Instrukcja obsługi Tascam RC-828
Tascam
Zdalne sterowanie
RC-828
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Tascam RC-828 (7 stron) w kategorii Zdalne sterowanie. Ta instrukcja była pomocna dla 6 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek
Strona 1/7

Section 1 – Starting to use the RC-828
0.98 – 1
1 – Starting to use the RC-828
The TASCAM RC-828 Remote Control Unit
allows you to control up to 4 DTRS1 recorders
(any combination of DA-98, DA-38 or DA-98
units) from one location. The functions which
may be controlled are:
• Transport operations (including jog and
shuttle)
• Track arming
• Auto punch operations
• Chasing control
• Location memories and auto-repeat between
two points
This manual makes reference to the manuals of
the following units: DA-88, DA-38, DA-98 and
SY-88. Please consult these documents as neces-
sary when setting up and using the RC-828.
1.1 Hooking up the RC-828
The RC-828 and DTRS units form a “daisy-
chain”, with the RC-828 being at the head, and the
“tail” unit being terminated with the terminator
supplied with the RC-828.
Use the suppled cable to connect the RC-828 to
the REMOTE IN/SYNC IN of the first DTRS
unit, and a PW-88S cable to connect the SYNC
OUT of the first unit to the REMOTE IN/SYNC
IN of the next unit, and so on, until the terminator
is connected to the SYNC OUT of the last unit in
the chain.
The RC-828’s REC FUNCTION keys 1 through
8 now control the first unit, Keys 9 through 16
control the next unit in the chain, and so on
(regardless of the actual Machine IDs of the
units).
Tighten the screws holding the cable connector to
the RC-828 and to the DTRS unit. This will pre-
vent accidental disconnection of the RC-828 in
the middle of a session.
No power connection is needed for the RC-828.
All power for LEDs, etc. is supplied by the first
DTRS unit.
1.1.1 Machine IDs
Set the machine IDs of the DTRS units so that the
IDs run in a sequence from the unit at the “head”
of the chain, closest to the RC-828 (lowest possi-
ble ID) to the “tail” unit (highest ID). There
should be no gaps in this sequence.
A DA-88 uses a rotary switch to set the ID and
uses 0 as the lowest ID, and a DA-38 or DA-98
uses software to make this setting, and uses 1 as
the lowest ID. Refer to the units’ manuals for full
details of setting the ID.
1 DTRS is a trademark of TEAC Corporation
NOTE
When you connect a number of DTRS units which are of
dierent types, including a DA-98, the DA-98 should be at
the head of the chain immediately following the RC-828.
Other units may then be connected in any order.
If the DTRS units are DA-88s and DA-38s only, they may
be connected in any order.
WARNING
Turn o power to all units when making connections. If you
do not do this, there is a possibility that the RC-828 will
malfunction or even be damaged.
RC-828 DA-38DA-98 DA-88
OUT OUT OUT
IN IN IN
Terminator
Cable supplied
with RC-828
PW-88S PW-88S
WARNING
Use only TASCAM cables to connect the RC-828 to the first
DTRS unit, and to connect the DTRS units to each other. If
the use of cables other than TASCAM cables causes or
results in damage to the units, the warranty is voided.
NOTE
At least one LED is always lit on the RC-828 when it is con-
nected and power is switched on to the DTRS units. If you
do not see any lit LEDs on the RC-828, make sure the
DTRS power is switched on, and check the cable connec-
tions to the RC-828.
Unit
ID as shown
“Real” ID
How the ID is
set (see the
unit’s manual
for details)
Power on or o
when ID is set
DA-98 1 1 Menu system (see
9.2)
ON
DA-88 0 1 Rotary switch on
rear panel (see p23–
24)
OFF
DA-38 1 1 Tape counter menu
system (see 7-2)
ON

