Instrukcja obsługi Supermicro SuperServer 2028TP-HC1R-SIOM

Supermicro serwer SuperServer 2028TP-HC1R-SIOM

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Supermicro SuperServer 2028TP-HC1R-SIOM (142 stron) w kategorii serwer. Ta instrukcja była pomocna dla 13 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/142

USER'S MANUAL

Revision 1.0a

SUPERSERVER®

2028TP-HTR-SIOM

2028TP-HC0R-SIOM

2028TP-HC1R-SIOM

The information in this User’s Manual has been carefully reviewed and is believed to be accurate.

The vendor assumes no responsibility for any inaccuracies that may be contained in this document,

makes no commitment to update or to keep current the information in this manual, or to notify any

person or organization of the updates. Please Note: For the most up-to-date version of this

manual, please see our web site at www.supermicro.com.

Super Micro Computer, Inc. ("Supermicro") reserves the right to make changes to the product

described in this manual at any time and without notice. This product, including software and

documentation, is the property of Supermicro and/or its licensors, and is supplied only under a

license. Any use or reproduction of this product is not allowed, except as expressly permitted by

the terms of said license.

IN NO EVENT WILL SUPERMICRO BE LIABLE FOR DIRECT, INDIRECT, SPECIAL, INCIDENTAL,

SPECULATIVE OR CONSEQUENTIAL DAMAGES ARISING FROM THE USE OR INABILITY TO

USE THIS PRODUCT OR DOCUMENTATION, EVEN IF ADVISED OF THE POSSIBILITY OF

SUCH DAMAGES. IN PARTICULAR, SUPERMICRO SHALL NOT HAVE LIABILITY FOR ANY

HARDWARE, SOFTWARE, OR DATA STORED OR USED WITH THE PRODUCT, INCLUDING THE

COSTS OF REPAIRING, REPLACING, INTEGRATING, INSTALLING OR RECOVERING SUCH

HARDWARE, SOFTWARE, OR DATA.

Any disputes arising between manufacturer and customer shall be governed by the laws of Santa

Clara County in the State of California, USA. The State of California, County of Santa Clara shall

be the exclusive venue for the resolution of any such disputes. Super Micro's total liability for all

claims will not exceed the price paid for the hardware product.

FCC Statement: This equipment has been tested and found to comply with the limits for a Class

A digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference when the equipment is operated in a commercial

environment. This equipment generates, uses, and can radiate radio frequency energy and, if not

installed and used in accordance with the manufacturer’s instruction manual, may cause harmful

interference with radio communications. Operation of this equipment in a residential area is likely

to cause harmful interference, in which case you will be required to correct the interference at your

own expense.

California Best Management Practices Regulations for Perchlorate Materials: This Perchlorate

warning applies only to products containing CR (Manganese Dioxide) Lithium coin cells. “Perchlorate

Material-special handling may apply. See www.dtsc.ca.gov/hazardouswaste/perchlorate”

WARNING: Handling of lead solder materials used in this

product may expose you to lead, a chemical known to

the State of California to cause birth defects and other

reproductive harm.

Manual Revision 1.0a

Release Date: February 06, 2018

Unless you request and receive written permission from Super Micro Computer, Inc., you may not

copy any part of this document.

Information in this document is subject to change without notice. Other products and companies

referred to herein are trademarks or registered trademarks of their respective companies or mark

holders.

Printed in the United States of America

iii

Preface

About This Manual

This manual is written for professional system integrators and PC technicians.

It provides information for the installation and use of the SuperServer

2028TP-HTR/HC0R/HC1R-SIOM. Installation and maintenance should be

performed by experienced technicians only.

The SuperServer 2028TP-HTR/HC0R/HC1R-SIOM is a high-end server based

on the SC217HQ+-R2K04BP2 2U rackmount chassis and the dual processor

X10DRT-PS serverboard. All models have four serverboard nodes with six hot-swap

Hard Disk Drives (HDD) each per node.

Manual Organization

Chapter 1: Introduction

The rst chapter provides a checklist of the main components included with the

server system and describes the main features of the X10DRT-PS serverboard and

the SC217HQ+-R2K04BP2 chassis.

Chapter 2: Server Installation

This chapter describes the steps necessary to install the SuperServer

2028TP-HTR/HC0R/HC1R-SIOM into a rack and check out the server conguration

prior to powering up the system. If your server was ordered without processor and

memory components, this chapter will refer you to the appropriate sections of the

manual for their installation.

Chapter 3: System Interface

Refer here for details on the system interface, which includes the functions and

information provided by the control panel on the chassis as well as other LEDs

located throughout the system.

Chapter 4: Standardized Safety Warnings

You should thoroughly familiarize yourself with this chapter for a general overview

of safety precautions that should be followed when installing and servicing the

SuperServer 2028TP-HTR/HC0R/HC1R-SIOM.

Chapter 5: Advanced Serverboard Setup

Chapter 5 provides detailed information on the X10DRT-PS serverboard, including

the locations and functions of connections, headers and jumpers. Refer to

this chapter when adding or removing processors or main memory and when

reconguring the serverboard.

SUPERSERVER 2028TP-HTR/HC0R/HC1R-SIOM USER'S MANUAL

Chapter 6: Advanced Chassis Setup

Refer to Chapter 6 for detailed information on the SC217HQ+-R2K04BP2 server

chassis. You should follow the procedures given in this chapter when installing,

removing or reconguring hard drives and when replacing system power supply

units and cooling fans.

Chapter 7: BIOS

The BIOS chapter includes an introduction to BIOS and provides detailed information

on running the CMOS Setup Utility.

Appendix A: BIOS Error Beep Codes

Appendix B: System Specications

Appendix C: Chinese Safety Warnings

Table of Contents

Chapter 1 Introduction

1-1 Overview ......................................................................................................... 1-1

1-2 Serverboard Features ..................................................................................... 1-2

Processors 1-2 ......................................................................................................

Memory 1-2 ...........................................................................................................

SAS 1-2 .................................................................................................................

