Instrukcja obsługi Supermicro SuperServer 6018TR-T

Supermicro serwer SuperServer 6018TR-T

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Supermicro SuperServer 6018TR-T (144 stron) w kategorii serwer. Ta instrukcja była pomocna dla 12 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Strona 1/144
SUPERSERVER®
6018TR-T
6018TR-TF
USER’S MANUAL
Revision 1.0
The information in this User’s Manual has been carefully reviewed and is believed to be accurate.
The vendor assumes no responsibility for any inaccuracies that may be contained in this document,
makes no commitment to update or to keep current the information in this manual, or to notify any
person or organization of the updates. Please Note: For the most up-to-date version of this
manual, please see our web site at www.supermicro.com.
Super Micro Computer, Inc. ("Supermicro") reserves the right to make changes to the product
described in this manual at any time and without notice. This product, including software and
documentation, is the property of Supermicro and/or its licensors, and is supplied only under a
license. Any use or reproduction of this product is not allowed, except as expressly permitted by
the terms of said license.
IN NO EVENT WILL SUPERMICRO BE LIABLE FOR DIRECT, INDIRECT, SPECIAL, INCIDENTAL,
SPECULATIVE OR CONSEQUENTIAL DAMAGES ARISING FROM THE USE OR INABILITY TO
USE THIS PRODUCT OR DOCUMENTATION, EVEN IF ADVISED OF THE POSSIBILITY OF
SUCH DAMAGES. IN PARTICULAR, SUPERMICRO SHALL NOT HAVE LIABILITY FOR ANY
HARDWARE, SOFTWARE, OR DATA STORED OR USED WITH THE PRODUCT, INCLUDING THE
COSTS OF REPAIRING, REPLACING, INTEGRATING, INSTALLING OR RECOVERING SUCH
HARDWARE, SOFTWARE, OR DATA.
Any disputes arising between manufacturer and customer shall be governed by the laws of Santa
Clara County in the State of California, USA. The State of California, County of Santa Clara shall
be the exclusive venue for the resolution of any such disputes. Super Micro's total liability for all
claims will not exceed the price paid for the hardware product.
FCC Statement: This equipment has been tested and found to comply with the limits for a Class
A digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the manufacturer’s instruction manual, may cause harmful
interference with radio communications. Operation of this equipment in a residential area is likely
to cause harmful interference, in which case you will be required to correct the interference at your
own expense.
California Best Management Practices Regulations for Perchlorate Materials: This Perchlorate
warning applies only to products containing CR (Manganese Dioxide) Lithium coin cells. “Perchlorate
Material-special handling may apply. See www.dtsc.ca.gov/hazardouswaste/perchlorate
WARNING: Handling of lead solder materials used in this
product may expose you to lead, a chemical known to
the State of California to cause birth defects and other
reproductive harm.
Manual Revision 1.0
Release Date: February 26, 2015
Unless you request and receive written permission from Super Micro Computer, Inc., you may not
copy any part of this document.
Information in this document is subject to change without notice. Other products and companies
referred to herein are trademarks or registered trademarks of their respective companies or mark
holders.
Copyright © 2015 by Super Micro Computer, Inc.
All rights reserved.
Printed in the United States of America
iii
Preface
Preface
About This Manual
This manual is written for professional system integrators and PC technicians. It
provides information for the installation and use of the SuperServer 6018TR-T/TF.
Installation and maintainance should be performed by experienced technicians only.
The SuperServer 6018TR-T/TF is a high-end server based on the SC808BTS-1K03BP
1U rackmount chassis and the dual processor X10DRT-L/LIBF serverboard. All
models have an IPMI LAN port and two serverboard nodes with two hot-swap 3.5"
SATA3 Hard Disk Drives (HDD) each per node.
Each of the various models of the SuperServer 6018TR-T/TF servers and their
associated serverboards for each of their unique options are listed in the table below:
SUPERSERVER 6018TR-T/TF Model Variations
Server
Model
X10DRT
Serverboard
In niBand
FDR Connector
6018TR-T X10DRT-L NO
6018TR-TF X10DRT-LIBF YES
Manual Organization
Chapter 1: Introduction
The rst chapter provides a checklist of the main components included with the
server system and describes the main features of the X10DRT-L/LIBF serverboard
and the SC808BTS-1K03BP chassis.
Chapter 2: Server Installation
This chapter describes the steps necessary to install the SuperServer 6018TR-T/TF
into a rack and check out the server con guration prior to powering up the system.
If your server was ordered without processor and memory components, this chapter
will refer you to the appropriate sections of the manual for their installation.
Chapter 3: System Interface
Refer here for details on the system interface, which includes the functions and
information provided by the control panel on the chassis as well as other LEDs
located throughout the system.
SUPERSERVER 6018TR-T/TF User's Manual
iv
Chapter 4: System Safety
You should thoroughly familiarize yourself with this chapter for a general overview
of safety precautions that should be followed when installing and servicing the
SUPERSERVER 6018TR-T/TF.
Chapter 5: Advanced Serverboard Setup
Chapter 5 provides detailed information on the X10DRT-L/LIBF serverboard,
including the locations and functions of connections, headers and jumpers. Refer
to this chapter when adding or removing processors or main memory and when
recon guring the serverboard.
Chapter 6: Advanced Chassis Setup
Refer to Chapter 6 for detailed information on the SC808BTS-1K03BP server
chassis. You should follow the procedures given in this chapter when installing,
removing or recon guring SATA or peripheral drives and when replacing system
power supply units and cooling fans.
Chapter 7: BIOS
The BIOS chapter includes an introduction to BIOS and provides detailed information
on running the CMOS Setup Utility.
Appendix A: BIOS Error Beep Codes
Appendix B: System Speci cations
v
SUPERSERVER 6018TR-T/TF User's Manual
Notes
vi
Table of Contents
Chapter 1 Introduction
1-1 Overview ......................................................................................................... 1-1
1-2 Serverboard Features ..................................................................................... 1-2
Processors ...................................................................................................... 1-2
Memory ........................................................................................................... 1-2
Serial ATA ....................................................................................................... 1-2
PCI Expansion Slots ....................................................................................... 1-2
Onboard Controllers/Ports .............................................................................. 1-3
Graphics Controller ......................................................................................... 1-3
In niBand ........................................................................................................ 1-3
Other Features ................................................................................................ 1-3
1-3 Server Chassis Features ................................................................................ 1-3
System Power ................................................................................................. 1-3
SATA Subsystem ............................................................................................. 1-4
Front Control Panel ......................................................................................... 1-4
I/O Ports .......................................................................................................... 1-4
Cooling System ............................................................................................... 1-4
Air Shrouds ..................................................................................................... 1-4
Mounting Rails ................................................................................................ 1-5
1-4 Advanced Power Management ....................................................................... 1-5
InteIntelligent Power Node Manager (NM) ................................................. 1-5
Manageability Engine (ME) ............................................................................. 1-5
1-5 Contacting Supermicro .................................................................................... 1-7
1-6 2U Twin2: System Notes ................................................................................. 1-8
Nodes .............................................................................................................. 1-8
System Power ................................................................................................. 1-8
SATA Backplane/Drives ................................................................................... 1-8
Chapter 2 Server Installation
2-1 Overview ......................................................................................................... 2-1
2-2 Unpacking the System .................................................................................... 2-1
2-3 Preparing for Setup ......................................................................................... 2-1
2-4 Warnings and Cautions! .................................................................................. 2-2
Choosing a Setup Location ............................................................................. 2-2
Rack Precautions ............................................................................................ 2-2
Server Precautions .......................................................................................... 2-2
SUPERSERVER 6018TR-T/TF User's Manual
vii
Rack Mounting Considerations ....................................................................... 2-3
Ambient Operating Temperature ................................................................ 2-3
Reduced Air ow ......................................................................................... 2-3
Mechanical Loading ................................................................................... 2-3
Circuit Overloading ..................................................................................... 2-3
Reliable Ground ......................................................................................... 2-4
2-5 Installing the System into a Rack ................................................................... 2-4
Identifying the Sections of the Rack Rails ...................................................... 2-4
Installing the Inner Rail Extension .................................................................. 2-6
Outer Rack Rails ............................................................................................. 2-7
2-6 Checking the Serverboard Setup .................................................................... 2-9
2-7 Checking the Drive Bay Setup ...................................................................... 2-10
Chapter 3 System Interface
3-1 Overview ......................................................................................................... 3-1
3-2 Control Panel Button ...................................................................................... 3-2
3-3 Control Panel LEDs ........................................................................................ 3-2
3-4 Drive Carrier LEDs .......................................................................................... 3-4
Chapter 4 Standardized Warning Statements for AC Systems
4-1 About Standardized Warning Statements ....................................................... 4-1
Warning De nition ........................................................................................... 4-1
Installation Instructions .................................................................................... 4-4
Circuit Breaker ................................................................................................ 4-5
Power Disconnection Warning ........................................................................ 4-6
Equipment Installation ..................................................................................... 4-8
Restricted Area ................................................................................................ 4-9
Battery Handling ............................................................................................ 4-10
Redundant Power Supplies .......................................................................... 4-12
Backplane Voltage ........................................................................................ 4-13
Comply with Local and National Electrical Codes ........................................ 4-14
Product Disposal ........................................................................................... 4-15
Easy Swap Fan Warning .............................................................................. 4-16
Power Cable and AC Adapter ...................................................................... 4-18
Chapter 5 Advanced Motherboard Setup
5-1 Handling the Motherboard .............................................................................. 5-1
Precautions ..................................................................................................... 5-1
Unpacking ....................................................................................................... 5-1
5-2 Connecting Cables .......................................................................................... 5-2
Connecting Data Cables ................................................................................. 5-2
Table of Contents
viii
5-3 Control Panel Connectors and I/O Ports ........................................................ 5-2
Connecting the Control Panel ......................................................................... 5-3
5-4 Processor and Heatsink Installation................................................................ 5-4
Installing a Passive CPU Heatsink ................................................................. 5-8
Removing the Heatsink ................................................................................... 5-9
5-5 Installing Memory .......................................................................................... 5-10
Removing Memory Modules ......................................................................... 5-10
Memory Support .............................................................................................5-11
Maximum Memory ..........................................................................................5-11
Processor & Memory Module Population Con guration ................................5-11
5-6 Adding PCI Expansion Cards ....................................................................... 5-12
5-7 Motherboard Details ...................................................................................... 5-13
5-8 Connector De nitions .................................................................................... 5-16
5-9 Jumper Settings ............................................................................................ 5-23
Explanation of Jumpers ................................................................................ 5-23
5-10 Onboard Indicators ........................................................................................ 5-25
5-11 PCI-Express and Serial ATA Connections .................................................... 5-27
5-12 Installing Drivers ............................................................................................ 5-28
SuperDoctor 5 ............................................................................................... 5-29
5-13 Serverboard Battery ...................................................................................... 5-31
Chapter 6 Advanced Chassis Setup
6-1 Static-Sensitive Devices .................................................................................. 6-1
Precautions ..................................................................................................... 6-1
Unpacking ....................................................................................................... 6-1
6-2 Control Panel .................................................................................................. 6-2
6-3 Chassis Cover ................................................................................................. 6-3
6-4 Air Shrouds ..................................................................................................... 6-4
6-5 Checking the Air ow ....................................................................................... 6-4
6-6 System Fans ................................................................................................... 6-5
6-7 Installing and Removing Hard Drives ............................................................. 6-6
Accessing the Drive Bays ............................................................................... 6-6
6-8 Installing the Motherboard .............................................................................. 6-9
Permanent and Optional Standoffs ................................................................. 6-9
6-9 Expansion Slot Setup .....................................................................................6-11
6-10 Power Supply ................................................................................................ 6-13
Power Supply Replacement .......................................................................... 6-13
SUPERSERVER 6018TR-T/TF User's Manual
Chapter 7 BIOS
7-1 Introduction ...................................................................................................... 7-1
Starting BIOS Setup Utility .............................................................................. 7-1
How To Change the Con guration Data ......................................................... 7-1
Starting the Setup Utility ................................................................................. 7-2
7-2 Main Setup ...................................................................................................... 7-2
7-3 Advanced Settings Menu ................................................................................ 7-4
4-4 Event Logs .................................................................................................... 7-30
4-5 IPMI ............................................................................................................... 7-32
4-6 Security Settings ........................................................................................... 7-34
4-7 Boot Settings ................................................................................................. 7-37
4-8 Save & Exit ................................................................................................... 7-39
Appendix A BIOS Error Beep Codes
Appendix B System Speci cations
ix
Table of Contents
x
Notes
SUPERSERVER 6018TR-T/TF User's Manual
Chapter 1
Introduction
1-1 Overview
The SuperServer 6018TR-T/TF is a high-end server comprised of two main
subsystems: the SC808BTS-1K03BP 2U server chassis and the X10DRT-L/LIBF
dual processor serverboard in four hot-swap nodes. Please refer to our web site for
information on operating systems that have been certi ed for use with the system
(www.supermicro.com).