Section 2 – Parts of the RC-828
2 – 0.98
1.1.2 Chase mode
In an all-audio setup, the first unit is unlikely to be
chasing external sources. However, subsequent
units in the chain should now chase this master,
using the DTRS (ABS) sync method, when their
CHASE switches are pressed.
However, in some audio setups or an audio-visual
setup, it may be necessary to make the master
DTRS unit slave to incoming timecode:
In this case, you should take care to set the clock
reference of the master DTRS unit appropriately.
2 – Parts of the RC-828
[1] REMOTE connector
Connect one end of the supplied cable to this con-
nector, and the other end to the first DTRS unit, as
described in 1.1, “Hooking up the RC-828”. Make
sure the power to the DTRS unit is turned o
when you make the connection.
[2] REC FUNCTION keys and
indicators
The 32 REC FUNCTION keys allow you to arm
the tracks of up to four DTRS units. Keys 1–8
control the tracks of the first unit in the chain, 9–
16 those of the second, and so on. Pressing keys
which correspond to a non-existent DTRS unit
will have no eect.
Pressing the corresponding keys on the DTRS
units has the same effect as pressing the keys on
the RC-828 unit (i.e. if the track is not armed, it
will now be armed, and vice versa).
The indicators flash when a track is armed for
recording, and light solidly when recording is
being rehearsed or taking place.
[3] CHASE keys and indicators
These keys and indicators allow you to set and
view the chase status of the DTRS units connected
to the RC-828 in the same way as the CHASE
keys and indicators on the units themselves.
[4] ALL INPUT key and indicator
This key performs the same function as the ALL
INPUT key on a DTRS unit, switching the moni-
toring of all tracks on all connected units to the
input source. The indicator lights when this mode
is active.
The INPUT MONITOR keys on the DA-98 also
affect the switching between source and tape.
Using the RC-828 REC FUNCTION keys to
change the status of any tracks while the ALL
INPUT function is on will lose the relationship
between the REC FUNCTION and INPUT
MONITOR status for individual tracks when ALL
INPUT is turned off again. Start recording or re-
set the REC FUNCTION keys to restore this.
If you want to monitor using confidence mode on
a DA-98 unit, make sure that the ALL INPUT key
is off and use the INPUT MONITOR keys on the
DA-98 to turn off input monitoring on all tracks.
[5] AUTO MON key
This key is equivalent to the AUTO MON key on
the DA-98 and performs the same function as this
key on any connected DA-98 units. There is no
key with the same name on the DA-38 or DA-88;
pressing this key is the equivalent of pressing the
INSERT key on a connected DA-38, and pressing
both the AUTO INPUT and INSERT keys on a
DA-88. It is used in punch modes to switch auto-
matically between tape and source when punching
in and out automatically. The indicator lights
when this function is active.
Note that the status of the INPUT MONITOR
keys on a DA-98 will be overridden by the AUTO
MON key. However, when AUTO MON is turned
off again, the original status of these keys will be
restored.
Using the RC-828 REC FUNCTION keys to
change the status of DA-98 tracks while AUTO
MON is on will lose the relationship between the
REC FUNCTION and INPUT MONITOR status
for individual tracks when AUTO MON is turned
off again. Start recording or re-set the REC
FUNCTION keys to restore this.
If you want to monitor using confidence mode on
a DA-98 unit, make sure that the AUTO MON key
NOTE
When you set the machine IDs, you can set the ID of any
machine first, but we recommend doing this in a standard
sequence, working from the head of the chain to the tail.
Reference
DA-98 DA-38 DA-88 SY-88
9.2.3 7-3 p. 24 —
Reference
DA-98 DA-38 DA-88 SY-88
10.7.1 — — 5-1
Reference
DA-98 DA-38 DA-88 SY-88
7.1.1 9.1 (1) p. 9 (18) —