SATA ................................................................................................................ 1-2

PCI Expansion Slots ....................................................................................... 1-3

I/O Ports .......................................................................................................... 1-3

Graphics Controller ......................................................................................... 1-3

1-3 Server Chassis Features ................................................................................ 1-4

System Power ................................................................................................. 1-4

Front Control Panel ......................................................................................... 1-4

Cooling System ............................................................................................... 1-4

Air Shrouds ..................................................................................................... 1-4

Mounting Rails ................................................................................................ 1-4

1-4 Contacting Supermicro .................................................................................... 1-6

1-5 2U Twin2: System Notes ................................................................................. 1-7

Nodes 1-7 ..............................................................................................................

System Power ................................................................................................. 1-7

Hard Drive Backplane/Drives .......................................................................... 1-7

Chapter 2 Server Installation

2-1 Overview ......................................................................................................... 2-1

2-2 Unpacking the System .................................................................................... 2-1

2-3 Preparing for Setup ......................................................................................... 2-1

Choosing a Setup Location ............................................................................. 2-2

2-4 Warnings and Precautions .............................................................................. 2-2

Rack Precautions ............................................................................................ 2-2

Server Precautions .......................................................................................... 2-2

Rack Mounting Considerations ....................................................................... 2-3

Ambient Operating Temperature ................................................................ 2-3

Reduced Airow ......................................................................................... 2-3

Mechanical Loading ................................................................................... 2-3

Circuit Overloading ..................................................................................... 2-3

Reliable Ground ......................................................................................... 2-3

2-5 Installing the System into a Rack ................................................................... 2-4

Identifying the Sections of the Rack Rails ...................................................... 2-4

SUPERSERVER 2028TP-HTR/HC0R/HC1R-SIOM USER'S MANUAL

vii

Locking Tabs ................................................................................................... 2-5

Releasing the Inner Rail ................................................................................. 2-5

Installing The Inner Rails on the Chassis ....................................................... 2-6

Installing the Outer Rails on the Rack ............................................................ 2-7

Standard Chassis Installation ......................................................................... 2-8

Chapter 3 System Interface

3-1 Overview ......................................................................................................... 3-1

3-2 Control Panel Button ....................................................................................... 3-2

Power 3-2 ..............................................................................................................

UID 3-2 ..................................................................................................................

3-3 Control Panel LEDs ........................................................................................ 3-2

Alert 3-2 .................................................................................................................

NIC 3-3 ..................................................................................................................

3-4 Hard Drive Carrier LEDs ................................................................................. 3-3

Chapter 4 Standardized Warning Statements for AC Systems

4-1 About Standardized Warning Statements ....................................................... 4-1

Warning Denition ........................................................................................... 4-1

Installation Instructions .................................................................................... 4-4

Circuit Breaker ................................................................................................ 4-5

Power Disconnection Warning ........................................................................ 4-6

Equipment Installation ..................................................................................... 4-8

Restricted Area ................................................................................................ 4-9

Battery Handling ............................................................................................ 4-10

Redundant Power Supplies .......................................................................... 4-12

Backplane Voltage ........................................................................................ 4-13

Comply with Local and National Electrical Codes ........................................ 4-14

Product Disposal ........................................................................................... 4-15

Hot Swap Fan Warning ................................................................................. 4-16

Power Cable and AC Adapter ...................................................................... 4-18

Chapter 5 Advanced Serverboard Setup

5-1 Handling the Serverboard ............................................................................... 5-1

Precautions 5-1 .....................................................................................................

Unpacking 5-1 .......................................................................................................

5-2 Connecting Cables .......................................................................................... 5-2

Connecting Data Cables ................................................................................. 5-2

5-3 Rear I/O Ports ................................................................................................. 5-3

5-4 Processor and Heatsink Installation................................................................ 5-4

Installing a Passive CPU Heatsink ................................................................. 5-7

Removing the Heatsink ................................................................................... 5-8

Table of Contents

viii

5-5 Installing Memory ............................................................................................ 5-9

Memory Support .............................................................................................. 5-9

Memory Support for E5-2600 (v3)-based Serverboards .......................... 5-10

Memory Support for E5-2600 (v4)-based Serverboards ...........................5-11

5-6 Adding PCI Expansion Cards ........................................................................5-11

5-7 Serverboard Details ...................................................................................... 5-12

X10DRT-PS Quick Reference ....................................................................... 5-13

5-8 Connector Denitions .................................................................................... 5-14

5-9 Jumper Settings ............................................................................................ 5-16

Explanation of Jumpers ................................................................................ 5-16

5-10 Onboard Indicators ........................................................................................ 5-18

5-11 PCI-Express and SATA Connections ............................................................ 5-20

5-12 Installing Software ......................................................................................... 5-21

SuperDoctor® 5 ............................................................................................ 5-22

5-13 Onboard Battery ............................................................................................ 5-23

Chapter 6 Advanced Chassis Setup

6-1 Static-Sensitive Devices .................................................................................. 6-1

Precautions 6-1 .....................................................................................................

Unpacking 6-1 .......................................................................................................

6-2 Control Panel .................................................................................................. 6-2

6-3 Chassis Cover ................................................................................................. 6-3

6-4 Air Shrouds ..................................................................................................... 6-4

6-5 Checking the Airow ....................................................................................... 6-5

6-6 System Fans ................................................................................................... 6-5

Optional Fan Congurations ........................................................................... 6-5

6-7 Removing and Installing the Backplane .......................................................... 6-8

Removing the Backplane ................................................................................ 6-8

Installing the Backplane ................................................................................ 6-10

6-8 Installing the Serverboard ..............................................................................6-11

I/O Shield .......................................................................................................6-11

Permanent and Optional Standoffs ................................................................6-11

6-9 Adapter Card Replacement........................................................................... 6-14

Expansion Card/PCI Slot Setup .................................................................... 6-15

Installing the Riser Card ............................................................................... 6-15

6-10 Drive Bay Installation/Removal ..................................................................... 6-17

Accessing the Drive Bays ............................................................................. 6-17