In addition to the serverboard and chassis, various hardware components have been
included with the SuperServer 6018TR-T/TF server, as listed below:
Heat Sinks
Two (2) 1U passive CPU heat sinks for rear CPU (SNK-P0047PW)
Two (2) 1U passive CPU heat sinks w/narrow ILM (SNK-P0047PS)
Two (2) Mylar air shroud (MCP-310-80803-0B)
Six (6) 40x56-mm 4-pin PWM cooling fans (FAN-0085L4)
Two (2) Round 50-cm 16-to-16-pin ribbon front control cables (CBL-0087)
SATA Backplane
One (1) SATA Backplane for four (4) 3.5" HDD (BPN-SAS-808-O-P)
Four (4) hot-swap 3.5" HDD trays (MCP-220-00075-0B)
One (1) Set of SATA 4-51/47/41/37-cm round S-RA cables (CBL-0201L)
Two (2) 4-pin 20-cm power cables, ST to RA (CBL-0212L)
Two (2) Riser cards (RSC-R1UTP-E16R-O-P)
One (1) Rail set (MCP-290-00042-0V)
Note: For your system to work properly, please follow the links below to download
all necessary drivers/utilities and the user’s manual for your server.
Supermicro product manuals: http://www.supermicro.com/support/manuals/
Product drivers and utilities: ftp://ftp.supermicro.com
Product safety information:
http://super-dev/about/policies/safety_information.cfm
If you have any questions, please contact our support team at:
support@supermicor.com
Chapter 1: Introduction
1-1
1-2
SUPERSERVER 6018TR-T/TF User's Manual
1-2 Serverboard Features
A t t h e h e a r t o f t h e S u p e r S e r v e r 6 0 1 8 T R - T / T F l i e s t h e
X10DRT-L/LIBF, a dual processor serverboard based on the Intel®
C612 chipset and designed to provide maximum performance. Two of these
serverboards can be mounted in the SC808BTS-1K03BP chassis.
The sections below cover the main features of the X10DRT-L/LIBF serverboard
(see Figure 1-1 for a block diagram of the chipset).
Processors
The X10DRT-L/LIBF supports single or dual Inte Xeon® E5-2600 v3 Series
processors (Socket R3-LGA 2011). Please refer to the serverboard description
pages on our web site for a complete listing of supported processors (www.
supermicro.com).
Memory
The X10DRT-L/LIBF has eight (8) DIMM slots supporting up to 256 GB of RDIMM
registered ECC or 512 GB of LRDIMM DDR4 (288-pin) ECC 2133/1866/1600 MHz
speed SDRAM in 512 MB, 1 GB, 2 GB, 4 GB, 8 GB, 16 GB, 32 GB or 64 GB sizes
at 1.2V voltages. See Chapter 5 for details.
Note: Check the Supermicro website (www.supermicro.com) for the latest memory
support information.
Serial ATA
A Serial ATA controller is integrated into the C612 to provide up to twelve SATA3
ports, (six SATA 3 (6 Gb/s) (I-SATA 0-5) and four S-SATA 3 (6 Gb/s) (S-SATA 0-3),
RAID 0, 1, 5 and 10 supported. The SATA drives are hot-swappable units.
Note: The operating system you use must have RAID support to enable the hot-
swap capability and RAID function of the SATA drives.
Note: S-SATA2/S-SATA3: can be used as Supermicro SuperDOM (Disk-on-Module)
with built-in power connectors.
PCI Expansion Slots
The SuperServer 6018TR-T/TF has for each node One (1) PCI-Express 3.0 x16 slot
available for use with a riser card.
1-3
Chapter 1: Introduction
Onboard Controllers/Ports
One Fast UART 16550 port, a single In niBand connector with FDR/QDR support
6018TR-TF only), a VGA (monitor) port, an IPMI dedicated LAN port and two
Ethernet ports, and two USB 2.0 ports (additional one internal USB Type-A
connector is included on the serverboard) are all available on the IO back panel.
Note: For IPMI Con guration Instructions, please refer to the Embedded BMC
Configuration User's Guide available @ http://www.supermicro.com/support/
manuals/.
Graphics Controller
The X10DRT-L/LIBF features an integrated ASpeed 2400 BMC Video Controller.
In niBand
The server include an FDR (fourteen data rate) speed In niBand QSFP connector.
InfiniBand is a scalable serial communications link intended for connecting
processors with high-speed peripherals.
Other Features
Other onboard features that promote system health include onboard voltage
monitors, a chassis intrusion header, auto-switching voltage regulators, chassis and
CPU overheat sensors, virus protection, node manager software and BIOS rescue.
1-3 Server Chassis Features
The following is a general outline of the main features of the SC808 server chassis.
System Power
Each SC808 chassis model includes a high-ef ciency 80-plus Titanium level certi ed
power supply, rated at 1000 Watts plus one redundant backup power supply.
In the unlikely event your power supply fails, replacement is simple and can be
accomplished without tools.
Note: The power supplies are hot-plug.
1-4
SUPERSERVER 6018TR-T/TF User's Manual
SATA Subsystem
The SC808 supports up to four (4) 3.5" hot-swap SATA drives in trays (two for each
node). These drives are hot-swappable units and are connected to a backplane that
provides power and control.
Note: The operating system you use must have RAID support to enable the hot-
swap capability of the drives.
Front Control Panel
SC808BTS-1K03BP chassis includes two front panels on the handles of the chassis
which control each of the systems. Each control panel on the SUPERSERVER
6018TR-T/TF provides you with system monitoring and control for one server
node. LEDs indicate system power, HDD activity, network activity, system overheat
and power supply failure. A main power button and a system reset button are also
included.
I/O Ports
The SC808 is an proprietary form factor chassis designed to be used in a 1U
rackmount con guration. The SC808 chassis provides a low-pro le add-on card
slot, a COM port, a VGA port, two USB 2.0 ports , one IPMI Ethernet port and two
gigabit Ethernet ports per node.
Cooling System
The SC808 chassis accepts six (6) 4-cm system fans powered from either backpane
or the serverboards. If not powered from the backpane, the SC808BTS-1K03BP
model chassis powers three fans from each of the two motherboards, so that when
one of the motherboard drawers is removed, the other motherboards will continue
running its fans.
Note: The fans in this system are NOT redundant, hot-plug.
Air Shrouds
The SC808 chassis includes two plastic air shrouds that direct the air ow where
cooling is needed on each serverboard. Always use the air shroud included with
your chassis on each serverboard.
1-5
Chapter 1: Introduction
Mounting Rails
The SC808 includes a set of rails, and can be placed in a rack for secure storage and
use. To setup your rack, follow the step-by-step instructions included in this manual.
1-4 Advanced Power Management
Intel® Intelligent Power Node Manager (NM)
The Intel® Intelligent Power Node Manager (IPNM) provides your system with
real-time thermal control and power management for maximum energy ef ciency.
Although IPNM Speci cation Version 1.5 is supported by the BMC (Baseboard
Management Controller), your system must also have IPNM-compatible
Manageability Engine (ME) rmware installed to use this feature.
Manageability Engine (ME)
The Manageability Engine, which is an ARC controller embedded in the IOH (I/O
Hub), provides Server Platform Services (SPS) to your system. The services
provided by SPS are different from those proveded by the ME on client platforms.
1-6
SUPERSERVER 6018TR-T/TF User's Manual
Figure 1-1. AMD C612 Chipset:
System Block Diagram
SPI
LAN3
RGMII
Debug Card
FRONT PANEL
CTRL
FAN SPEED
PCI-E X1 G2
USB 2.0
Rev. 1.00
#12 USB2.0
X10DRT-L/LIBQ/LIBF
#1/#2/#4/#5/6/7/8
PCH
6.0 Gb/S
USB 2.0
LPC
USB
#1
#0
RTL8211E-VB-CG
RJ45
BIOS
SPI
SPI
Temp Sensor
W83773G
TPM HEADER
USB 3.0
USB
BIOS
HEADER
SPI
AST2400
BMC
RMII/NCSI
COM1
ConnectorVGA CONN
BMC Boot Flash
DDR3
5 PHASE
145W
P2
P2
P1
VR12.5
P1
#1-3
#1-2
SLOT 1
PCI-E X16 G3
DMI2
PCI-E X16
PCI-E X8 G3
SNB CORE
DDR4
SNB CORE
DDR4
QPI
9.6G
4GB/s
5 PHASE
145W
VR12.5
#3B #1
#2
#2-4
<=1.758W (average)
2.3W (Peak)
TDP: 5W (SERVER)
Idle:0.45W
5V:1.2A
3.3V:0.1A
3.3 STBY:0.2A
1.05 PCH
1.05 ASW
1.5 PCH
PVCCIO 1.0/0.95
3.3STBY:0.5A
PCI-E X4 G3
i350
LAN1
#3
#3A
x2 rear port
Mellanox CX3
IB QDR/FDR
S-SATA
I-SATA
6.0 Gb/S
SPI Switch
SPI
#2
#3
#1
#0
#2
#3
#4
#5
#2 and #3 for SATA DOM SUPPORTED
USB 2.0
USB 3.0
TYPE A
#2-3
#2-2
#2-1
1866/2133
DDR4
#1-4
#1-1
1866/2133
DDR4
SATASATA
#2 #3B
#3A #1
CPU1 CPU2
DMI2 DMI2
Note 1: This is a general block diagram and may not exactly represent the
features on your motherboard. See the Motherboard Features pages for the actual
speci cations of each motherboard.
