Instrukcja obsługi System Sensor SPRL

System Sensor głośnik SPRL

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla System Sensor SPRL (4 stron) w kategorii głośnik. Ta instrukcja była pomocna dla 2 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/4
1 I56-0001-001
01-12
For use with the following models:
Wall Speakers: SPRL, SPWL
Ceiling Speakers: SPCRL, SPCWL
PRODUCT SPECIFICATIONS
Standard Operating Temperature: 32°F to 120°F (0°C to 49°C)
Humidity Range: 10 to 93% Non-condensing
Nominal Voltage: 25 Volts or 70.7 Volts
Maximum Supervisory Voltage: 50 VDC
Speaker Frequency Range: 400 – 4000 Hz
Power Settings: ¼, ½, 1, 2 Watts
Input terminal wire gauge: 12 to 18 AWG
PRODUCT DIMENSIONS MOUNTING BOX OPTIONS
WALL PRODUCTS Length Width Depth SPEAKERS
Wall Speaker 6.520" (165 mm) 5.00" (127 mm) 0.97" (24.6 mm) 4" x 4" x 2
1
/
8"
or deeper
CEILING PRODUCTS Length Width Depth
Ceiling Speaker 6.8" (173 mm) N/A 1.00" (25.4mm)
NOTICE: This manual shall be left with the owner/user of this equipment.
BEFORE INSTALLING
Please read the System Sensor Voice Evacuation Application Guide, which
provides detailed information on speaker notification devices, wiring and
special applications. Copies of this manual are available from System Sensor.
NFPA 72 and NEMA guidelines should be observed.
Important: The notification appliance used must be tested and maintained
following NFPA 72 requirements.
GENERAL DESCRIPTION
System Sensor series of notification appliances offer a wide range of audible
and visible devices for life safety notification. Our line of speakers is designed
to be used at either 25 or 70.7 volts, and operate at any one of four input
power levels. Our speakers are suitable for dry and damp environments.
These products are electrically backwards compatible with previous genera-
tion of System Sensor speakers. With its low total harmonic distortion, the
System Sensor SPL series offers high fidelity sound output. Wall and ceiling
products may be used interchangeably (wall products may be used on ceiling
and ceiling product may be used on wall).
The speakers, and all power level settings, are listed to ANSI/UL 1480 require-
ments for public mode applications.
FIRE ALARM SYSTEM CONSIDERATIONS
All wiring must be installed in compliance with the National Electrical Code
(NEC) and applicable local codes. System Sensor recommends installing fire
alarm speakers in compliance with NFPA 72, ANSI/UL 1480 and NEC 760.
WIRING AND MOUNTING
All wiring must be installed in compliance with the National Electric Code
and the local codes as well as the authority having jurisdiction. Wiring must
not be of such length or wire size which would cause the notification appli-
ance to operate outside of its published specifications. Improper connections
can prevent the system from alerting occupants in the event of an emergency.
Wire sizes up to 12 AWG (2.5 mm²) may be used with the mounting plate. The
mounting plate ships with the terminals set for 12 AWG wiring.
Make wire connections by stripping about
3
/
8
" of insulation from the end of
the wire. Then slide the bare end of the wire under the appropriate clamping
plate and tighten the clamping plate screw.
See Figure 1 for wiring terminals and strip guide reference.
1. Connect the speaker as shown in Figure 1.
2. There are two rotary switches on the back of the product. The first switch
is used to select either 25 or 70.7 volts input and the second switch is used to
select the input power of ¼, ½, 1 or 2 watts. (See Figure 2.)
FIGURE 1. WIRING DIAGRAM AND WIRING TERMINALS
(-)
(+)
(-)
(+)
Input from
Amplifier
Output to
Next Device or EOL
A0380-00
Wiring Terminals
1. Negative (-). Line in and out
2. Positive (+). Line in and out
3. Positive (+). Line in and out
NOTE: Do not loop electrical wiring
under terminal screws. Wires
connecting the device to the control
panel must be broken at the device
terminal connection in order to
maintain electrical supervision.
FIGURE 2. SPEAKER WATTAGE AND VOLTAGE SETTINGS
A0419-01
INSTALLATION AND MAINTENANCE INSTRUCTIONS
3825 Ohio Avenue, St. Charles, Illinois 60174
800/736-7672, FAX: 630/377-6495
www.systemsensor.com
I56-0001-001
Dual Voltage Speakers
for Fire and ECS/MNS Systems
– Wall and Ceiling Mount
2 I56-0001-001
01-12
MOUNTING
1. Attach mounting plate to junction box. The mounting plate is compatible
with 4" x 4" x 2
1
/
8
" or deeper junction boxes. (See Figures 4 and 5.)
FIGURE 4. WALL SPEAKER
A0500-00
FIGURE 5. CEILING SPEAKER
A0501-00
1. Connect field wiring to terminals, as shown in Figure 1.
2. If the product is not to be installed at this point, use the protective dust
cover to prevent contamination of the wiring terminals on the mounting plate.
3. To attach product to mounting plate, remove the protective dust cover, hook
tabs on the top of the product housing into the grooves on mounting plate.
4. Then, hinge the product into position to engage the pins on the product
with the terminals on the mounting plate. Make sure that the tabs on the back
of the product housing fully engage with the mounting plate.
5. Secure product by tightening the single mounting screw in the front of the
product housing.
CAUTION
The “hold in place” snaps are not intended to secure the product to the back
box. The product must be secured to the back box using the screws provided.
CAUTION
Factory finish should not be altered: Do not paint!
CAUTION
Do not over tighten mounting plate screws; this may cause mounting plate
to flex.
SHORTING SPRING FEATURE
System Sensor notification appliances come with a shorting spring that is pro-
vided between terminals 2 and 3 of the mounting plate to enable system con-
tinuity checks after the system has been wired, but prior to installation of the
final product. (See Figure 3.) This spring will automatically disengage when
the product is installed, to enable supervision of the final system.
FIGURE 3. SHORTING SPRING
Shor
ting
Spring
WIRING TERMINALS
1. Negative (-). Line in and out
2. Positive (+). Line in and out
3. Positive (+). Line in and out
Strip Guide
A0499-01
AVAILABLE POWER SETTINGS
System Sensor offers a wide range of power settings for your life safety needs,
including ¼, ½, 1, and 2W.
Sound levels data per UL 1480 can be found in Table 1. Directional character-
istics can be found in Table 2.
TABLE 1. SOUND LEVELS FOR EACH TRANSFORMER POWER SETTING
Setting UL Reverberant
(dBA @10 ft)
UL Anechoic
(dBA @10 ft)
¼ W 79 79
½ W 82 82
1 W 85 85
2 W 88 88
CAUTION
Signal levels exceeding 130% rated signal voltage can damage the speaker.
Consequently, an incorrect tap connection may cause speaker damage. This
means that if a 25V tap is selected when a 70.7V amplifier is being used,
speaker damage may result. Therefore, be sure to select the proper taps for the
amplifier voltage/input power level combination being used.
TABLE 2 DIRECTIONAL CHARACTERISTICS
Angle (degrees) Decibels
70° -3dB
90° -6dB
3 I56-0001-001
01-12
TAMPER SCREW
For tamper resistance, the standard captive screw may be replaced with the
enclosed Torx screw.
1. To remove the captive screw, back out the screw and apply pressure to the
back until it disengages from the housing. Replace with the supplied Torx
screw. (See Figure 6.)
FIGURE 6. TAMPER SCREW
A0502-00
NOTE: Wall speaker shown in this example.
SURFACE MOUNT BACK BOX MOUNTING
1. The surface mount back box may be secured directly to the wall or ceiling.
A grounding bracket with ground screw capability is provided if needed. For
wall see Figure 7, and for ceiling see Figure 8.
FIGURE 7. WALL SURFACE MOUNT BACK BOX
A0503-00
FIGURE 8. CEILING SURFACE MOUNT BACK BOX
A0504-00
2. The wall mount box must be mounted with the up arrow pointing up. (See
Figure 9.)
FIGURE 9. SMBB UP ARROW
A0481-00
NOTE: Ceiling Surface Mount Back Box, SBBCRL/CWL is a common back box
for ceiling horn strobes, strobes and ceiling speakers and speaker strobes. Use
the top mounting holes for ceiling speaker and speaker strobe products. (See
Figure 10.)
FIGURE 10. CEILING SURFACE MOUNT BACK BOX MOUNTING KEY
HOLE PATTERN
A0505-00
3. Threaded knockout holes are provided for the sides of the box for ¾ inch
conduit adapter. Knockout holes in the back of the box can be used for ¾
inch rear entry.
4. To remove the ¾ inch knockout, we recommend you use a flat head screw-
driver, place the blade of the flat head screwdriver in the inner edge of the
knockout. Strike the screwdriver as you work your way around as shown in
Figure 11.
5. V500 and V700 raceway knockouts are also provided. Use V500 for low
profile applications and V700 for high profile applications.
6. To remove the knockout turn pliers up, as shown in Figure 12.
FIGURE 11 AND 12. KNOCKOUT REMOVAL FOR SURFACE MOUNT BACK
BOX AND WIRE MOLD REMOVAL
¾ inch Wire Mold Removal
A0482-00 A0466-01
NOTE: Use caution not to strike the knockout near the top edge of the wall
version of the surface mount back box.