6-11 Power Supply ................................................................................................ 6-20

Power Supply Replacement .......................................................................... 6-20

SUPERSERVER 2028TP-HTR/HC0R/HC1R-SIOM USER'S MANUAL

Chapter 7 BIOS

7-1 Introduction ...................................................................................................... 7-1

Starting BIOS Setup Utility .............................................................................. 7-1

How To Change the Conguration Data ......................................................... 7-1

How to Start the Setup Utility ......................................................................... 7-2

7-2 Main Setup ...................................................................................................... 7-2

7-3 Advanced Setup Congurations...................................................................... 7-4

7-4 Event Logs .................................................................................................... 7-32

7-5 IPMI ............................................................................................................... 7-34

7-6 Security Settings ........................................................................................... 7-36

7-7 Boot Settings ................................................................................................. 7-37

7-8 Save & Exit ................................................................................................... 7-39

Appendix A BIOS Error Beep Codes

Appendix B System Specications

Appendix C Chinese Safety Warnings

Table of Contents

Notes

SUPERSERVER 2028TP-HTR/HC0R/HC1R-SIOM USER'S MANUAL

Chapter 1

Introduction

1-1 Overview

The SuperServer 2028TP-HTR/HC0R/HC1R-SIOM is a high-end server comprised

of two main subsystems: the SC217HQ+-R2K04BP2 2U server chassis and the

X10DRT-PS dual processor serverboard, which reside in four hot-swap nodes.

Please refer to our website for information on operating systems that have been

certied for use with the system (www.supermicro.com).

In addition to the serverboard and chassis, various hardware components have

been included with the SuperServer 2028TP-HTR/HC0R/HC1R-SIOM server, as

listed below:

• Heat Sinks

Four 1U passive CPU heatsinks for rear CPU (SNK-P0047PSM)

Four 1U passive CPU heatsinks w/narrow ILM (SNK-P0057PS)

• Four mylar air shrouds (MCP-310-21703-0B)

• Four 8-cm cooling fans (FAN-0162L4)

• SATA/SAS Backplane

Four HD backplanes (BPN-ADP-6SATA3P/BPN-ADP-S3008L-L6IP/BPN-ADP-

S3108L-H6iRP)

One SAS backplane HDD (BPN-SAS3-217HQ)

Twenty-four hot-swap 2.5" HDD trays (MCP-220-00047-0B)

• Eight riser cards (4x RSC-R1UTP-E16R, 4x RSC-P-6)

• One rackmount rail kit (MCP-290-00053-0N)

Note: For your system to work properly, please follow the links below to download

all necessary drivers/utilities and the user’s manual for your server.

• Supermicro product manuals: http://www.supermicro.com/support/manuals/

• Product drivers and utilities: ftp://ftp.supermicro.com

• Product safety info: http://www.supermicro.com/about/policies/safety_

information.cfm

Chapter 1: Introduction

1-1

1-2

SUPERSERVER 2028TP-HTR/HC0R/HC1R-SIOM USER'S MANUAL

1-2 Serverboard Features

At th e hea r t of th e S u pe r S er v e r 2 0 2 8 T P-HT R / H C 0R/ H C 1 R-S I O M

lies the X10DRT-PS, a dual processor serverboard based on the Intel®

PCH C612 chipset and designed to provide maximum performance. Four of these

serverboards can be mounted in the SC217HQ+-R2K04BP2 chassis.

The sections below cover the main features of the X10DRT-PS serverboard (see

Figure 1-1 for a block diagram of the chipset).

Processors

The X10DRT-PS supports single or dual Intel® Xeon® E5-2600 v3/v4 series

processors (Socket R LGA 2011). Please refer to the serverboard description pages

on our web site for a complete listing of supported processors (www.supermicro.

com).

Memory

The X10DRT-PS has sixteen DIMM slots supporting up to 2 TB of LRDIMM (Load

Reduced DIMM) or 1 TB of RDIMM (Registered DIMM) DDR4-2400/2133/1866 MHz

registered ECC memory. See Chapter 5 for details.

Note: Check the Supermicro website (www.supermicro.com) for the latest memory

support information.

SAS

The 2028TP-HC0R-SIOM includes an LSI 3008 controller to support six SAS3 hard

drives per node. (RAID 0, 1, 5, 6, 10, 50 and 60 supported).

The 2028TP-HC1R-SIOM includes an LSI 3108 controller to support six SAS3 hard

drives per node. (RAID 0, 1, 5, 6, 10, 50 and 60 supported).

The SAS drives are hot-swappable units.

SATA

The 2028TP-HTR-SIOM uses a controller integrated into the PCH C612 chipset to

support six SAS3 hard drives per node. (RAID 0, 1, 5, 6, 10, 50 and 60 supported).

The SATA drives are hot-swappable units.

1-4

SUPERSERVER 2028TP-HTR/HC0R/HC1R-SIOM USER'S MANUAL

1-3 Server Chassis Features

The following is a general outline of the main features of the SC217HQ+ server

chassis.

System Power

The SC217HQ+ chassis includes a redundant, high-efciency 80-plus Platinum

certied power supply rated at 2000 Watts (one active and one backup power supply

module). In the event your power supply fails, replacement is simple and can be

accomplished without tools.

Front Control Panel

The SC217HQ+-R2K04BP2 chassis includes four front panels on the handles of the

chassis which control each of the nodes. Each control panel on the SuperServer

2028TP-HTR/HC0R/HC1R-SIOM provides you with system monitoring and control

for one server node. LEDs indicate system power, HDD activity, network activity,

system overheat and power supply failure. A main power button and a system reset

button are also included.

Cooling System

The SC217HQ+ chassis accepts four system fans, which are powered from the

backplane.

Air Shrouds

The SC217HQ+ chassis includes one mylar air shroud per node that directs the

airow where cooling is needed on each serverboard. Always use the air shroud

included with each serverboard.

Mounting Rails

The SC217HQ+ includes a set of quick-release rails, and can be placed in a rack

for secure storage and use. To setup your rack, follow the step-by-step instructions

included in Chapter 2.