Note 2: Both CPUs need to be installed for full access to the PCI-E slots, DIMM
slots, and onboard controllers. Refer to the block diagram above to determine which
slots or devices may be affected.
1-7
Chapter 1: Introduction
1-5 Contacting Supermicro
Headquarters
Address: Super Micro Computer, Inc.
980 Rock Ave.
San Jose, CA 95131 U.S.A.
Tel: +1 (408) 503-8000
Fax: +1 (408) 503-8008
Email: marketing@supermicro.com (General Information)
support@supermicro.com (Technical Support)
Website: www.supermicro.com
Europe
Address: Super Micro Computer B.V.
Het Sterrenbeeld 28, 5215 ML
's-Hertogenbosch, The Netherlands
Tel: +31 (0) 73-6400390
Fax: +31 (0) 73-6416525
Email: sales@supermicro.nl (General Information)
support@supermicro.nl (Technical Support)
rma@supermicro.nl (Customer Support)
Website: www.supermicro.nl
Asia-Paci c
Address: Super Micro Computer, Inc.
3F, No. 150, Jian 1st Rd.
Zhonghe Dist., New Taipei City 235
Taiwan (R.O.C)
Tel: +886-(2) 8226-3990
Fax: +886-(2) 8226-3992
Email: support@supermicro.com.tw
Website: www.supermicro.com.tw
1-8
SUPERSERVER 6018TR-T/TF User's Manual
1-6 2U Twin2: System Notes
As a 2U Twin2 con guration, the SuperServer 6018TR-T/TF is a unique server
system. With two system boards incorporated into a single chassis acting as two
separate nodes, there are several points you should keep in mind.
Nodes
Each of the two serverboards act as a separate node in the system. As independant
nodes, each may be powered off and on without affecting the others. In addition,
each node is a hot-swappable unit that may be removed from the rear of the chassis.
The nodes are connected to the server backplane by means of an adapter card.
Note: A guide pin is located between the upper and lower nodes on the inner chassis
wall. This guide pin also acts as a “stopwhen a node is fully installed. If too much
force is used when inserting a node this pin may break off. Take care to slowly slide
a node in until you hear the “click” of the locking tab seating itself.
System Power
Dual 1000 Watt power supplies are used to provide the power for all serverboards.
Each serverboard however, can be shut down independently of the other with the
power button on its own control panel.
SATA Backplane/Drives
As a system, the SuperServer 6018TR-T/TF supports the use of four SATA drives.
A single SATA backplane works to apply system-based control for power and fan
speed functions, yet at the same time logically connects a set of two SATA drives
to each serverboard. Consequently, RAID setup is limited to a two-drive scheme
(RAID cannot be spread across all drives). See the Drive Bay Installation/Removal
section in Chapter 6 for the logical hard drive and node con guration.
Chapter 2: Server Installation
2-1
Chapter 2
Server Installation
2-1 Overview
This chapter provides a quick setup checklist to get your SuperServer 6018TR-T/TF
up and running. Following these steps in the order given should enable you to have
the system operational within a minimum amount of time. This quick setup assumes
that your system has come to you with the processors and memory preinstalled. If
your system is not already fully integrated with a serverboard, processors, system
memory etc., please turn to the chapter or section noted in each step for details on
installing speci c components.
2-2 Unpacking the System
You should inspect the box the SuperServer 6018TR-T/TF was shipped in and note
if it was damaged in any way. If the server itself shows damage you should le a
damage claim with the carrier who delivered it.
Decide on a suitable location for the rack unit that will hold the SuperServer
6018TR-T/TF. It should be situated in a clean, dust-free area that is well ventilated.
Avoid areas where heat, electrical noise and electromagnetic elds are generated.
You will also need it placed near a grounded power outlet. Read the Rack and
Server Precautions in the next section.
2-3 Preparing for Setup
The box the SuperServer 6018TR-T/TF was shipped in should include two sets of
rail assemblies, two rail mounting brackets and the mounting screws you will need
to install the system into the rack. Follow the steps in the order given to complete
the installation process in a minimum amount of time. Please read this section in
its entirety before you begin the installation procedure outlined in the sections that
follow.
2-2
SUPERSERVER 6018TR-T/TF User's Manual
2-4 Warnings and Cautions!
Choosing a Setup Location
Leave enough clearance in front of the rack to enable you to open the front door
completely (~25 inches) and approximately 30 inches of clearance in the back
of the rack to allow for suf cient air ow and ease in servicing.
This product is for installation only in a Restricted Access Location (dedicated
equipment rooms, service closets and the like).
This product is not suitable for use with visual display work place devices
acccording to §2 of the the German Ordinance for Work with Visual Display Units.
Rack Precautions
Ensure that the leveling jacks on the bottom of the rack are fully extended to
the oor with the full weight of the rack resting on them.
In single rack installation, stabilizers should be attached to the rack. In multiple
rack installations, the racks should be coupled together.
Always make sure the rack is stable before extending a component from the
rack.
You should extend only one component at a time - extending two or more
simultaneously may cause the rack to become unstable.
Server Precautions
Review the electrical and general safety precautions in Chapter 4.
Determine the placement of each component in the rack before you install the
rails.
Install the heaviest server components on the bottom of the rack rst, and then
work up.
Use a regulating uninterruptible power supply (UPS) to protect the server from
power surges, voltage spikes and to keep your system operating in case of a
power failure.
Allow any hot plug drives and power supply modules to cool before touching
them.
Always keep the rack's front door and all panels and components on the servers
closed when not servicing to maintain proper cooling.
Chapter 2: Server Installation
2-3
Rack Mounting Considerations
Warning! To prevent bodily injury when mounting or servicing this unit in a
rack, you must take special precautions to ensure that the system remains stable. The
following guidelines are provided to ensure your safety:
This unit should be mounted at the bottom of the rack if it is the only unit in
the rack.
When mounting this unit in a partially lled rack, load the rack from the bottom
to the top with the heaviest component at the bottom of the rack.
If the rack is provided with stabilizing devices, install the stabilizers before
mounting or servicing the unit in the rack.
Ambient Operating Temperature
If installed in a closed or multi-unit rack assembly, the ambient operating
temperature of the rack environment may be greater than the ambient temperature
of the room. Therefore, consideration should be given to installing the equipment
in an environment compatible with the manufacturers maximum rated ambient
temperature (Tmra).
Reduced Air ow
Equipment should be mounted into a rack so that the amount of air ow required
for safe operation is not compromised.
Mechanical Loading
Equipment should be mounted into a rack so that a hazardous condition does not
arise due to uneven mechanical loading.
Circuit Overloading
Consideration should be given to the connection of the equipment to the power
supply circuitry and the effect that any possible overloading of circuits might have
on overcurrent protection and power supply wiring. Appropriate consideration of
equipment nameplate ratings should be used when addressing this concern.
2-4
SUPERSERVER 6018TR-T/TF User's Manual
Reliable Ground
A reliable ground must be maintained at all times. To ensure this, the rack
itself should be grounded. Particular attention should be given to power supply
connections other than the direct connections to the branch circuit (i.e. the use of
power strips, etc.).
2-5 Installing the System into a Rack
This section provides information on installing the SC808 chassis into a rack unit
with the rails provided. There are a variety of rack units on the market, which
may mean the assembly procedure will differ slightly. You should also refer to the
installation instructions that came with the rack unit you are using.
NOTE: This rail will t a rack between 26" and 33.5" deep.
Warning: Do not pick up the server with the front handles. They are designed
to pull the system from a rack only.
Stability Hazard: The rack stabilizing mechanism must be in place, or the
rack must be bolted to the oor before you slide the unit out for servicing. Failure to
stabilize the rack can cause the rack to tip over.
Warning: Slide rail mounted equipment is not to be used as a shelf or a work
space.
Identifying the Sections of the Rack Rails
The chassis package includes two rack rail assemblies in the rack mounting kit.
Each assembly consists of two sections: an inner xed chassis rail that secures
directly to the server chassis and an outer xed rack rail that secures directly to
the rack itself (Figure 2-1).
Chapter 2: Server Installation
2-5
Figure 2-1: Identifying the Sections of the Rack Rails
(Right side rail shown)
Rail Extension
(Inner Rail is preinstalled
to the chassis) Outer Rails
2-6
SUPERSERVER 6018TR-T/TF User's Manual
Figure 2-2: Installing the Inner Rail Extensions
Installing the Inner Rail Extension
The SC808 chassis includes a set of inner rails in two sections: Inner rails and inner
rail extensions. The inner rails are preattached and do not interfere with normal use
of the chassis if you decide not to use a server rack. Attach the inner rail extension
to stabilize the chassis within the rack.
Installing the Inner Rails (Figure 2-2)
1. Place the inner rack extensions on the side of the chassis aligning the hooks
of the chassis with the rail extension holes. Make sure the extension faces
"outward" just like the preattached inner rail.
2. Slide the extension toward the front of the chassis.
3. Secure the chassis with two screws as illustrated.
4. Repeat steps 1-3 for the other inner rail extension.
1
1
1
2
1
3
Chapter 2: Server Installation
2-7
Outer Rack Rails
Outer rails attach to the rack and hold the chassis in place.
Installing the Outer Rails to the Rack (Figure 2-3)
1. Attach the short bracket to the outside of the long bracket. You must align the
pins with the slides. Also, both bracket ends must face the same direction.
2. Adjust both the short and long brackets to the proper distance so that the rail
ts snugly into the rack.
3. Secure the long bracket to the front side of the outer rail with two M5 screws
and the short bracket to the rear side of the outer rail with three M5 screws.
4. Repeat steps 1-4 for the left outer rail.
Figure 2-3. Assembling the Outer Rails
Secure to the
Front of the Rack
Secure to the Rear
of the Rack
Attach Outer Racks
together
2-8
SUPERSERVER 6018TR-T/TF User's Manual
Figure 2-4: Installing the Rack Rails
Installing the Chassis into a Rack (Figure 2-4)
1. Con rm that chassis includes the inner rails (A) and rail extensions (B). Also,
con rm that the outer rails (C) are installed on the rack.
