Instrukcja obsługi Swann SWHOM-DC822P

Swann dzwonek do drzwi SWHOM-DC822P

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Swann SWHOM-DC822P (4 stron) w kategorii dzwonek do drzwi. Ta instrukcja była pomocna dla 9 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Strona 1/4
WIRELESS ALERT
Security Made Smarter
Wireless Door Chime
with Mains Power
EN INSTRUCTION MANUAL
2
PRODUCT OVERVIEW
INSTALLING THE DOORBELL
INSTALLING THE CHIME SPEAKER
1. Insert a small flat-head screwdriver into the small notch at the base of the Doorbell
and lift slightly to remove the rear cover.
2. Install the supplied "CR2032" battery with the "+" symbol facing up. Make sure the
battery is held down securely by the metal prongs.
Note: When replacing the rear cover, make sure the rubber weather seal is in place.
WARNING: The Doorbell unit contains a coin/button cell battery. If the coin/button cell battery is
swallowed, it can cause severe internal burns in just 2 hours and can lead to death. If the battery
compartment does not close securely, stop using the product and keep it away from children.
If you think the battery might have been swallowed or placed inside any part of the body, seek
immediate medical attention.
No wiring is necessary. Just plug the Chime Speaker into an easily accessible power point
and switch the power point on. The Chime Speaker, upon receiving power, automatically
goes into pairing mode for 10 seconds. Within this period, press the Doorbell button
to pair the Doorbell with the Chime Speaker. You will hear the default chime played as
confirmation.
If your Wireless Door Chime system comes with two Chime Speakers, simply repeat the
above procedures to install the additional Chime Speaker.
Note: To pair the Doorbell later, see " .Pairing the Doorbell"
5
6
1LED Indicator
2 (Pairing) Button
3VOL (Volume) Button
4 (Chime Select) Button
5Button
6Nameplate
Chime Speaker Doorbell
1
2
3
4
3
CHANGING THE CHIME
PAIRING THE DOORBELL
ADJUSTING THE CHIME SPEAKER VOLUME
MOUNTING THE DOORBELL
To change the chime that the Chime Speaker plays when someone presses the Doorbell
button, follow the steps below:
1. Press the button repeatedly on the Chime Speaker to cycle through the available
sounds.
2. Stop when you hear a sound that you would like played the next time someone
presses the Doorbell button.
3. Press the Doorbell button to test the chime.
To pair the Doorbell with the Chime Speaker, follow the steps below:
1. Press the button on the Chime Speaker.
2. Within 10 seconds, press the Doorbell button. The Chime Speaker sounds out the
chime that is currently selected as confirmation.
The Chime Speaker can support a maximum of 5 Doorbells at any one time. Additional
Doorbells are available for purchase separately.
The volume of the Chime Speaker is adjustable, if necessary, by pressing the button VOL
until the desired volume level is obtained.
The Doorbell can easily be mounted to the wall with the included double-sided adhesive
tape. The operating distance between the Chime Speaker and the Doorbell is up to
50m/165ft but the range may vary depending on local conditions.
Note: The Doorbell is not suitable for mounting on metal surfaces and UPVC doorframes
as these materials will interfere with the Doorbell's ability to communicate with the Chime
Speaker.


Specyfikacje produktu

Marka: Swann
Kategoria: dzwonek do drzwi
Model: SWHOM-DC822P

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Swann SWHOM-DC822P, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą




Instrukcje dzwonek do drzwi Swann

Instrukcje dzwonek do drzwi

Najnowsze instrukcje dla dzwonek do drzwi

Gira

Gira 2506 20 Instrukcja

15 Października 2024
Panasonic

Panasonic VL-VM902EX Instrukcja

12 Października 2024
Elro

Elro DB260F Instrukcja

10 Października 2024
Eufy

Eufy Video Doorbell C30 Instrukcja

9 Października 2024
Velleman

Velleman HAM9011 Instrukcja

9 Października 2024
CATA

CATA CK 6000 X Instrukcja

8 Października 2024
CATA

CATA THALASSA 600 GWH Instrukcja

8 Października 2024