1-5

Chapter 1: Introduction

Figure 1-1. Intel PCH C612 Chipset:

System Block Diagram

Note: This is a general block diagram and may not exactly repre-

sent the features on your serverboard. See the previous pages for

the actual specications of your serverboard. This block diagram is

intended for your reference only.

SPI

L 3 AN

RGRMII

Debug Card

FRONT PANEL

SYSTEM POWER

CTRL

FAN SPEED

PCI-E X1 G2

USB 2.0

PCH

6.0 Gb/S

USB 2.0

LPC

R ETL8211

-VB-CG

R 5J4

SPI

T Sensoremp

EMC1402-1 *2 at di SMBUS

TPM HE ERAD

USB 3.0

USB

AST 0240

BMC

RMII/NCSI

COM1

C toronnec

VGA CONN

BMC B t hoo Flas

DDR3

DDR4

#2-1

DDR4

#1-4

#1-3

#1-2

#1-1

QPI

9.6G

DMI2

PCI-E X8 G3

#1-5

#1-6

DDR4

QPI

9.6G

SIOM

PCI-E X16

SXB1

SLOT1

SLOT2

PCI-E X8 mini PCI-E

PCI-E X16 G3

#1 #2 #3#3

#1-7

#1-8

#2-2

#2-3

#2-4

#2-5

#2-6

#2-7

#2-8

SXB2

Go go adapter card.

BIOS

SPI

MUX

DDR4

2UPC1UPC

DMI2 DMI2

SATA

1-6

SUPERSERVER 2028TP-HTR/HC0R/HC1R-SIOM USER'S MANUAL

1-4 Contacting Supermicro

Headquarters

Address: Super Micro Computer, Inc.

980 Rock Ave.

San Jose, CA 95131 U.S.A.

Tel: +1 (408) 503-8000

Fax: +1 (408) 503-8008

Email: marketing@supermicro.com (General Information)

support@supermicro.com (Technical Support)

Website: www.supermicro.com

Europe

Address: Super Micro Computer B.V.

Het Sterrenbeeld 28, 5215 ML

's-Hertogenbosch, The Netherlands

Tel: +31 (0) 73-6400390

Fax: +31 (0) 73-6416525

Email: sales@supermicro.nl (General Information)

support@supermicro.nl (Technical Support)

rma@supermicro.nl (Customer Support)

Website: www.supermicro.nl

Asia-Pacic

Address: Super Micro Computer, Inc.

3F, No. 150, Jian 1st Rd.

Zhonghe Dist., New Taipei City 235

Taiwan (R.O.C)

Tel: +886-(2) 8226-3990

Fax: +886-(2) 8226-3992

Email: support@supermicro.com.tw

Website: www.supermicro.com.tw

1-7

Chapter 1: Introduction

1-5 2U Twin2: System Notes

As a 2U Twin2 conguration, the SuperServer 2028TP-HTR/HC0R/HC1R-SIOM is

a unique server system. With four system boards incorporated into a single chassis

acting as four separate nodes, there are several points you should keep in mind.

Nodes

Each of the four serverboards act as a separate node in the system. As independent

nodes, each may be powered off and on without affecting the others. In addition,

each node is a hot-swappable unit that may be removed from the rear of the chassis.

The nodes are connected to the server backplane by means of an adapter card.

Note: A guide pin is located between the upper and lower nodes on the inner chassis

wall. This guide pin also acts as a “stop” when a node is fully installed. If too much

force is used when inserting a node this pin may break off. Take care to slowly slide

a node in until you hear the “click” of the locking tab seating itself.

System Power

Dual 2000 Watt power supplies are used to provide the power for all four

serverboards. Each serverboard however, can be shut down independently of the

other with the power button on its own control panel.

Hard Drive Backplane/Drives

As a system, the SuperServer 2028TP-HTR/HC0R/HC1R-SIOM supports the use

of 24 hard drives (SAS or SATA). A single backplane works to apply system-based

control for power and fan speed functions, yet at the same time logically connects

a set of six hard drives to each of the four nodes. Consequently, RAID setup is

limited to a six-drive scheme (RAID cannot be spread across all 24 drives). See

the Drive Bay Installation/Removal section in Chapter 6 for the logical hard drive

and node conguration.

Chapter 2: Server Installation

2-1

Chapter 2

Server Installation

2-1 Overview

This chapter provides a quick setup checklist to get your SuperServer

2028TP-HTR/HC0R/HC1R-SIOM up and running. Following these steps in the order

given should enable you to have the system operational within a minimum amount

of time. This quick setup assumes that your system has come to you with the

processors and memory preinstalled. If your system is not already fully integrated

with a serverboard, processors, system memory etc., please turn to the chapter or

section noted in each step for details on installing specic components.

2-2 Unpacking the System

You should inspect the box the 2028TP-HTR/HC0R/HC1R-SIOM server was

shipped in and note if it was damaged in any way. If the server itself shows damage

you should le a damage claim with the carrier who delivered it.

Dec i de on a s uitable locatio n for the rac k unit that wi ll hold the

2028TP-HTR/HC0R/HC1R-SIOM server. It should be situated in a clean, dust-

free area that is well ventilated. Avoid areas where heat, electrical noise and

electromagnetic elds are generated. You will also need it placed near a grounded

power outlet. Read the Rack and Server Precautions in the next section.

2-3 Preparing for Setup

The box the SuperServer 2028TP-HTR/HC0R/HC1R-SIOM was shipped in should

include two sets of rail assemblies, two rail mounting brackets and the mounting

screws you will need to install the system into the rack. Follow the steps in the

order given to complete the installation process in a minimum amount of time.

Please read this section in its entirety before you begin the installation procedure

outlined in the sections that follow.

2-2

SUPERSERVER 2028TP-HTR/HC0R/HC1R-SIOM USER'S MANUAL

Choosing a Setup Location

• Leave enough clearance in front of the rack to enable you to open the front door

completely (~25 inches) and approximately 30 inches of clearance in the back

of the rack to allow for sufcient airow and ease in servicing.