2. Line chassis rails (A and B) with the front of the rack rails (C).
3. Slide the chassis rails into the rack rails, keeping the pressure even on both
sides (you may have to depress the locking tabs when inserting). When the
server has been pushed completely into the rack, you should hear the locking
tabs "click".
4. (Optional) Insert and tightening the thumbscrews that hold the front of the
server to the rack.
Note: The gure above is for illustration purposes only. Always install servers to
the bottom of the rack rst.
1
C
1
B
1
A
Chapter 2: Server Installation
2-9
Figure 2-5. Accessing the Inside of the System
2-6 Checking the Serverboard Setup
After you install the SuperServer 6018TR-T/TF in the rack, you will need to open
the unit to make sure the serverboard is properly installed and all the connections
have been made.
Accessing the inside of the System
Before operating the server for the  rst time, it is important to remove the protective
lm covering the top of the chassis, in order to allow for proper ventilation and
cooling.
Removing the Chassis Cover and Protective Film (Figure 2-5)
1. Disconnect the chassis from any power source and remove all four screws.
2. Gently push down on the chassis cover in the areas indicated in the
illustration.
3. Push the cover toward the rear of the chassis and lift the cover upwards and
off the chassis.
4. Peel off the protective lm covering the top cover and the top of the chassis
5. Check that all ventilation openings on the top cover and the top of the chassis
are clear and unobstructed.
1
3
1
2
1
2
1
3
2-10
SUPERSERVER 6018TR-T/TF User's Manual
Checking the Components and Setup
1. You may have one or two processors already installed into the serverboard.
Each processor needs its own heat sink. See Chapter 5 for instructions on
processor and heat sink installation.
2. Your SuperServer 6018TR-T/TF server system may have come with system
memory already installed. Make sure all DIMMs are fully seated in their slots.
For details on adding system memory, refer to Chapter 5.
3. If desired, you can install add-on cards to the system. See Chapter 5 for
details on installing PCI add-on cards.
4. Make sure all power and data cables are properly connected and not blocking
the chassis air ow. Also make sure that no cables are positioned in front of
the fans. See Chapter 5 for details on cable connections.
2-7 Checking the Drive Bay Setup
Next, you should check to make sure the peripheral drives and the SATA drives
have been properly installed and all connections have been made.
Checking the Drives
1. All drives are accessable from the front of the server. A hard drive can be
installed and removed from the front of the chassis without removing the top
chassis cover.
2. Depending upon your system's con guration, your system may have one or
more drives already installed. If you need to install hard drives, please refer to
Chapter 6.
Checking the Air ow
1. Air ow is provided by six hot-swappable 4-cm chassis cooling fans in two
housings. The system component layout was carefully designed to direct
suf cient cooling air ow to the components that generate the most heat.
2. Note that all power and data cables have been routed in such a way that they
do not block the air ow generated by the fans.
Providing Power
1. Plug the power cord(s) from the power supply unit(s) into a high-quality
power strip that offers protection from electrical noise and power surges. It is
recommended that you use an uninterruptible power supply (UPS).
2. Depress the power on button on the front of the chassis.
Caution: Except for short periods of time, do NOT operate the server without
the cover in place. The chassis cover must be in place to allow proper air ow
and prevent overheating.
Chapter 3: System Interface
3-1
Chapter 3
System Interface
3-1 Overview
There are several LEDs on the control panel and on the drive carriers to keep you
constantly informed of the overall status of the system. SC808 models include
four front panels on the handles of the chassis which control each of the systems.
This chapter explains the meanings of all LED indicators and the appropriate
response you may need to take.
Figure 3-1: Control Panel
SUPERSERVER 6018TR-T/TF User's Manual
3-2
3-2 Control Panel Button
There are two push-buttons located on the front of the chassis. These are (in order
from left to right) a reset button and a power on/off button.
Reset: The reset button is used to reboot the system.
Power: The main power switch is used to apply or remove power from the power
supply to the server system. Turning off system power with this button removes the
main power but keeps standby power supplied to the system. Therefore, you must
unplug system before servicing.
3-3 Control Panel LEDs
The control panel located on the front of the SC808 chassis has ve LEDs. These
LEDs provide you with critical information related to different parts of the system.
This section explains what each LED indicates when illuminated and any corrective
action you may need to take.
Information LED: See the following table for the status shown by this LED.
Information LED
Status Description
Continously on and red An overheat ocondition has occured. (This may be caused by cable congestion.)
Blinking red (1 Hz) Fan failure: check for an inoperative fan.
Blinking red (0.25 Hz) Power failure: check for an inoperative power supply.
Solid blue Local UID has been activated. Use this function to locate the server in a rack
environment.
Blinking blue (300 msec) Remote UID has been activated. Use this function to locate the server from a
remote location.
Chapter 3: System Interface
3-3
NIC2: Indicates network activity on GLAN2 when ashing
NIC1: Indicates network activity on GLAN1 when ashing
HDD: Indicates IDE channel activity. SAS/SATA drive, and/or DVD-ROM drive
activity when ashing.
Power: Indicates power is being supplied to the system's power supply units. This
LED should normally be illuminated when the system is operating.
SUPERSERVER 6018TR-T/TF User's Manual
3-4
3-4 Drive Carrier LEDs
The chassis includes externally accessible SAS/SATA drives. Each drive carrier
displays two status LEDs on the front of the carrier.
LED Color State Status
Activity LED Green Solid On SAS drive installed
Green Blinking I/O activity
Status LED Red Solid On Failed drive for SAS/SATA with RSTe
support
Red Blinking at 1 Hz Rebuild drive for SAS/SATA with RSTe
support
Red Blinking with two blinks
and one stop at 1 Hz
Hot spare for SAS/SATA with RSTe
support
Red On for  ve seconds,
then off
Power on for SAS/SATA with RSTe
support
Red Blinking at 4 Hz Identify drive for SAS/SATA with RSTe
support
4-1
Chapter 4: Warning Statements for AC Systems
Chapter 4
Standardized Warning Statements for AC Systems
4-1 About Standardized Warning Statements
The following statements are industry standard warnings, provided to warn the user
of situations which have the potential for bodily injury. Should you have questions
or experience difficulty, contact Supermicro's Technical Support department
for assistance. Only certi ed technicians should attempt to install or con gure
components.
Read this appendix in its entirety before installing or con guring components in the
Supermicro chassis.
These warnings may also be found on our web site at http://www.supermicro.com/
about/policies/safety_information.cfm.
Warning De nition
Warning!
This warning symbol means danger. You are in a situation that could cause bodily
injury. Before you work on any equipment, be aware of the hazards involved with
electrical circuitry and be familiar with standard practices for preventing accidents.
警告の定義
の警告サ険を意味
人身事故につながる可能性がいずれの機器前に
電気回路に危険性に注意準的な事故防止策精通い。
此警告符号代表危险。
您正处于可能受到严重伤害的工作环境中。在您使用设备开始工作之前,必须充分
意识到触电的危险,并熟练掌握防止事故发生的标准工作程序。请根据每项警告结
尾的声明号码找到此设备的安全性警告说明的翻译文本。
此警告符號代表危險。
您正處於可能身體可能會受損傷的工作環境中。在您使用任何設備之前,請注意觸
電的危險,並且要熟悉預防事故發生的標準工作程序。請依照每一注意事項後的號
碼找到相關的翻譯說明內容
4-2
SUPERSERVER 6018TR-T/TF User's Manual
Warnung
WICHTIGE SICHERHEITSHINWEISE
Dieses Warnsymbol bedeutet Gefahr. Sie be nden sich in einer Situation, die zu
Verletzungen führen kann. Machen Sie sich vor der Arbeit mit Geräten mit den
Gefahren elektrischer Schaltungen und den üblichen Verfahren zur Vorbeugung
vor Unfällen vertraut. Suchen Sie mit der am Ende jeder Warnung angegebenen
Anweisungsnummer nach der jeweiligen Übersetzung in den übersetzten
Sicherheitshinweisen, die zusammen mit diesem Gerät ausgeliefert wurden.
BEWAHREN SIE DIESE HINWEISE GUT AUF.
INSTRUCCIONES IMPORTANTES DE SEGURIDAD
Este símbolo de aviso indica peligro. Existe riesgo para su integridad física. Antes
de manipular cualquier equipo, considere los riesgos de la corriente eléctrica y
familiarícese con los procedimientos estándar de prevención de accidentes. Al
nal de cada advertencia encontrará el número que le ayudará a encontrar el texto
traducido en el apartado de traducciones que acompaña a este dispositivo.
GUARDE ESTAS INSTRUCCIONES.
IMPORTANTES INFORMATIONS DE SÉCURI
Ce symbole d'avertissement indique un danger. Vous vous trouvez dans une
situation pouvant entraîner des blessures ou des dommages corporels. Avant
de travailler sur un équipement, soyez conscient des dangers liés aux circuits
électriques et familiarisez-vous avec les procédures couramment utilisées pour
éviter les accidents. Pour prendre connaissance des traductions des avertissements
gurant dans les consignes de sécurité traduites qui accompagnent cet appareil,
référez-vous au numéro de l'instruction situé à la n de chaque avertissement.
CONSERVEZ CES INFORMATIONS.
ןונקת
ןונקת
ןונקת
ןונקתןונקת
תורהצה
תורהצה
תורהצה
תורהצהתורהצה
א
א
א
אא
הרהז
הרהז
הרהז
הרהזהרהז
ןה תואבה תורהצהא , ינפמ שמתשמה תא ריהזהל תנמ לע היישעתה ינקת יפ לע תורהז הלבח
ה וא תולאש שיו הדימב .תירשפא תיזיפי , יהשלכ היעבב תולקתרוציל שי הכימת תקלחמ םע רשק
רידגהל וא ןיקתהל םיאשר דבלב םיכמסומ םיאנכט .ורקימרפוס לש תינכ תאה .םיביכר
אורקל שי . ורקימרפוס יזראמב םיביכרה תרדגה וא תנקתה ינפל ואולמב חפסנה תא
4-3
Warning Statements for AC Systems
  
!
     .    
   .       
         
  .
          

BELANGRIJKE VEILIGHEIDSINSTRUCTIES
Dit waarschuwings symbool betekent gevaar. U verkeert in een situatie die
lichamelijk letsel kan veroorzaken. Voordat u aan enige apparatuur gaat werken,
dient u zich bewust te zijn van de bij een elektrische installatie betrokken risico's
en dient u op de hoogte te zijn van de standaard procedures om ongelukken te
voorkomen. Gebruik de nummers aan het eind van elke waarschuwing om deze te
herleiden naar de desbetreffende locatie.