Section 2 – Parts of the RC-828
0.98 – 3
is off and use the INPUT MONITOR keys on
the DA-98 to turn off input monitoring on all
tracks.
[6] JOG/SHTL MON key and indicator
This key allows the selection of different monitor-
ing modes when shuttle mode is selected, either
with the units’ own SHUTTLE controls, or from
the JOG/SHUTTLE key on the RC-828 [15].
This key and indicator duplicate the function of
the SHTL MON key and indicator of the DA-98,
and provide these capabilities for the DA-38 and
DA-98.
Use the flowchart provided with this manual to
check the shuttle monitoring status of DA-38 and
DA-88 units in different modes (the provision of
confidence mode on the DA-98 means that this
model differs from the others), and you should
also consult the manual of the DTRS unit for full
details, if you are unclear about how shuttle moni-
toring works:
[7] RHSL key
This key duplicates the functions of the corre-
sponding key controlling rehearsal operations on
the DTRS units. See the appropriate section of the
DTRS manual if you are unsure of its operation.
[8] AUTO PUNCH key
This key duplicates the functions of the corre-
sponding key controlling auto punch operations
on the DTRS units. See the appropriate section of
the DTRS manual if you are unsure of its
operation.
[9] CLEAR key
This key duplicates the functions of the corre-
sponding key clearing punch points on the DTRS
units. See the appropriate section of the DTRS
manual if you are unsure of its operation.
[10] LOCATE POINTS 1–12
These 12 location keys and indicators are used for
the management of location memories. These
memories are stored and used with reference to
the DTRS unit’s current time reference (ABS or
timecode).
The indicator of a location memory containing a
location point will be lit, and pressing the key
(except in “capture” or erase mode, see [11] and
[12]) will locate to the point stored in that mem-
ory. Pressing a key whose indicator is not lit will
have no effect. The location point stored in the
memory will be briefly shown on the tape counter
of the DTRS units (for the DA-88 and DA-38–for
the DA-98 the location point will be shown briefly
on the LCD display screen).
While location is taking place, the indicator will
flash, and the indicator will light steadily again
when location is complete.
If the AUTO PLAY indicator [13] is lit, the DTRS
unit will start to play back when the location point
is reached, otherwise the transport will stop at the
location point.
[11] CAPTURE key and indicator
Press this key to enter “capture” mode. The green
indicator will flash. While in capture mode, press-
ing a LOCATE POINT key [10] will store the
current tape position to the location memory cor-
responding to the LOCATE POINT key.
If the memory does not contain data (the indicator
is not lit), the new position will be written to the
memory and the indicator will light. If the mem-
ory already contains a location point (the indicator
is lit), this will be overwritten with the new posi-
tion. Press the CAPTURE key again to turn off
the capture mode (the indicator will stop flashing).
[12] ERASE key
To erase a location memory, press and hold down
the ERASE key. While holding it down, press the
LOCATE POINT key [10] of the memory you
want to erase. The indicator of the LOCATE
Reference
DA-98 DA-38 DA-88 SY-88
7.1.3 — — —
Reference
DA-98 DA-38 DA-88 SY-88
6.6 4-3 p. 16 —
NOTE
These location memories are independent of the MEMO 1
and 2 location memories stored in the DTRS units.
NOTE
The location points are stored in memory, backed up by a
battery whose life is a few years. When you turn on the
DTRS unit connected to the RC-828 with location memo-
ries stored in it, the same location indicators will light as
were lit at the time when you last turned o the DTRS unit.
If they do not light, the battery needs replacing, and you
should contact your TASCAM dealer regarding a replace-
ment battery.
Specyfikacje produktu
Marka: | Tascam |
Kategoria: | Zdalne sterowanie |
Model: | RC-828 |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z Tascam RC-828, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje Zdalne sterowanie Tascam