• This product is for installation only in a Restricted Access Location (dedicated

equipment rooms, service closets and the like).

• This product is not suitable for use with visual display work place devices

according to §2 of the German Ordinance for Work with Visual Display Units.

2-4 Warnings and Precautions

Rack Precautions

• Ensure that the leveling jacks on the bottom of the rack are fully extended to

the oor with the full weight of the rack resting on them.

• In single rack installation, stabilizers should be attached to the rack. In multiple

rack installations, the racks should be coupled together.

• Always make sure the rack is stable before extending a component from the

rack.

• You should extend only one component at a time - extending two or more

simultaneously may cause the rack to become unstable.

Server Precautions

• Review the electrical and general safety precautions in Chapter 4.

• Determine the placement of each component in the rack you install the before

rails.

• Install the heaviest server components on the bottom of the rack rst, and then

work up.

• Use a regulating uninterruptible power supply (UPS) to protect the server from

power surges, voltage spikes and to keep your system operating in case of a

power failure.

• Allow any hot plug drives and power supply modules to cool before touching

them.

• Always keep the rack's front door and all panels and components on the servers

closed when not servicing to maintain proper cooling.

Chapter 2: Server Installation

2-3

Rack Mounting Considerations

Ambient Operating Temperature

If installed in a closed or multi-unit rack assembly, the ambient operating

temperature of the rack environment may be greater than the ambient temperature

of the room. Therefore, consideration should be given to installing the equipment

in an environment compatible with the manufacturer’s maximum rated ambient

temperature (Tmra).

Reduced Airow

Equipment should be mounted into a rack so that the amount of airow required

for safe operation is not compromised.

Mechanical Loading

Equipment should be mounted into a rack so that a hazardous condition does not

arise due to uneven mechanical loading.

Circuit Overloading

Consideration should be given to the connection of the equipment to the power

supply circuitry and the effect that any possible overloading of circuits might have

on overcurrent protection and power supply wiring. Appropriate consideration of

equipment nameplate ratings should be used when addressing this concern.

Reliable Ground

A reliable ground must be maintained at all times. To ensure this, the rack

itself should be grounded. Particular attention should be given to power supply

connections other than the direct connections to the branch circuit (i.e. the use of

power strips, etc.).

Warning! To prevent bodily injury when mounting or servicing this unit in a

rack, you must take special precautions to ensure that the system remains

stable. The following guidelines are provided to ensure your safety:

• This unit should be mounted at the bottom of the rack if it is the only unit in

the rack.

• When mounting this unit in a partially lled rack, load the rack from the bottom

to the top with the heaviest component at the bottom of the rack.

• If the rack is provided with stabilizing devices, install the stabilizers before

mounting or servicing the unit in the rack.

Chapter 2: Server Installation

2-5

Figure 2-2. Extending and Releasing the Inner Rail

Locking Tabs

Each inner rail has a locking tab. This tab locks the chassis into place when installed

and pushed fully into the rack. These tabs also lock the chassis in place when fully

extended from the rack. This prevents the server from coming completely out of

the rack when when the chassis is pulled out for servicing.

Releasing the Inner Rail

Use the procedure below to release the inner rails from the outer rails.

Releasing Inner Rail from the Outer Rails (Figure 2-2)

1. Identify the left and right outer rail assemblies as described in section 2-5.

2. Pull the inner rail out of the outer rail until it is fully extended as illustrated

below.

3. Press the locking tab down to release the inner rail.

4. Pull the inner rail all the way out.

5. Repeat steps 1-3 for the second outer rail.

2-6

SUPERSERVER 2028TP-HTR/HC0R/HC1R-SIOM USER'S MANUAL

Figure 2-3. Installing the Inner Rails

Installing The Inner Rails on the Chassis

To install the inner rails, use the procedure below.

Installing the Inner Rails (Figures 2-3 and 2-4)

1. Conrm that the left and right inner rails have been correctly identied.

2. Place the inner rail rmly against the side of the chassis, aligning the hooks

on the side of the chassis with the holes in the inner rail.

3. Slide the inner rail forward toward the front of the chassis until the rail clicks

into the locked position, which secures the inner rail to the chassis.

4. Secure the inner rail to the chassis with the screws provided.

5. Repeat steps 1 through 4 above for the other inner rail.

Figure 2-4. Inner Rails Installed on the Chassis

Inner Rails

Chapter 2: Server Installation

2-7

Figure 2-5. Extending and Releasing the Outer Rails

Installing the Outer Rails on the Rack

Use the procedure below to install the outer rails onto the rack.

Installing the Outer Rails (Figure 2-5)

1. Press upward on the locking tab at the rear end of the middle rail.

2. Push the middle rail back into the outer rail.

3. Hang the hooks of the front of the outer rail onto the slots on the front of

the rack. If necessary, use screws to secure the outer rails to the rack, as

illustrated above.

4. Pull out the rear of the outer rail, adjusting the length until it ts within the

posts of the rack.

5. Hang the hooks of the rear portion of the outer rail onto the slots on the rear

of the rack. If necessary, use screws to secure the rear of the outer rail to the

rear of the rack.

6. Repeat steps 1-5 for the remaining outer rail.

Slide rail mounted equipment is not to be used as a shelf or a work space.

Stability hazard. The rack stabilizing mechanism must be in place, or the

rack must be bolted to the oor before you slide the unit out for servicing.

Failure to stabilize the rack can cause the rack to tip over.

Chapter 3: System Interface

3-1

Chapter 3

System Interface

3-1 Overview

There are several LEDs on the control panel and on the drive carriers to keep you

constantly informed of the overall status of the system. SC217HQ+ models include

four front panels on the handles of the chassis which control each of the systems.

This chapter explains the meanings of all LED indicators and the appropriate

response you may need to take.

Figure 3-1. Control Panel

SUPERSERVER 2028TP-HTR/HC0R/HC1R-SIOM USER'S MANUAL

3-2

3-2 Control Panel Button

Alert

This LED is illuminated when an alert condition occurs.