BEWAAR DEZE INSTRUCTIES
. ﻲﻓ ﻚﻧﺍ ﻥﺃ ﻦﻜﻤﻳ ﺔﻟﺎﺣ ﻲﻓ ﺐﺒﺴﺘﺗ ﺔﺑﺎﺻﺍ ﺔﻳﺪﺴﺟ ﺰﻣﺮﻟﺍ ﺍﺬﻫ ﻲﻨﻌﻳ ﺮﻄﺧ !ﺮﻳﺬﺤ
ﻥﺃ ﻞﺒ ﻱﺃ ﻰﻠﻋ ﻞﻤﻌﺗ ﺍﺪﻌﻣ،ﻢﻠﻋ ﻰﻠﻋ ﻦﻋ ﺔﻤﺟﺎﻨﻟﺍ ﺮﻁﺎﺨﻤﻟﺎﺑ ﺮﺋﺍﻭﺪﻟ
ﺔﻴﺋﺎﺑﺮﻬﻜﻟﺍ
ﻛﻭﺔﻳﺍﺭﺩ ﻰﻠﻋ ﺭﺎﻤﻤﻟﺎﺑﺕﺎ ﺔﻴﺋﺎﻗﻮﻟﺍ ﻊﻨﻤﻉﻮﻗﻭ ﻱﺃﺙﺩﺍﻮﺣ
ﻢﻗﺭ ﺪﺨﺘﺳ ﺎﻴﺒﻟﺍ ﺹﻮﺼﻨﻤﻟﺍ ﺔﻳﺎﻬﻧ ﻲﻓ ﺮﻳﺬﺤﺗ ﻞﻛ ﺭﻮﺜﻌﻠﻟ ﺎﻬﺘﻤﺟﺮﺗ
4-4
SUPERSERVER 6018TR-T/TF User's Manual
Installation Instructions
Warning!
Read the installation instructions before connecting the system to the power source.
設置手順書
ステ電源に接続す前に設置手順書をお読み下い。
警告
将此系统连接电源,请先阅读安装说明。
警告
將系統與電源連接前,請先閱讀安裝說明。
Warnung
Vor dem Anschließen des Systems an die Stromquelle die Installationsanweisungen
lesen.
¡Advertencia!
Lea las instrucciones de instalación antes de conectar el sistema a la red de
alimentación.
Attention
Avant de brancher le système sur la source d'alimentation, consulter les directives
d'installation.
ﻟﺍ ﺕﺍﺩﺎﺷﺭﺇ ﺮﻗﺍﺐﻴﻛﺮﺘ ﻞﻴﺻﻮﺗ ﻞﺒ ﻰﻟﺇ ﻡﺎﻈﻨﻟﺍ ﺔﻗﺎﻄﻠﻟ ﺭﺪﺼﻣ
אורקל שי רוקמל תכרעמה רוביח ינפל הנקתה תוארוה תאחתמ.
      .
Waarschuwing
Raadpleeg de installatie-instructies voordat u het systeem op de voedingsbron
aansluit.
4-5
Chapter 4: Warning Statements for AC Systems
Circuit Breaker
Warning!
This product relies on the building's installation for short-circuit (overcurrent)
protection. Ensure that the protective device is rated not greater than: 250 V, 20 A.
ーキレー
の製品は、短絡(過電流)保護装置がる建物での設を前
保護装置の定格が250V20Aを超ないを確認下い。
警告
此产品的短路(过载电流)保护由建筑物的供电系统提供,确保短路保护设备的额定电
流不大于250V,20A
警告
此產品的短路(過載電流)保護由建築物的供電系統提供,確保短路保護設備的額定電
流不大於250V,20A
Warnung
Dieses Produkt ist darauf angewiesen, dass im Gebäude ein Kurzschluss-
bzw. Überstromschutz installiert ist. Stellen Sie sicher, dass der Nennwert der
Schutzvorrichtung nicht mehr als: 250 V, 20 A beträgt.
¡Advertencia!
Este equipo utiliza el sistema de protección contra cortocircuitos (o sobrecorrientes)
del edi cio. Asegúrese de que el dispositivo de protección no sea superior a: 250
V, 20 A.
Attention
Pour ce qui est de la protection contre les courts-circuits (surtension), ce produit
dépend de l'installation électrique du local. Véri ez que le courant nominal du
dispositif de protection n'est pas supérieur à :250 V, 20 A.
לע ךמתסמ הז רצומנגהה תעינמל םינבמב תנקתומה . יכ אדוול שי ילמשח רצק
רצקה ינפמ ןגמה רישכמה ילמשחהמ רתוי אל אוה-250 V, 20 A
4-6
SUPERSERVER 6018TR-T/TF User's Manual
Power Disconnection Warning
Warning!
The system must be disconnected from all sources of power and the power cord
removed from the power supply module(s) before accessing the chassis interior to
install or remove system components.
電源切断の警
ーネの取付けは取めにシー内部に
ムの電源はすべてされ、は電源モルか
外す必要があ
警告
在你打开机箱并安装或移除内部器件前,必须将系统完全断电,并移除电源线。
警告
在您打開機殼安裝或移除內部元件前,必須將系統完全斷電,並移除電源線。
!
   ()     
.    250V(), 20A() 
  .
Waarschuwing
Dit product is afhankelijk van de kortsluitbeveiliging (overspanning) van uw electrische
installatie. Controleer of het beveiligde aparaat niet groter gedimensioneerd is dan
220V, 20A.
ﺞﺘﻨﻤﻟﺍ ﺍﺬﻫ ﻰﻠﻋ ﺪﻤﺘﻌ ﺕﺍﺪﻌﻣ ﺔﻳﺎﻤﺤﻟﺍ ﺓﺮﻴﺼﻘﻟﺍﺮﺋﺍﻭﺪﻟﺍ ﻦﻣ ﺎﻬﺘﻴﺒﺜﺗ ﻢﺗ ﻲﺘﻟﺍ ﻲﻓ ﻰﻨﺒﻤﻟﺍ
20A, 250V : ﻦﻣ ﺪﻛﺄ ﻥﺃ ﻢﻴﻴﻘﺗ ﺯﺎﻬﺠﻟﺍ ﻟﺍﻲﺋﺎﻗﻮ ﺲﻴﻟ ﺮﺜ
4-7
Chapter 4: Warning Statements for AC Systems
Warnung
Das System muss von allen Quellen der Energie und vom Netzanschlusskabel
getrennt sein, das von den Spg.Versorgungsteilmodulen entfernt wird, bevor es
auf den Chassisinnenraum zurückgreift, um Systemsbestandteile anzubringen oder
zu entfernen.
¡Advertencia!
El sistema debe ser disconnected de todas las fuentes de energía y del cable
eléctrico quitado de los dulos de fuente de alimentación antes de tener acceso
el interior del chasis para instalar o para quitar componentes de sistema.
Attention
Le système doit être débranché de toutes les sources de puissance ainsi que de
son cordon d'alimentation secteur avant d'acder à l'intérieur du chassis pour
installer ou enlever des composants de systéme.
ילמשח
ילמשח
ילמשח
ילמשחילמשח קותינ
קותינ
קותינ
קותינקותינ ינפמ
ינפמ
ינפמ
ינפמינפמ הרהזא
הרהזא
הרהזא
הרהזאהרהזא
!
!
!
!!הרהזא
הרהזא
הרהזא
הרהזאהרהזא
למשחה תורוקמ לכמ תכרעמה תא קתנל שי ריסהל שיו קפסהמ ילמשחה לבכ תא
נקתה ךרוצל זראמה לש ימינפה קלחל השיג ינפלת רסה ואת .םיביכר
ﻞﺼﻓ ﺐﺠﻳ ﻡﺎﻈﻨﻟ ﻊﻴﻤﺟ ﻦﻣﺭﺩﺎﺼﻣ ﺔﻗﺎﻄﻟﺍ ﺔﻟﺍﺯﺇﻭ ءﺎﺑﺮﻬﻜﻟﺍ ﻚﻠ ﻦﻣ ﺓﺪﺣﻭ ﺩﺍﺪﻣ
ﺔﻗﺎﻄﻟﺍ ﻞﺒﻗ
ﻰﻟﺇ ﻝﻮﺻﻮﻟﺍ ﺔﻴﻠﺧﺍﺪﻟ ﻖﻁﺎﻨﻤﻟﺍ ﻞﻜﻴﻬﻠ ﺔﻟﺍﺯﺇ ﻭﺃ ﺖﻴﺒﺜﺘ ﺕﺎﻧﻮﻜﻣ ﺯﺎﻬﺠﻟﺍ
!
        
       
.
Waarschuwing
Voordat u toegang neemt tot het binnenwerk van de behuizing voor het installeren
of verwijderen van systeem onderdelen, dient u alle spanningsbronnen en alle
stroomkabels aangesloten op de voeding(en) van de behuizing te verwijderen
4-8
SUPERSERVER 6018TR-T/TF User's Manual
Equipment Installation
Warning!
Only trained and quali ed personnel should be allowed to install, replace, or service
this equipment.
機器の設置
レーグを受けれた人だけがの装置の設置たはサービスを許
警告
只有经过培训且具有资格的人员才能进行此设备的安装、更换和维修。
警告
只有經過受訓且具資格人員才可安裝、更換與維修此設備。
Warnung
Das Installieren, Ersetzen oder Bedienen dieser Ausrüstung sollte nur geschultem,
quali ziertem Personal gestattet werden.
¡Advertencia!
Solamente el personal cali cado debe instalar, reemplazar o utilizar este equipo.
Attention
Il est vivement recomman de confier l'installation, le remplacement et la
maintenance de ces équipements à des personnels quali és et expérimentés.
!הרהזא
שר דבלב ךמסומ תווצתא ףילחהל ,ןיקתהל יא . דויצה רובע תוריש תתל וא דויצה
ﻦﻴﺑﺭﺪﻤﻟﺍﻭ ﺐﻴﻛﺮﺘﻝﺍﺪﺒﺘﺳﺍ ﻭﺃ ﺔﻣﺪﺧ ﺎﻬﺠﻟﺍ ﺍﺬﻫ ﺢﻤﺴﻳ ﺐﺠﻳ ﻂﻘﻓ ﻦﻴﻠﻫﺆﻤﻟﺍ ﻦﻴﻔﻅﻮﻤﻠﻟ
!
     ,    
.
4-9
Chapter 4: Warning Statements for AC Systems
Restricted Area
Warning!
This unit is intended for installation in restricted access areas. A restricted access
area can be accessed only through the use of a special tool, lock and key, or other
means of security. (This warning does not apply to workstations).
ス制限区域
のユニは、ス制限区域設置想定
ス制限区域は別なツール前、の他のセの手段を用い
み出入が可能で
警告
安装使
钥匙或其它安全手段进出的场所。
警告
限安
或其他安全方式才能進入的區域。
Warnung
Diese Einheit ist zur Installation in Bereichen mit beschränktem Zutritt vorgesehen.
