dotazione solo
organizzatori con profondità
800 e 1000mm. Utilizzare
per fissare la staffa
posteriormente ai montanti
Tubo di
gommapiuma
1
Strumento ausiliario per
facilitare
la curvatura del cavo di rete
durante l’assemblaggio
Fascette
2
Utilizzare per armadi con
profondità superiore agli
800mm
Riduzione dei costi di gestione periodica dei
cavi:
Quando una linea è disordinata, l’intervento
tecnico periodico sulla linea non è veloce e
preciso
Costruzione standardizzata e conveniente
Linstradamento del cavo su singola corsia,
consente una gestione professionale del
cablaggio
STRUTTURA DEL
Inserire il sistema di gestione dei cavi all’interno dell’armadio rack nella direzione indicata dalla
freccia nella figura 1
Fissare sui montanti frontali del rack nella posizione desiderata utilizzando le viti M6x16
Fissare lateralmente al rack utilizzando le viti M6x40 che bloccheranno l'organizzatore ai montanti
posteriori ** (figura 2)
Inserire il cavo nella posizione desiderata e farlo scorrere nella guida fino alla sua fuoriuscita sull’altro
lato del pannello; è possibile inserire il cavo sia dai fori frontali che da quelli laterali
Dopo aver effettuato l’installazione del cavo è possibile bloccare il cavo inserendo il fermacavo in
gomma sulla porta frontale dell’organizzatore
Per gestire con maggiore cura a precisione i cavi è possibile utilizzare il tubo di gommapiuma fornito
in dotazione per creare una curvatura omogenea per tutti i cavi. Dopo aver estratto dal foro il cavo,
farlo passare sulla superficie del tubo e collegarlo all’apparecchiatura per dare il raggio di curvatura
corretto, una volta effettuato questo passaggio per tutti i cavi rimuovere il tubo
All’interno dello stesso armadio rack può essere usato uno o più organizzatori a seconda delle
esigenze di installazione
** Per i modelli con profondità 800 e 1000mm è necessario installare la staffa di collegamento usando
le 4 viti in dotazione; per fissare la staffa al montante utilizzare i distanziali e le fascette forniti
LISTA DELLE PARTI
PRODOTTO E SUE PARTI
Organizzatore cavi
Staffa di
Connessione Colonna di supporto
Passacavo
Viti fissaggio
montanti Tubo in
gommapiuma
per curvatura
Passacavi
laterali
Colonna
di supporto
Posizione
passacavi
Viti fissaggio
montanti
* Solo per versione con profondità 800 e 1000mm, parti non incluse per verisone 600mm
Etichetta
identificazione
collegamento
Identificazione
Direzione Linea
Identificazione
Livello
Figura 1 Figura 2


Specyfikacje produktu

Marka: Techly
Kategoria: Nie skategoryzowane
Model: I-CASE TRAY-ORG800

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Techly I-CASE TRAY-ORG800, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą




Instrukcje Nie skategoryzowane Techly

Instrukcje Nie skategoryzowane

Najnowsze instrukcje dla Nie skategoryzowane