• A solid red light indicates an overheat condition in the system.

• A ashing red light which ashes in one second intervals indicates a fan failure.

Power

The main power button on each of the four control panels is used to apply or remove

power from the power supply to each of the four systems in the chassis. Turning

power to the system off with this button removes the main power, but keeps standby

power supplied to the system. Therefore, you must unplug the AC power cord from

any external power source before servicing. The power button has a built-in LED

which will turn green when the power is on.

UID

When used with a UID compatible serverboard, the UID button is used to turn on

or off the blue light function of the LED. This is built into the front side of the UID

button and at the rear end of each serverboard node, for those serverboards which

support it. Once the blue light is activated, the unit can be easily located in very

large racks and server banks.

3-3 Control Panel LEDs

The four control panels are located on the front handle of the SC217HQ+ chassis.

Each control panel has two additional LEDs. These LEDs provide you with critical

information related to different parts of the system. This section explains what each

LED indicates when illuminated and any corrective action you may need to take.

SUPERSERVER 2028TP-HTR/HC0R/HC1R-SIOM USER'S MANUAL

3-4

Notes

4-1

Chapter 4: Warning Statements for AC Systems

Chapter 4

Standardized Warning Statements for AC Systems

4-1 About Standardized Warning Statements

The following statements are industry standard warnings, provided to warn the user

of situations which have the potential for bodily injury. Should you have questions

or experience difficulty, contact Supermicro's Technical Support department

for assistance. Only certied technicians should attempt to install or congure

components.

Read this appendix in its entirety before installing or conguring components in the

Supermicro chassis.

These warnings may also be found on our web site at http://www.supermicro.com/

about/policies/safety_information.cfm.

Warning!

This warning symbol means danger. You are in a situation that could cause bodily

injury. Before you work on any equipment, be aware of the hazards involved with

electrical circuitry and be familiar with standard practices for preventing accidents.

Warning Denition

警告の定義

この警告サインは危険を意味します。

人身事故につながる可能性がありますので、いずれの機器でも動作させる前に、

電気回路に含まれる危険性に注意して、標準的な事故防止策に精通して下さい。

此警告符号代表危险。

您正处于可能受到严重伤害的工作环境中。在您使用设备开始工作之前，必须充分意

识到触电的危险，并熟练掌握防止事故发生的标准工作程序。请根据每项警告结尾的

声明号码找到此设备的安全性警告说明的翻译文本。

此警告符號代表危險。

您目前所處的工作環境可能讓您受傷。您使用任何設備之前，請注意觸電的危險，

並且要熟悉預防事故發生的標準工作程序。請依照每一注意事項後的號碼找到相關

的翻譯說明內容。

4-3

Chapter 4: Warning Statements for AC Systems

안전을 위한 주의사항

경고!

이 경고 기호는 위험이 있음을 알려 줍니다. 작업자의 신체에 부상을 야기 할 수

있는 상태에 있게 됩니다. 모든 장비에 대한 작업을 수행하기 전에 전기회로와

관련된 위험요소들을 확인하시고 사전에 사고를 방지할 수 있도록 표준

작업절차를 준수해 주시기 바랍니다.

해당 번역문을 찾기 위해 각 경고의 마지막 부분에 제공된 경고문 번호를

참조하십시오

BELANGRIJKE VEILIGHEIDSINSTRUCTIES

Dit waarschuwings symbool betekent gevaar. U verkeert in een situatie die

lichamelijk letsel kan veroorzaken. Voordat u aan enige apparatuur gaat werken,

dient u zich bewust te zijn van de bij een elektrische installatie betrokken risico's

en dient u op de hoogte te zijn van de standaard procedures om ongelukken te

voorkomen. Gebruik de nummers aan het eind van elke waarschuwing om deze te

herleiden naar de desbetreffende locatie.

BEWAAR DEZE INSTRUCTIES

.  !              

 

            

 

           

        

     

4-4

SUPERSERVER 2028TP-HTR/HC0R/HC1R-SIOM USER'S MANUAL

Installation Instructions

Warning!

Read the installation instructions before connecting the system to the power source.

Warnung

Vor dem Anschließen des Systems an die Stromquelle die Installationsanweisungen

lesen.

¡Advertencia!

Lea las instrucciones de instalación antes de conectar el sistema a la red de

alimentación.

Attention

Avant de brancher le système sur la source d'alimentation, consulter les directives

d'installation.

設置手順書

システムを電源に接続する前に、設置手順書をお読み下さい。

시스템을 전원에 연결하기 전에 설치 안내를 읽어주십시오.

Waarschuwing

Raadpleeg de installatie-instructies voordat u het systeem op de voedingsbron

aansluit.

警告

将此系统连接电源前,请先阅读安装说明。

警告

將系統與電源連接前，請先閱讀安裝說明。

.חתמ רוקמל תכרעמה רוביח ינפל הנקתה תוארוה תא אורקל שי

        

4-8

SUPERSERVER 2028TP-HTR/HC0R/HC1R-SIOM USER'S MANUAL

Equipment Installation

機器の設置

トレーニングを受け認定された人だけがこの装置の設置、交換、またはサービスを許可

されています。

Warning!

Only trained and qualied personnel should be allowed to install, replace, or service

this equipment.

Warnung

Das Installieren, Ersetzen oder Bedienen dieser Ausrüstung sollte nur geschultem,

qualiziertem Personal gestattet werden.

¡Advertencia!

Solamente el personal calicado debe instalar, reemplazar o utilizar este equipo.

Attention

Il est vivement recommandé de confier l'installation, le remplacement et la

maintenance de ces équipements à des personnels qualiés et expérimentés.

경고!

훈련을 받고 공인된 기술자만이 이 장비의 설치, 교체 또는 서비스를 수행할 수

있습니다.