Der Zutritt zu derartigen Bereichen ist nur mit einem Spezialwerkzeug, Schloss und
Schlüssel oder einer sonstigen Sicherheitsvorkehrung möglich.
¡Advertencia!
Esta unidad ha sido diseñada para instalación en áreas de acceso restringido.
Sólo puede obtenerse acceso a una de estas áreas mediante la utilización de una
herramienta especial, cerradura con llave u otro medio de seguridad.
Attention
Cet appareil doit être installée dans des zones d'accès réservés. L'accès à une
zone d'accès réservé n'est possible qu'en utilisant un outil spécial, un mécanisme
de verrouillage et une clé, ou tout autre moyen de sécurité.
Waarschuwing
Deze apparatuur mag alleen worden geïnstalleerd, vervangen of hersteld door
geschoold en gekwali ceerd personeel.
4-10
SUPERSERVER 6018TR-T/TF User's Manual
Battery Handling
Warning!
There is the danger of explosion if the battery is replaced incorrectly. Replace the
battery only with the same or equivalent type recommended by the manufacturer.
Dispose of used batteries according to the manufacturer's instructions
電池の取扱い
電池交換が正行われなか場合、裂の危険性が換する電メー
が推奨すたは同等のを使使用済電は製造元の指示に
い。
警告
电池更换不当会有爆炸危险。请只使用同类电池或制造商推荐的功能相当的电池更
换原有电池。请按制造商的说明处理废旧电池。
警告
電池更換不當會有爆炸危險。請使用製造商建議之相同或功能相當的電池更換原有
電池。請按照製造商的說明指示處理廢棄舊電池。
תלבגומ
תלבגומ
תלבגומ
תלבגומתלבגומ השיג
השיג
השיג
השיגהשיג םע
םע
םע
םעםע רו
רו
רו
רורו
!
!
!
!!הרהזא
הרהזא
הרהזא
הרהזאהרהזא
. תרזעב תנתינ השיגה השיג תלבגה םהב שיש םירוזאב הדיחיה תא ןיקתה
.('דכו לוענמ ,חתפמ) דבלב החטבא ילכ
. ﺺﻴﺼﺨﺗ ﺓﺪﺣﻮﻟﺍ ﻩﺬﻫ ﻲﻓ ﺎﻬﺒﻴﻛﺮﺘﻟ ﻖﻁﺎﻨﻣ ﺓﺭﻮﻈﺤﻣ ﻢﺗ
ﺻﻮﻟﺍ ﻦﻜﻤﻳﻰﻟﺇ ﻝﻮ ﺔﻘﻄﻨﻣ ﺓﺭﻮﻈﺤﻣ ﻂﻘﻓ ﻡﺍﺪﺨﺘﺳﺍ ﻝﻼﺧ ﻦﻣ ،ﺔﺻﺎﺧ ﺓﺍﺩﺃ
ﻭﺃ ﻱﺃ ﻼﻟ ﻯﺮﺧﺃ ﺔﻠﻴﺳﻭﻥﺎﻣﻷ ﺡﺎﺘﻔﻣﻭ ﻞﻔﻗ
!
     . ,  
,          .
Waarschuwing
Dit apparaat is bedoeld voor installatie in gebieden met een beperkte toegang.
Toegang tot dergelijke gebieden kunnen alleen verkregen worden door gebruik te
maken van speciaal gereedschap, slot en sleutel of andere veiligheidsmaatregelen.
4-11
Chapter 4: Warning Statements for AC Systems
Warnung
Bei Einsetzen einer falschen Batterie besteht Explosionsgefahr. Ersetzen Sie die
Batterie nur durch den gleichen oder vom Hersteller empfohlenen Batterietyp.
Entsorgen Sie die benutzten Batterien nach den Anweisungen des Herstellers.
Attention
Danger d'explosion si la pile n'est pas remplacée correctement. Ne la remplacer
que par une pile de type semblable ou équivalent, recommandée par le fabricant.
Jeter les piles usagées conformément aux instructions du fabricant.
¡Advertencia!
Existe peligro de explosión si la batería se reemplaza de manera incorrecta.
Reemplazar la batería exclusivamente con el mismo tipo o el equivalente
recomendado por el fabricante. Desechar las baterías gastadas según las
instrucciones del fabricante.
!
!
!
!!הרהזא
הרהזא
הרהזא
הרהזאהרהזא
תנכס תמייקץוציפ . הניקת אל ךרדב הפלחוהו הדימב הללוסה לש ףילחהל שי
גוסב הללוסה תא מ םאותה תרבחלמומ ןרציתצ.
תוללוסה קוליס תושמושמה עצבל שי .ןרציה תוארוה יפל
ﺮﻄﺧ ﻙﺎﻨ ﻦﻣ ﻝﺍﺪﺒﺘﺳ ﺔﻟﺎﺣ ﻲﻓ ﺭﺎﺠﻔﻧﺍ ﺔﻳﺭﺎﻄﺒﻟﺍ ﺔﺤﻴﺤﺻ ﺮﻴ ﺔﻘﻳﺮﻄﺑ ﻚﻴﻠﻌﻓ ﺔﻳﺭﺎﻄﺒﻟﺍ ﺍﺪﺒﺘﺳﺍ
ﻂﻘﻓ ﻉﻮﻨﻟﺍ ﺲﻔﻨ ﺎﻬﻟﺩﺎﻌﻳ ﺎﻣ ﻭﺃ ﺎﻤﺖﺻﻭﺃ ﻌﻨﺼﻤﻟﺍ ﺔﻛﺮﺸﻟﺍ ﻪﺑ
ﺕﺎﻳﺭﺎﻄﺒﻟﺍ ﻦﻣ ﺺﻠﺨﺗ ﺎﻘﻓﻭ ﺔﻠﻤﻌﺘﺴﻤﻟﺍﺔﻌﻧﺎﺼﻟﺍ ﺔﻛﺮﺸﻟﺍ ﺕﺎﻤﻴﻠﻌﺘ
!
  . 
       .
      .
Waarschuwing
Er is ontplof ngsgevaar indien de batterij verkeerd vervangen wordt. Vervang de
batterij slechts met hetzelfde of een equivalent type die door de fabrikant aanbevolen
wordt. Gebruikte batterijen dienen overeenkomstig fabrieksvoorschriften afgevoerd
te worden.
4-12
SUPERSERVER 6018TR-T/TF User's Manual
Redundant Power Supplies
Warning!
This unit might have more than one power supply connection. All connections must
be removed to de-energize the unit.
冗長電源装置
のユニ複数の電源装置が接続れて合が
の電源をためすべ接続外させん
警告
此部件连接的电源可能不止一个,必须将所有电源断开才能停止给该部件供电。
警告
此裝置連接的電源可能不只一個,必須切斷所有電源才能停止對該裝置的供電。
Warnung
Dieses Gerät kann mehr als eine Stromzufuhr haben. Um sicherzustellen, dass
der Einheit kein trom zugeführt wird, müssen alle Verbindungen entfernt werden.
¡Advertencia!
Puede que esta unidad tenga más de una conexión para fuentes de alimentación.
Para cortar por completo el suministro de energía, deben desconectarse todas las
conexiones.
Attention
Cette unité peut avoir plus d'une connexion d'alimentation. Pour supprimer toute
tension et tout courant électrique de l'unité, toutes les connexions d'alimentation
doivent être débranchées.
דחא
דחא
דחא
דחאדחא קפסמ
קפסמ
קפסמ
קפסמקפסמ רתוי
רתוי
רתוי
רתוירתוי םייק
םייק
םייק
םייקםייק םא
םא
םא
םאםא
!
!
!
!!הרהזא
הרהזא
הרהזא
הרהזאהרהזא
. קפס לש דחא רוביחמ רתוי שי הדחיל תא ריסהל שי ןקורל תנמ לע םירוביחה לכ חיה תאי.הד
4-13
Chapter 4: Warning Statements for AC Systems
Backplane Voltage
Warning!
Hazardous voltage or energy is present on the backplane when the system is
operating. Use caution when servicing.
レーの電圧
ムの稼働中は危険な電圧たは電力がレー上にかか
修理す際に注意
警告
当系统正在进行时,背板上有很危险的电压或能量,进行维修时务必小心。
警告
當系統正在進行時,背板上有危險的電壓或能量,進行維修時務必小心。
Warnung
Wenn das System in Betrieb ist, treten auf der Rückwandplatine gefährliche
Spannungen oder Energien auf. Vorsicht bei der Wartung.
¡Advertencia!
Cuando el sistema está en funcionamiento, el voltaje del plano trasero es peligroso.
Tenga cuidado cuando lo revise.
.ﺪﻗ ﺍﺬﻬﻟ ﻥﻮﻜﻳ ﻟﺍﺯﺎﻬﺠ ﺕﻻﺎﺼﺗﺍ ﺓﺪﻋ ﺕﺍﺪﺣﻮﺑ ﺔﻗﺎﻄﻟﺍ ﺩﺍﺪﻣﺍ
ﺔﻟﺍﺯﺇ ﺐﺠﻳ ﺕﻻﺎﺼﺗﻻﺍ ﺔﻓﺎﻛ ﻝﺰﻌﻟ ﻟﺍﺓﺪﺣﻮ ﻦﻋ ءﺎﺑﻬﻜﻟﺍ
경고!
이 장치에는 한 개 이상의 전원 공급 자가 연결되어 있을 수 있습니다. 이 장치에
전원을 차단하기 위해서모든 연결 단자를 제거해야만 합니다.
Waarschuwing
Deze eenheid kan meer dan één stroomtoevoeraansluiting bevatten. Alle
aansluitingen dienen verwijderd te worden om het apparaat stroomloos te maken.
4-14
SUPERSERVER 6018TR-T/TF User's Manual
Comply with Local and National Electrical Codes
Warning!
Installation of the equipment must comply with local and national electrical codes.
地方おび国の電気規格に準拠
機器の取付けはの地方おび国の電気規格に準拠する必要
警告
设备安装必须符合本地与本国电气法规。
警告
設備安裝必須符合本地與本國電氣法規。
Warnung
Die Installation der Geräte muss den Sicherheitsstandards entsprechen.
ﻙﺎﻨﻫ ﺮﻄﺧ ﻦﻣ ﻲﺋﺎﺑﺮﻬﻜﻟﺍ ﺭﺎﻴﺘﻟﺍ ﻰﻠﻋ ﺓﺩﻮﺟﻮﻤﻟﺍ ﺔﻗﺎﻄﻟﺍﻭﺃ ﺔﺣﻮﻠﻟﺍ
ﻥﻮﻜﻳ ﺎﻣﺪﻨﻋﻡﺎﻈﻨﻟﺍ ﻞﻤﻌﻳ ﺪﻨﻋ ﺍﺭﺬﺣ ﻦﻛ ﺔﻣﺪﺧ ﺯﺎﻬﺠﻟﺍ ﺍﺬﻫ
!