29 Września 2024

16 Września 2024

9 Września 2024

4 Września 2024

31 Sierpnia 2024

20 Sierpnia 2024

18 Sierpnia 2024

16 Sierpnia 2024
Instrukcje Zdalne sterowanie
- Zdalne sterowanie Sony
- Zdalne sterowanie Yamaha
- Zdalne sterowanie Samsung
- Zdalne sterowanie PeakTech
- Zdalne sterowanie AEG
- Zdalne sterowanie LG
- Zdalne sterowanie Motorola
- Zdalne sterowanie Logitech
- Zdalne sterowanie Spektrum
- Zdalne sterowanie BeamZ
- Zdalne sterowanie Pioneer
- Zdalne sterowanie Milwaukee
- Zdalne sterowanie Philips
- Zdalne sterowanie SilverCrest
- Zdalne sterowanie Technics
- Zdalne sterowanie Parkside
- Zdalne sterowanie Hikvision
- Zdalne sterowanie Onkyo
- Zdalne sterowanie Edision
- Zdalne sterowanie Miele
- Zdalne sterowanie Geemarc
- Zdalne sterowanie Bose
- Zdalne sterowanie EZVIZ
- Zdalne sterowanie Panasonic
- Zdalne sterowanie Canon
- Zdalne sterowanie Crestron
- Zdalne sterowanie Nedis
- Zdalne sterowanie Nexa
- Zdalne sterowanie American DJ
- Zdalne sterowanie Medion
- Zdalne sterowanie Toshiba
- Zdalne sterowanie Majestic
- Zdalne sterowanie Jensen
- Zdalne sterowanie Ardes
- Zdalne sterowanie Garmin
- Zdalne sterowanie Iiyama
- Zdalne sterowanie Metra
- Zdalne sterowanie Dual
- Zdalne sterowanie Grundig
- Zdalne sterowanie Hegel
- Zdalne sterowanie Honeywell
- Zdalne sterowanie Chauvet
- Zdalne sterowanie Strong
- Zdalne sterowanie Tripp Lite
- Zdalne sterowanie Steinel
- Zdalne sterowanie Nikon
- Zdalne sterowanie HeiTech
- Zdalne sterowanie Cisco
- Zdalne sterowanie Smart
- Zdalne sterowanie ORNO
- Zdalne sterowanie Kenwood
- Zdalne sterowanie Scosche
- Zdalne sterowanie DJI
- Zdalne sterowanie Alpine
- Zdalne sterowanie Natec
- Zdalne sterowanie Uni-T
- Zdalne sterowanie Chamberlain
- Zdalne sterowanie Bang & Olufsen
- Zdalne sterowanie DSC
- Zdalne sterowanie JVC
- Zdalne sterowanie Trust
- Zdalne sterowanie LogiLink
- Zdalne sterowanie Memphis Audio
- Zdalne sterowanie Grohe
- Zdalne sterowanie Vimar
- Zdalne sterowanie Autel
- Zdalne sterowanie Ansmann
- Zdalne sterowanie Clarion
- Zdalne sterowanie Wacom
- Zdalne sterowanie Thomson
- Zdalne sterowanie Tado
- Zdalne sterowanie Pro-Ject
- Zdalne sterowanie Absima
- Zdalne sterowanie Velleman
- Zdalne sterowanie Fusion
- Zdalne sterowanie Homematic IP
- Zdalne sterowanie Neumann
- Zdalne sterowanie DataVideo
- Zdalne sterowanie One For All
- Zdalne sterowanie Danfoss
- Zdalne sterowanie Intertechno
- Zdalne sterowanie Delta Dore
- Zdalne sterowanie Apple
- Zdalne sterowanie Devolo
- Zdalne sterowanie Marantz
- Zdalne sterowanie Waeco
- Zdalne sterowanie Revox
- Zdalne sterowanie Schaudt
- Zdalne sterowanie Mitsubishi
- Zdalne sterowanie Naim
- Zdalne sterowanie Chief
- Zdalne sterowanie BENNING
- Zdalne sterowanie NAD
- Zdalne sterowanie Continental Edison
- Zdalne sterowanie Delta
- Zdalne sterowanie Harman Kardon
- Zdalne sterowanie Audio-Technica
- Zdalne sterowanie NEC
- Zdalne sterowanie Parrot