警告

只有经过培训且具有资格的人员才能进行此设备的安装、更换和维修。

警告

只有經過受訓且具資格人員才可安裝、更換與維修此設備。

!הרהזא

.דויצה רובע תוריש תתל וא דויצה תא ףילחהל ,ןיקתהל יאשר דבלב ךמסומ תווצ

            

4-9

Chapter 4: Warning Statements for AC Systems

アクセス制限区域

このユニットは、アクセス制限区域に設置されることを想定しています。

アクセス制限区域は、特別なツール、鍵と錠前、その他のセキュリティの手段を用いての

み出入りが可能です。

Warning!

This unit is intended for installation in restricted access areas. A restricted access

area can be accessed only through the use of a special tool, lock and key, or other

means of security. (This warning does not apply to workstations).

Restricted Area

Waarschuwing

Deze apparatuur mag alleen worden geïnstalleerd, vervangen of hersteld door

geschoold en gekwaliceerd personeel.

Warnung

Diese Einheit ist zur Installation in Bereichen mit beschränktem Zutritt vorgesehen.

Der Zutritt zu derartigen Bereichen ist nur mit einem Spezialwerkzeug, Schloss und

Schlüssel oder einer sonstigen Sicherheitsvorkehrung möglich.

¡Advertencia!

Esta unidad ha sido diseñada para instalación en áreas de acceso restringido.

Sólo puede obtenerse acceso a una de estas áreas mediante la utilización de una

herramienta especial, cerradura con llave u otro medio de seguridad.

Attention

Cet appareil doit être installée dans des zones d'accès réservés. L'accès à une

zone d'accès réservé n'est possible qu'en utilisant un outil spécial, un mécanisme

de verrouillage et une clé, ou tout autre moyen de sécurité.

警告

此部件应安装在限制进出的场所，限制进出的场所指只能通过使用特殊工具、锁和钥

匙或其它安全手段进出的场所。

警告

此裝置僅限安裝於進出管制區域，進出管制區域係指僅能以特殊工具、鎖頭及鑰匙或

其他安全方式才能進入的區域。

4-10

SUPERSERVER 2028TP-HTR/HC0R/HC1R-SIOM USER'S MANUAL

Battery Handling

Warning!

There is the danger of explosion if the battery is replaced incorrectly. Replace the

battery only with the same or equivalent type recommended by the manufacturer.

Dispose of used batteries according to the manufacturer's instructions

경고!

이 장치는 접근이 제한된 구역에 설치하도록 되어있습니다. 특수도구, 잠금 장치 및

키, 또는 기타 보안 수단을 통해서만 접근 제한 구역에 들어갈 수 있습니다.

Waarschuwing

Dit apparaat is bedoeld voor installatie in gebieden met een beperkte toegang.

Toegang tot dergelijke gebieden kunnen alleen verkregen worden door gebruik te

maken van speciaal gereedschap, slot en sleutel of andere veiligheidsmaatregelen.

電池の取り扱い

電池交換が正しく行われなかった場合、破裂の危険性があります。交換する電池はメー

カーが推奨する型、または同等のものを使用下さい。使用済電池は製造元の指示に従

って処分して下さい。

警告

电池更换不当会有爆炸危险。请只使用同类电池或制造商推荐的功能相当的电池更

换原有电池。请按制造商的说明处理废旧电池。

警告

電池更換不當會有爆炸危險。請使用製造商建議之相同或功能相當的電池更換原有

電池。請按照製造商的說明指示處理廢棄舊電池。

תלבגומ השיג םע רוזא

!הרהזא

תרזעב תנתינ השיגה .השיג תלבגה םהב שיש םירוזאב הדיחיה תא ןיקתהל שי

(.דכו לוענמ ,חתפמ( דבלב החטבא ילכ'

. 





4-13

Chapter 4: Warning Statements for AC Systems

Backplane Voltage

バックプレーンの電圧

システムの稼働中は危険な電圧または電力が、バックプレーン上にかかっています。

修理する際には注意ください。

警告

当系统正在进行时，背板上有很危险的电压或能量，进行维修时务必小心。

警告

當系統正在進行時，背板上有危險的電壓或能量，進行維修時務必小心。

Warnung

Wenn das System in Betrieb ist, treten auf der Rückwandplatine gefährliche

Spannungen oder Energien auf. Vorsicht bei der Wartung.

¡Advertencia!

Cuando el sistema está en funcionamiento, el voltaje del plano trasero es peligroso.

Tenga cuidado cuando lo revise.

Attention

Lorsque le système est en fonctionnement, des tensions électriques circulent sur

le fond de panier. Prendre des précautions lors de la maintenance.

Warning!

Hazardous voltage or energy is present on the backplane when the system is

operating. Use caution when servicing.

경고!

이 장치에는 한 개 이상의 전원 공급 단자가 연결되어 있을 수 있습니다. 이 장치에

전원을 차단하기 위해서는 모든 연결 단자를 제거해야만 합니다.

Waarschuwing

Deze eenheid kan meer dan één stroomtoevoeraansluiting bevatten. Alle

aansluitingen dienen verwijderd te worden om het apparaat stroomloos te maken.

.         

       

4-16

SUPERSERVER 2028TP-HTR/HC0R/HC1R-SIOM USER'S MANUAL

Waarschuwing

De uiteindelijke verwijdering van dit product dient te geschieden in overeenstemming

met alle nationale wetten en reglementen.

ファン・ホットスワップの警告

警告！回転部品に注意。運転中は回転部(羽根)に触れないでください。シャーシから冷

却ファン装置を取り外した際、ファンがまだ回転している可能性があります。ファンの開

口部に、指、ドライバー、およびその他のものを近づけないで下さい。

警告!

警告！危险的可移动性零件。请务必与转动的风扇叶片保持距离。当您从机架移除

风扇装置，风扇可能仍在转动。小心不要将手指、螺丝起子和其他物品太靠近风扇

警告

危險的可移動性零件。請務必與轉動的風扇葉片保持距離。當您從機架移除風扇裝

置，風扇可能仍在轉動。小心不要將手指、螺絲起子和其他物品太靠近風扇。

경고!

이 제품은 해당 국가의 관련 법규 및 규정에 따라 폐기되어야 합니다.

Hot Swap Fan Warning

Warning!