    (Backplane)    
.   .
Waarschuwing
Een gevaarlijke spanning of energie is aanwezig op de backplane wanneer het
systeem in gebruik is. Voorzichtigheid is geboden tijdens het onderhoud.
ירוחאה
ירוחאה
ירוחאה
ירוחאהירוחאה לנפב
לנפב
לנפב
לנפבלנפב חתמ
חתמ
חתמ
חתמחתמ
זא!הרה
ךלהמב רהזיהל שי .תכרעמה לועפת ןמזב לנפב ירוחאה חתמ תנכס תמי
.הדובעה
Attention
Lorsque le système est en fonctionnement, des tensions électriques circulent sur
le fond de panier. Prendre des précautions lors de la maintenance.
4-15
Chapter 4: Warning Statements for AC Systems
Product Disposal
Warning!
Ultimate disposal of this product should be handled according to all national laws
and regulations.
製品の廃棄
品を廃棄る場合、関係全ての法律例に従い処理す要が
警告
本产品的废弃处理应根据所有国家的法律和规章进行。
警告
本產品的廢棄處理應根據所有國家的法律和規章進行。
יצראה
יצראה
יצראה
יצראהיצראה למשחה
למשחה
למשחה
למשחהלמשחה יקוח
יקוח
יקוח
יקוחיקוח םואית
םואית
םואית
םואיתםואית
!הרהזא
תנקתה םייצראהו םיימוקמה למשחה יקוחל תמאות תויהל תבייח דויצה.
ﺕﺍﺪﻌﻤﻟ ﺐﻴﻛﺮﺗ ﺔﻴﺋﺎﺑﺮﻬﻜﻟﺍ ﻠﻟ ﻞﺜﺘﻤ ﻥﺃ ﺐﺠﻳ ﻦﻴﻧﺍﻮﻘﺔﻴﻨﻁﻮﻟﺍﻭ ﺔﻴﻠﺤﻤﻟﺍ ﺔﻘﻠﻌﺘﻤﻟﺍ
ءﺎﺑﺮﻬﻜﻟﺎﺑ
¡Advertencia!
La instalacion del equipo debe cumplir con las normas de electricidad locales y
nacionales.Attention
L'équipement doit être installé conformément aux normes électriques nationales
et locales.
경고!
지역 국가의 전기 규정에 따라 장비를 설치해야 합니다.
Waarschuwing
Bij installatie van de apparatuur moet worden voldaan aan de lokale en nationale
elektriciteitsvoorschriften.
4-16
SUPERSERVER 6018TR-T/TF User's Manual
Warnung
Die Entsorgung dieses Produkts sollte gemäß allen Bestimmungen und Gesetzen
des Landes erfolgen.
¡Advertencia!
Al deshacerse por completo de este producto debe seguir todas las leyes y
reglamentos nacionales.
Attention
La mise au rebut ou le recyclage de ce produit sont généralement soumis à des
lois et/ou directives de respect de l'environnement. Renseignez-vous auprès de
l'organisme compétent.
Easy Swap Fan Warning
Warning!
The fans might still be turning when you remove the fan assembly from the chassis.
Keep ngers, screwdrivers, and other objects away from the openings in the fan
assembly's housing.
プの警告
冷却フン装置を取た際、いる可能
ンの開口部に指、バーその他ののを近づけないい。
警告
רצומה
רצומה
רצומה
רצומהרצומה קוליס
קוליס
קוליס
קוליסקוליס
!הרהזא
ו תויחנהל םאתהב תויהל בייח הז רצומ לש יפוס קוליס. הנידמה יקוח
ﻲﺋﺎﻬﻨﻟﺍ ﺺﻠﺨﺘﻟﺍ ﻦﻣ ﺞﺘﻨﻤﻟﺍ ﺍﺬ ﻪﻌﻣ ﻞﻣﺎﻌﺘﻟﺍ ﻲﻐﺒﻨ ﺎﻘﻓﻭ ﻊﻴﻤﺠﺔﻴﻨﻁﻮﻟﺍ ﺢﺋﺍﻮﻠﻟﺍﻭ ﻦﻴﻧﺍﻮﻘﻟﺍ ﺪﻨﻋ
!
        .
Waarschuwing
De uiteindelijke verwijdering van dit product dient te geschieden in overeenstemming
met alle nationale wetten en reglementen.
4-17
Chapter 4: Warning Statements for AC Systems
!הרהזא
יקלח תא רשאכ םיריסמ שי .םידבוע ןיידע םיררוואמהו ןכתי ,זראמהמ ררוואמה
קיחרהללררוואמה ךותב םיחתפהמ םינוש הדובע ילכו תועבצאה חוטב תא קחרמ
ﻦﻜﻤﻤﻻﺍ ﻦﻣ ﺡﻭﺍﺮﻤﻻﺍ ﻥﺃ ﻝﺍﺰﺗ ﺔﻻﺍﺯﺇ ﺪﻨﻋﺭﻭﺪﺗ ﺔﻠﺘﻛ ﺔﺣﻭﺮﻤﻻﺍ ﻞﻜﻴﻬﻻﺍ ﻦﻣ ﺐﺠﻳ ءﺎﻘﺑﺇ
ﻊﺑﺎﺻﻷﺍ ﻲﻏﺍﺮﺒﻻﺍ ﺕﺎﻜﻔﻣ
.ءﺎﻴﺷﻷﺍ ﻦﻣ ﺎﻫﺮﻴﻏﻭ ﺍﺪﻴﻌﺑ ﻦﻋ ﺕﺎﺤﺘﻔﻻﺍ ﻠﺘﻛ ﺣﻭﺮﻤﻻﺍ
경고!
섀시로부터 조립품 제거할 팬은 여전히 회전하고 있을 있습니다.
조림품 외관의 열려있는 부분들로부터 손가스크류드라이버, 다른 물체들이
가까이 하지 않도록 배치해 십시오.
当您从机架移除风扇装置,风扇可能仍在转动。小心不要将手指、螺丝起子和其他
物品太靠近风扇
警告
當您從機架移除風扇裝置,風扇可能仍在轉動。小心不要將手指、螺絲起子和其他
物品太靠近風扇。
Warnung
Die Lüfter drehen sich u. U. noch, wenn die fterbaugruppe aus dem Chassis
genommen wird. Halten Sie Finger, Schraubendreher und andere Gegenstände
von den Öffnungen des Lüftergehäuses entfernt.
¡Advertencia!
Los ventiladores podran dar vuelta cuando usted quite ell montaje del ventilador
del chasis. Mandtenga los dedos, los destornilladores y todos los objetos lejos de
las aberturas del ventilador
Attention
Il est possible que les ventilateurs soient toujours en rotation lorsque vous retirerez
le bloc ventilateur du cssis. Prenez garde à ce que doigts, tournevis et autres
objets soient éloignés du logement du bloc ventilateur.
4-18
SUPERSERVER 6018TR-T/TF User's Manual
Power Cable and AC Adapter
Warning!
When installing the product, use the provided or designated connection cables,
power cables and AC adaptors. Using any other cables and adaptors could cause
a malfunction or a re. Electrical Appliance and Material Safety Law prohibits the
use of UL or CSA -certi ed cables (that have UL/CSA shown on the code) for any
other electrical devices than products designated by Supermicro only.
電源コーAC
製品を設置する場合、たは指定れた接続ケブル電源コーAC
を使用下他のブルやを使用す故障や火災の原因に
気用品安全法は、ULCSA認定のケーブル(UL/CSEコー
)Supermicroが指定す製品以外に使用す禁止
警告
安装此产品时,请使用本身提供的或指定的连接线,电源线和电源适配器.使用其它线
Supermicro,
料安全法律规定禁止使用未经UL或CSA认证的线材。(线材上会显示UL/CSA符号)。
警告
安裝此產品時,請使用本身提供的或指定的連接線,電源線和電源適配器.使用其它線
Supermicro,
料安全法律規定禁止使用未經UL或CSA認證的線材。(線材上會顯示UL/CSA符號)。
Warnung
Bei der Installation des Produkts, die zur Vergung gestellten oder benannt
Anschlusskabel, Stromkabel und Netzteile. Verwendung anderer Kabel und Adapter
kann zu einer Fehlfunktion oder ein Brand entstehen. Elektrische Gete und
Material Safety Law verbietet die Verwendung von UL-oder CSA-zerti zierte Kabel,
UL oder CSA auf der Code für alle anderen elektrischen Geräte als Produkte von
Supermicro nur bezeichnet gezeigt haben.
Waarschuwing
Het is mogelijk dat de ventilator nog draait tijdens het verwijderen van het
ventilatorsamenstel uit het chassis. Houd uw vingers, schroevendraaiers en
eventuele andere voorwerpen uit de buurt van de openingen in de ventilatorbehuizing.
4-19
Chapter 4: Warning Statements for AC Systems
¡Advertencia!
Al instalar el producto, utilice los cables de conexión previstos o designados, los
cables y adaptadores de CA. La utilización de otros cables y adaptadores podría
ocasionar un mal funcionamiento o un incendio. Aparatos Eléctricos y la Ley de
Seguridad del Material prohíbe el uso de UL o CSA cables certi cados que tienen
UL o CSA se muestra en el código de otros dispositivos eléctricos que los productos
designados por Supermicro solamente.
Attention
Lors de l'installation du produit, utilisez les bables de connection fournis ou désigné.
L'utilisation d'autres cables et adaptateurs peut provoquer un dysfonctionnement
ou un incendie. Appareils électroménagers et de loi sur la sécurité Matériel interdit
l'utilisation de UL ou CSA câbles certi és qui ont UL ou CSA indiqué sur le code
pour tous les autres appareils électriques que les produits désignés par Supermicro
seulement.