- Zdalne sterowanie Antec
- Zdalne sterowanie JL Audio
- Zdalne sterowanie Axis
- Zdalne sterowanie Vision
- Zdalne sterowanie Telefunken
- Zdalne sterowanie Unitron
- Zdalne sterowanie Control4
- Zdalne sterowanie Vogel's
- Zdalne sterowanie Viper
- Zdalne sterowanie Kicker
- Zdalne sterowanie Amazon
- Zdalne sterowanie Abus
- Zdalne sterowanie Olympia
- Zdalne sterowanie Hama
- Zdalne sterowanie Marmitek
- Zdalne sterowanie Omega
- Zdalne sterowanie Optex
- Zdalne sterowanie Reely
- Zdalne sterowanie Schwaiger
- Zdalne sterowanie Watson
- Zdalne sterowanie Loewe
- Zdalne sterowanie Amewi
- Zdalne sterowanie SVS
- Zdalne sterowanie TomTom
- Zdalne sterowanie Arcam
- Zdalne sterowanie Vakoss
- Zdalne sterowanie Yale
- Zdalne sterowanie Technika
- Zdalne sterowanie Silverstone
- Zdalne sterowanie Busch-Jaeger
- Zdalne sterowanie Magnus
- Zdalne sterowanie RCA
- Zdalne sterowanie Genius
- Zdalne sterowanie Futaba
- Zdalne sterowanie Technaxx
- Zdalne sterowanie Hunter
- Zdalne sterowanie Fibaro
- Zdalne sterowanie Gefen
- Zdalne sterowanie Vivanco
- Zdalne sterowanie EQ-3
- Zdalne sterowanie Gaggenau
- Zdalne sterowanie PowerBass
- Zdalne sterowanie Kathrein
- Zdalne sterowanie Rockford Fosgate
- Zdalne sterowanie JUNG
- Zdalne sterowanie TOA
- Zdalne sterowanie Monacor
- Zdalne sterowanie Aputure
- Zdalne sterowanie H-Tronic
- Zdalne sterowanie AudioControl
- Zdalne sterowanie EVE
- Zdalne sterowanie Smartwares
- Zdalne sterowanie Adj
- Zdalne sterowanie Cotech
- Zdalne sterowanie Match
- Zdalne sterowanie Clas Ohlson
- Zdalne sterowanie RADEMACHER
- Zdalne sterowanie KPN
- Zdalne sterowanie Ruwido
- Zdalne sterowanie Profoto
- Zdalne sterowanie AMX
- Zdalne sterowanie Reflecta
- Zdalne sterowanie Ziggo
- Zdalne sterowanie Brennenstuhl
- Zdalne sterowanie Tevion
- Zdalne sterowanie Eminent
- Zdalne sterowanie Targus
- Zdalne sterowanie Sitecom
- Zdalne sterowanie Meliconi
- Zdalne sterowanie Exibel
- Zdalne sterowanie Energy Sistem
- Zdalne sterowanie Doro
- Zdalne sterowanie Hähnel
- Zdalne sterowanie KlikaanKlikuit
- Zdalne sterowanie Ei Electronics
- Zdalne sterowanie Sonos
- Zdalne sterowanie Kensington
- Zdalne sterowanie Steren
- Zdalne sterowanie Bigben Interactive
- Zdalne sterowanie ESYLUX
- Zdalne sterowanie Malmbergs
- Zdalne sterowanie AV:link
- Zdalne sterowanie Vello
- Zdalne sterowanie Audiovox
- Zdalne sterowanie MB Quart
- Zdalne sterowanie FireAngel
- Zdalne sterowanie Asustor
- Zdalne sterowanie Nemef
- Zdalne sterowanie Hema
- Zdalne sterowanie Konig
- Zdalne sterowanie Valueline
- Zdalne sterowanie Sweex
- Zdalne sterowanie Vizio
- Zdalne sterowanie Xit
- Zdalne sterowanie Metronic
- Zdalne sterowanie T'nB
- Zdalne sterowanie Hannspree
- Zdalne sterowanie Xavax
- Zdalne sterowanie Fantini Cosmi
- Zdalne sterowanie Provision
- Zdalne sterowanie Niko
- Zdalne sterowanie Humax
- Zdalne sterowanie Vaddio
- Zdalne sterowanie Zephir
- Zdalne sterowanie Lifetec