Hazardous moving parts. Keep away from moving fan blades. The fans might still

be turning when you remove the fan assembly from the chassis. Keep ngers,

screwdrivers, and other objects away from the openings in the fan assembly's

housing.

Attention

La mise au rebut ou le recyclage de ce produit sont généralement soumis à des

lois et/ou directives de respect de l'environnement. Renseignez-vous auprès de

l'organisme compétent.

רצומה קוליס

!הרהזא

.הנידמה יקוחו תויחנהל םאתהב תויהל בייח הז רצומ לש יפוס קוליס

             

4-19

Chapter 4: Warning Statements for AC Systems

¡Advertencia!

Cuando instale el producto, utilice la conexión provista o designada o procure

cables, Cables de alimentación y adaptadores de CA que cumplan con los códigos

locales y los requisitos de seguridad, incluyendo el tamaño adecuado del cable y el

enchufe. El uso de otros cables y adaptadores podría causar un mal funcionamiento

o un incendio. La Ley de Seguridad de Aparatos Eléctricos y de Materiales prohíbe

El uso de cables certicados por UL o CSA (que tienen el certicado UL / CSA en

el código) para cualquier otros dispositivos eléctricos que los productos designados

únicamente por Supermicro.Attention

Attention

Lors de l'installation du produit, utilisez les cables de connection fournis ou désigné

ou achetez des cables, cables de puissance et adaptateurs respectant les normes

locales et les conditions de securite y compris les tailles de cables et les prises

electriques appropries. L'utilisation d'autres cables et adaptateurs peut provoquer

un dysfonctionnement ou un incendie. Appareils électroménagers et la Loi sur la

Sécurité Matériel interdit l'utilisation de câbles certies- UL ou CSA (qui ont UL ou

CSA indiqué sur le code) pour tous les autres appareils électriques sauf les produits

désignés par Supermicro seulement.

ימאתמו םיילמשח םילבכ AC

הרהזא!

םימאתמו םיקפס ,םילבכב שמתשהל שי ,רצומה תא םיניקתמ רשאכ AC וא ושכרנ רשא

הנוכנ הדימ ללוכ ,תוימוקמה תוחיטבה תושירדל ומאתוה רשאו ,הנקתהה ךרוצל ומאתוה

רצק וא הלקתל םורגל לולע ,רחא גוסמ םאתמ וא לבכ לכב שומיש . עקתהו לבכה לש

שמתשהל רוסיא םייק ,תוחיטבה יקוחו למשחה ירישכמב שומישה יקוחל םאתהב .ילמשח

ב םיכמסומה םילבכב- UL ב וא-CSA (לש דוק םהילע עיפומ רשאכ (UL/CSA רובע

י"ע םאתוה רשא רצומב קר אלא ,רחא ילמשח רצומ לכ Supermicro דבלב.

               

  .             

       .        

              UL CSA  (UL/CSA)

   Supermicro.

Specyfikacje produktu

Marka:	Supermicro
Kategoria:	serwer
Model:	SuperServer 2028TP-HC1R-SIOM
Kolor produktu:	Czarny
Wbudowany wyłącznik:	Tak
Wysokość produktu:	88 mm
Szerokość produktu:	438 mm
Głębokość produktu:	730 mm
Waga produktu:	32700 g
Certyfikat środowiskowy (zrównoważonego rozwoju):	RoHS
Certyfikaty:	UL/cUL/CB/BSMI/CE/CCC
Zakres temperatur (eksploatacja):	10 - 35 °C
Zakres wilgotności względnej:	8 - 90 %
Typ procesora:	Intel
Diody LED:	HDD, Network, Power
Zakres temperatur (przechowywanie):	-40 - 70 °C
Dopuszczalna wilgotność względna:	5 - 95 %
Ilość obsługiwanych rozmiarów dysków pamięci:	6
Obsługiwane rozmiary dysków pamięci:	2.5 "
Ilość portów USB 3.2 Gen 1 (3.1 Gen 1) Typu-A:	2
Obudowa:	Rack (2U)
Liczba wentylatorów:	4 went.
Obsługiwane rodzaje pamięci:	DDR4-SDRAM
Maksymalna pojemność pamięci:	2000 GB
Gniazdo procesora:	LGA 2011 (Socket R)
Procesor:	Intel® Xeon®
Układ płyty głównej:	Intel® C612
Poziomy raid:	0, 1,5, 6,10, 50, 60
Typ BIOS:	EEPROM
Zasilanie:	2000 W
Gniazda PCI Express x16 (Gen 3.x):	1
Wspierane interfejsy dysków twardych:	Serial Attached SCSI (SAS)-3
Liczba portów VGA (D-Sub):	1
Korekcja ECC:	Tak
Rozmiar pamięci BIOS:	128 Mbit
Wersja ACPI:	2.0
Wskaźnik magistrali systemowej:	9.6 GT/s
Model karty graficznej on-board:	Aspeed AST2400
Obsługa zasilania zapasowego (RPS):	Tak
Szeregowe porty komunikacyjne:	1
Gniazda PCI Express x8 (Gen 3.x):	1
Napięcie pamięci:	1.2 V
Intel® Xeon series:	E5-2600
Ilość slotów DIMM:	16
Liczba obsługiwanych procesorów:	2
Prędkość zegara pamięci RDIMM:	1600,1866,2133,2400 MHz
Przemieszczanie twardej wnęki na napęd HDD:	Tak
Ilość zainstalowanych, nadmiarowych źródeł zasilania:	2
Średnica czaszy wentylatora:	80 mm
Magistrala pamięci:	72 bit
Maksymalna pojemność pamięci RDIMM:	512 GB
Obsługuje rozmiary DIMM:	4GB, 8GB, 16GB, 32GB, 64GB
Port IPMI LAN (RJ-45):	Tak
Maksymalna pamięć podręczna:	55 MB
Typ magistrali systemowej:	QuickPath Interconnect (QPI)
Liczba portów SAS:	6
Funkcje BIOS:	APM 1.2, PCI 2.2, SMBIOS 2.3, UEFI