אתמו
אתמו
אתמו
אתמואתמו םיילמשח
םיילמשח
םיילמשח
םיילמשחםיילמשח
מ
מ
מ
ממ
י
י
י
יי
AC
!הרהזא
םימאתמו , םיקפס םילבכב שמתשהל שי ,רצומה תא םיניקתמ רשאכ
AC רשא
וא הלקתל םורגל לוכי רחא םאתמ וא לבכ לכב ךכ שומיש . םשל וקפוסו ודעונ
טב יקוחו למשח ירישכמב שומיש יפ ילמשח יקוח לע . רצק רוסיא םייק ,תוחי
ב םיכמסומה םילבכב שמתשהל-
UL ב וא- CSA לש דוק םהילע )עיפומ ראשכ
UL/CSA( רחא ילמשח רצומ לכ רובע.דבלב ורקימקרפוס ידי לע ןיוצ אלש
ﺐﻴﻛﺮ ﺪﻨﻋ ﻡﺍﺪﺨﺘﺳﺍ ﺐﺠﻳ ﺯﺎﻬﺠﻻﺍ ﻭ،ﻞﻴﺻﻮﺘﻻﺍ ﻼﺑﺎﻛ ﺔﻴﺋﺎﺑﺮﻬﻜﻻﺍ ﺕﻼﺑﺎﻜﻻ
ﺕﻻﻮﺤﻣﻭ ﺩﺩﺮﺘﻤﻻﺍ ﺭﺎﻴﺘﻻﺍ
. ﻥﺃ ﻱﺃ ﻡﺍﺪﺨﺘﺳﺍ ﺕﻼﺑﺎﻛ ﺕﻻﻮﺤﻣﻭ ﻯﺮﺧ ﺐﺒﺴﺘﻳ ﻲﻓ ﻞﻄﻋ ﺙﻭﺪﺣ ﻳﺮ ﻭﺃ ﻲﺘﻻﺍ .
ﻚﻻ ﺎﻫﺮﻴﻓﻮﺗ ﻢﺗ ﺞﺘﻨﻤﻻﺍ ﻊﻣ
UL ﻭﺃ CSA ﺔﻴﺋﺎﺑﺮﻬﻜﻻ ﺓﺰﻬﺟﻷﺍ ﺩﺍﻮﻣﻭ ﻥﻮﻧﺎﻗ ﺔﻣﻼﺴﻻﺍ ﻡﺍﺪﺨﺘﺳﺍ ﺮﻈﺤ ﺕﻼﺑﺎﻜﻻﺍ
ﻞﺒﻗ ﻦﻣ ﺓﺪﻤﺘﻌﻣ
Supermicro ﺓﺰﻬﺟﺃ ﻯﺮﺧﺃ ﺔﻴﺋﺎﺑﺮﻬ ﻴﻏ ﺕﺎﺠﺘﻨﻤﻻﺍ ﺔﻨﻴﻌﻤﻻﺍ ﻞﺒﻗ ﻦﻣ ﻱﻷ
(UL/CSA ﻞﻤﺤﺗ ﻲﺘﻻﺍﺔﻣﻼﻋ )
!
      , AC
 .         
  .  (Electrical Appliance and Material Safety
Law)         
 UL CSA  (  UL/CSA ) 
.
4-20
SUPERSERVER 6018TR-T/TF User's Manual
Waarschuwing
Bij het installeren van het product, gebruik de meegeleverde of aangewezen kabels,
stroomkabels en adapters. Het gebruik van andere kabels en adapters kan leiden
tot een storing of een brand. Elektrisch apparaat en veiligheidsinformatiebladen wet
verbiedt het gebruik van UL of CSA gecerti ceerde kabels die UL of CSA die op
de code voor andere elektrische apparaten dan de producten die door Supermicro
alleen.
Chapter 5: Advanced Motherboard Setup
5-1
Chapter 5
Advanced Motherboard Setup
This chapter covers the steps required to install the X10DRT-L/LIBF motherboard
into the chassis, connect the data and power cables and install add-on cards.
All motherboard jumpers and connections are also described. A layout and quick
reference chart are included in this chapter for your reference. Remember to
completely close the chassis when you have  nished working with the motherboard
to better cool and protect the system.
5-1 Handling the Motherboard
Electrostatic Discharge (ESD) can damage electronic com ponents. To prevent
damage to any printed circuit boards (PCBs), it is important to handle them very
carefully (see previous chapter). To prevent the motherboard from bending, keep
one hand under the center of the board to support it when handling. The following
measures are generally suf cient to protect your equipment from electric static
discharge.
Precautions
Use a grounded wrist strap designed to prevent Electrostatic Discharge (ESD).
Touch a grounded metal object before removing any board from its antistatic bag.
Handle a board by its edges only; do not touch its components, peripheral chips,
memory modules or gold contacts.
When handling chips or modules, avoid touching their pins.
Put the motherboard, add-on cards and peripherals back into their antistatic
bags when not in use.
For grounding purposes, make sure your computer chassis provides excellent
conductivity between the power supply, the case, the mounting fasteners and
the motherboard.
Unpacking
The motherboard is shipped in antistatic packaging to avoid electrical static
discharge. When unpacking the board, make sure the person handling it is static
protected.
5-2
SUPERSERVER 6018TR-T/TF User's Manual
5-3 Control Panel Connectors and I/O Ports
The rear I/O ports are color coded in conformance with the PC 99 speci cation. See
Figure 5-1 below for the colors and locations of the various I/O ports.
Figure 5-1. Rear I/O Ports
2
1 5
3
4 6 7 98
5-2 Connecting Cables
Now that the processors are installed, the next step is to connect the cables to
the serverboard.
Connecting Data Cables
The cables used to transfer data from the peripheral devices have been carefully
routed in precon gured systems to prevent them from blocking the ow of cooling
air that moves through the system from front to back. If you need to disconnect
any of these cables, you should take care to reroute them as they were originally
after reconnecting them (make sure the red wires connect to the pin 1 locations). If
you are con guring the system, keep the air ow in mind when routing the cables.
The following cables need to be connected for the SuperServer 6018TR-T/TF
system:
Two round 50-cm 16-to-16-pin ribbon front control cables (CBL-0087)
One set of SATA 4-51/47/41/37-cm round cables (CBL-0201L)
Two 4-pin 20-cm power cables (CBL-0212L)
Chapter 5: Advanced Motherboard Setup
5-3
Back Panel I/O Port Locations and De nitions
1. Back Panel USB Port 0
2. Back Panel USB Port 1
3. IPMI_Dedicated LAN
4. Gigabit LAN 1
5. Gigabit LAN 2
6. COM1
7. VGA (Blue)
8. In niBand FDR/QDR (Optional for X10DRT-LIBF/LIBQ)
9. UID Button/UID LED (LE1)
Connecting the Control Panel
JF1 contains header pins for various front control panel connectors. See Figure 5-1
for the pin locations of the various front control panel buttons and LED indicators.
Even and odd numbered pins are on opposite sides of each header.
All JF1 wires have been bundled into single keyed ribbon cable to simplify their
connection. The red wire in the ribbon cable plugs into pin 1 of JF1. Connect the
other end of the cable to the Control Panel printed circuit board, located just behind
the system status LEDs in the chassis.
See the Connector De nitions section in this chapter for details and pin descriptions
of JF1.
Figure 5-2. Front Control Panel Header Pins (JF1)
1 2
Ground
19 20
XX
FP PWRLED
3.3 V
HDD LED
UID Switch
NIC1 Link LEDNIC1 Activity LED
NIC2 Link LED
NIC2 Activity LED
UID LED OH/Fan Fail/
PWR Fail LED)
Power Fail LED
3.3V
Reset Button
Power Button Ground
Ground
X
5-4
SUPERSERVER 6018TR-T/TF User's Manual
Installing the LGA2011 Processor
1. There are two load levers on the LGA2011 socket. To open the socket cover,
rst press and release the load lever labeled 'Open 1st'.
OPEN 1st
OPEN 1st
OPEN 1st
OPEN 1st
OPEN 1st
Press down on
Load Lever
labeled 'Open 1st'.
OPEN 1st
OPEN 1st
OPEN 1st
OPEN 1st
OPEN 1st
5-4 Processor and Heatsink Installation
Caution! When handling the processor package, avoid placing direct pressure on the
label area.
Note: Always connect the power cord last, and always remove it before adding,
removing or changing any hardware components. Make sure that you install the
processor into the CPU socket before you install the CPU heatsink.
Caution! If you buy a CPU separately, make sure that you use an Intel-certi ed multi-
directional heatsink only.
Note: Make sure to install the system board into the chassis before you install the
CPU heatsink.
Note: When receiving a server board without a processor pre-installed, make sure that
the plastic CPU socket cap is in place and none of the socket pins are bent; otherwise,
contact your retailer immediately.
Note: Refer to the Supermicro website for updates on CPU support.
Note: When one CPU is installed, be sure to installed on CPU Socket 1 rst.
Note: Graphics and drawings shown in this manual are for illustration only. Your
components may or may not look the same as the graphics shown in the manual.
Chapter 5: Advanced Motherboard Setup
5-5
2. Press the second load lever labeled 'Close 1st' to release the load plate that
covers the CPU socket from its locking position.
OPEN 1st
OP
OP
OP
OPEN
EN
EN
EN
1s
1s
1s
1s t
t
t
t
OPEN 1st
Press down on
Load the Lever
labeled 'Close 1st'
Pull lever away
from the socket
3. With the lever labeled 'Close 1st' fully retracted, gently push down on
the 'Open 1st' lever to open the load plate. Lift the load plate to open it
completely.
Gently push down to pop the
load plate open.
OPEN 1st
OPEN
OPEN
OPEN
OPEN 1s
1s
1s
1s t
t
t
t
4. Using your thumb and the index nger, remove the 'WARNING' plastic cap
from the socket.
5-6
SUPERSERVER 6018TR-T/TF User's Manual
5. Use your thumb and index nger to hold the CPU on its edges. Align the CPU
keys, which are semi-circle cutouts, against the socket keys.
Socket Keys
CPU Keys
6. Once they are aligned, carefully lower the CPU straight down into the socket.
(Do not drop the CPU on the socket. Do not move the CPU horizontally or
vertically. Do not rub the CPU against the surface or against any pins of the
socket to avoid damaging the CPU or the socket.)
Caution: You can only install the CPU inside the socket in one direction. Make sure
that it is properly inserted into the CPU socket before closing the load plate. If it doesn't
close properly, do not force it as it may damage your CPU. Instead, open the load
plate again and double-check that the CPU is aligned properly.
Chapter 5: Advanced Motherboard Setup
5-7
7. With the CPU inside the socket, inspect the four corners of the CPU to make
sure that the CPU is properly installed.
8. Close the load plate with the CPU inside the socket. Lock the lever labeled
'Close 1st' rst, then lock the lever labeled 'Open 1st' second. Use your
thumb to gently push the load levers down to the lever locks.
OPEN 1st
OPEN
OPEN
OPEN
OPEN 1st
1st
1st
1st
Push down and lock the
level labeled 'Close 1st'.
Gently close the
load plate.
OPEN 1st
OPEN 1s
OPEN 1s
OPEN 1s
OPEN 1s
t
t
t
t
OPEN 1st
OPEN 1st
OPEN 1st
OPEN 1st
OPEN 1st
Lever Lock
Lever Lock
Push down and lock
the lever labeled
'Open 1st'


Specyfikacje produktu

Marka: Supermicro
Kategoria: serwer
Model: SuperServer 6018TR-T

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Supermicro SuperServer 6018TR-T, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą




Instrukcje serwer Supermicro

Instrukcje serwer

Najnowsze instrukcje dla serwer