Specyfikacje produktu

Marka: System Sensor
Kategoria: głośnik
Model: SPRL

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z System Sensor SPRL, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje głośnik System Sensor

System Sensor

System Sensor SPRK Instrukcja

13 Września 2024
System Sensor

System Sensor SPCWK-R Instrukcja

13 Września 2024
System Sensor

System Sensor SPR Instrukcja

10 Września 2024
System Sensor

System Sensor SPWL Instrukcja

9 Września 2024
System Sensor

System Sensor SPRL Instrukcja

6 Września 2024

Instrukcje głośnik

Najnowsze instrukcje dla głośnik

Teufel

Teufel Rockster Air Instrukcja

15 Października 2024
Alpine

Alpine PSS-22WRA Instrukcja

15 Października 2024
Bauhn

Bauhn APPS-0724 Instrukcja

15 Października 2024
Aiwa

Aiwa SP-A100 Instrukcja

15 Października 2024
Harman Kardon

Harman Kardon Citation One Instrukcja

14 Października 2024
Alpine

Alpine 30MC Instrukcja

14 Października 2024
Magnat

Magnat Needle 9000 ALU Instrukcja

14 Października 2024
Pioneer

Pioneer SP-T22A-LR Instrukcja

14 Października 2024
Sharp

Sharp PS-932 Instrukcja

14 Października 2024
Pyle

Pyle PDWR64BTW Instrukcja

13 Października 2024