- Zdalne sterowanie Apart
- Zdalne sterowanie Electia
- Zdalne sterowanie Projecta
- Zdalne sterowanie Genaray
- Zdalne sterowanie Jolly
- Zdalne sterowanie HQ
- Zdalne sterowanie Msonic
- Zdalne sterowanie Nanlite
- Zdalne sterowanie Verizon
- Zdalne sterowanie Tihao
- Zdalne sterowanie Zapman
- Zdalne sterowanie OEM
- Zdalne sterowanie Emtec
- Zdalne sterowanie Ranex
- Zdalne sterowanie Jasco
- Zdalne sterowanie CME
- Zdalne sterowanie Russound
- Zdalne sterowanie Engel Axil
- Zdalne sterowanie Bazooka
- Zdalne sterowanie Wentronic
- Zdalne sterowanie Walkera
- Zdalne sterowanie EQ3
- Zdalne sterowanie REV
- Zdalne sterowanie Neewer
- Zdalne sterowanie Neets
- Zdalne sterowanie ETiger
- Zdalne sterowanie VDO Dayton
- Zdalne sterowanie Aeon Labs
- Zdalne sterowanie Packard Bell
- Zdalne sterowanie Provision ISR
- Zdalne sterowanie CSL
- Zdalne sterowanie Entone
- Zdalne sterowanie Fortin
- Zdalne sterowanie Samlex
- Zdalne sterowanie Zalman
- Zdalne sterowanie Simplify
- Zdalne sterowanie Interphone
- Zdalne sterowanie SIIG
- Zdalne sterowanie Wet Sounds
- Zdalne sterowanie Televés
- Zdalne sterowanie Swiss Sense
- Zdalne sterowanie Extron
- Zdalne sterowanie ProMaster
- Zdalne sterowanie Ebode
- Zdalne sterowanie RadioShack
- Zdalne sterowanie Exxter
- Zdalne sterowanie Skymaster
- Zdalne sterowanie Hartig Helling
- Zdalne sterowanie Multibox
- Zdalne sterowanie Online
- Zdalne sterowanie Libec
- Zdalne sterowanie Furman
- Zdalne sterowanie AT-T
- Zdalne sterowanie Logic3
- Zdalne sterowanie Medion MD6461
- Zdalne sterowanie TCM
- Zdalne sterowanie Pixel
- Zdalne sterowanie Morel
- Zdalne sterowanie Antelope Audio
- Zdalne sterowanie PDP
- Zdalne sterowanie Ecler
- Zdalne sterowanie Q-Sonic
- Zdalne sterowanie Elite Screens
- Zdalne sterowanie Roswell
- Zdalne sterowanie SpeakerCraft
- Zdalne sterowanie Sunwave
- Zdalne sterowanie Tevion (Medion)
- Zdalne sterowanie Syrp
- Zdalne sterowanie Bravo
- Zdalne sterowanie Maximex
- Zdalne sterowanie Pentatech
- Zdalne sterowanie Glashart Media
- Zdalne sterowanie Bang Olufsen
- Zdalne sterowanie TV Vlaanderen
- Zdalne sterowanie Innr
- Zdalne sterowanie Universal Electronics
- Zdalne sterowanie TELE System
- Zdalne sterowanie Voxx
- Zdalne sterowanie Beoplay
- Zdalne sterowanie Prolectrix
- Zdalne sterowanie Remotec
- Zdalne sterowanie Audiofrog
- Zdalne sterowanie Nanoleaf
- Zdalne sterowanie Tiq
- Zdalne sterowanie Elbe
- Zdalne sterowanie GBS Elettronica
- Zdalne sterowanie Gewiss
- Zdalne sterowanie Insteon
- Zdalne sterowanie Mosconi
- Zdalne sterowanie Lutron
- Zdalne sterowanie CGV
- Zdalne sterowanie Universal Remote Control
- Zdalne sterowanie Aplic
- Zdalne sterowanie Ridem
- Zdalne sterowanie SMK-Link
Najnowsze instrukcje dla Zdalne sterowanie

15 Stycznia 2025

15 Stycznia 2025

15 Stycznia 2025

15 Stycznia 2025

14 Stycznia 2025

14 Stycznia 2025

14 Stycznia 2025

14 Stycznia 2025

12 Stycznia 2025

12 Stycznia 2025