Instrukcja obsługi Supermicro SuperServer 1028UX-LL1-B8

Supermicro serwer SuperServer 1028UX-LL1-B8

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Supermicro SuperServer 1028UX-LL1-B8 (128 stron) w kategorii serwer. Ta instrukcja była pomocna dla 4 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/128

USER’S MANUAL

1.0a

SUPERSERVER®

1028UX-LL1-B8

1028UX-LL2-B8

1028UX-LL3-B8

The information in this User’s Manual has been carefully reviewed and is believed to be accurate.

The vendor assumes no responsibility for any inaccuracies that may be contained in this document,

makes no commitment to update or to keep current the information in this manual, or to notify any

person or organization of the updates. Please Note: For the most up-to-date version of this

manual, please see our web site at www.supermicro.com.

Super Micro Computer, Inc. ("Supermicro") reserves the right to make changes to the product

described in this manual at any time and without notice. This product, including software and

documentation, is the property of Supermicro and/or its licensors, and is supplied only under a

license. Any use or reproduction of this product is not allowed, except as expressly permitted by

the terms of said license.

IN NO EVENT WILL SUPERMICRO BE LIABLE FOR DIRECT, INDIRECT, SPECIAL, INCIDENTAL,

SPECULATIVE OR CONSEQUENTIAL DAMAGES ARISING FROM THE USE OR INABILITY TO

USE THIS PRODUCT OR DOCUMENTATION, EVEN IF ADVISED OF THE POSSIBILITY OF

SUCH DAMAGES. IN PARTICULAR, SUPERMICRO SHALL NOT HAVE LIABILITY FOR ANY

HARDWARE, SOFTWARE, OR DATA STORED OR USED WITH THE PRODUCT, INCLUDING THE

COSTS OF REPAIRING, REPLACING, INTEGRATING, INSTALLING OR RECOVERING SUCH

HARDWARE, SOFTWARE, OR DATA.

Any disputes arising between manufacturer and customer shall be governed by the laws of Santa

Clara County in the State of California, USA. The State of California, County of Santa Clara shall

be the exclusive venue for the resolution of any such disputes. Super Micro's total liability for all

claims will not exceed the price paid for the hardware product.

FCC Statement: This equipment has been tested and found to comply with the limits for a Class

A digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference when the equipment is operated in a commercial

environment. This equipment generates, uses, and can radiate radio frequency energy and, if not

installed and used in accordance with the manufacturer’s instruction manual, may cause harmful

interference with radio communications. Operation of this equipment in a residential area is likely

to cause harmful interference, in which case you will be required to correct the interference at your

own expense.

California Best Management Practices Regulations for Perchlorate Materials: This Perchlorate

warning applies only to products containing CR (Manganese Dioxide) Lithium coin cells. “Perchlorate

Material-special handling may apply. See www.dtsc.ca.gov/hazardouswaste/perchlorate”

WARNING: Handling of lead solder materials used in this

product may expose you to lead, a chemical known to

the State of California to cause birth defects and other

reproductive harm.

Manual Revision 1.0a

Release Date: July 21, 2017

Unless you request and receive written permission from Super Micro Computer, Inc., you may not

copy any part of this document.

Information in this document is subject to change without notice. Other products and companies

referred to herein are trademarks or registered trademarks of their respective companies or mark

holders.

Printed in the United States of America

iii

Preface

About This Manual

This manual is written for professional system integrators and PC technicians.

It provides information for the installation and use of the SuperServer

1028UX-LL1-B8/1028UX-LL2-B8/1028UX-LL3-B8. Installation and maintenance

should be performed by experienced technicians only.

Manual Organization

Chapter 1: Introduction

The rst chapter provides a checklist of the main components included with the

server system and describes the main features of the X10DRU-XLL serverboard

and the SC119UTS-R751P-T chassis.

Chapter 2: Server Installation

This chapter describes the steps necessary to install the SuperServer

1028UX-LL1-B8/1028UX-LL2-B8/1028UX-LL3-B8 into a rack and check out the

server conguration prior to powering up the system. If your server was ordered

without processor and memory components, this chapter will refer you to the

appropriate sections of the manual for their installation.

Chapter 3: System Interface

Refer here for details on the system interface, which includes the functions and

information provided by the control panel on the chassis as well as other LEDs

located throughout the system.

Chapter 4: Standardized Safety Warnings

You should thoroughly familiarize yourself with this chapter for a general overview

of safety precautions that should be followed when installing and servicing the

SuperServer 1028UX-LL1-B8/1028UX-LL2-B8/1028UX-LL3-B8.

Chapter 5: Advanced Serverboard Setup

Chapter 5 provides detailed information on the X10DRU-XLL serverboard,

including the locations and functions of connections, headers and jumpers. Refer

to this chapter when adding or removing processors or main memory and when

reconguring the serverboard.

Table of Contents

Chapter 1 Introduction

1-1 Overview ......................................................................................................... 1-1

1-2 Serverboard Features ..................................................................................... 1-2

Processors 1-2 .....................................................................................................

Memory 1-2 ...........................................................................................................

SAS 1-2 .................................................................................................................

SATA ................................................................................................................ 1-2

Input/Output 1-2 .....................................................................................................

1-3 Server Chassis Features ................................................................................ 1-3

System Power ................................................................................................. 1-3

Hard Drives ..................................................................................................... 1-3

PCI Expansion Slots ....................................................................................... 1-3

Front Control Panel ......................................................................................... 1-3

Cooling System ............................................................................................... 1-3

1-4 Contacting Supermicro .................................................................................... 1-5

Chapter 2 Server Installation

2-1 Overview ......................................................................................................... 2-1

2-2 Unpacking the System .................................................................................... 2-1

2-3 Preparing for Setup ......................................................................................... 2-1

Choosing a Setup Location ............................................................................. 2-1

2-4 Warnings and Precautions .............................................................................. 2-2

Rack Precautions ............................................................................................ 2-2

Server Precautions .......................................................................................... 2-2

Rack Mounting Considerations ....................................................................... 2-3

Ambient Operating Temperature ................................................................ 2-3

Reduced Airow ......................................................................................... 2-3

Mechanical Loading ................................................................................... 2-3

Circuit Overloading ..................................................................................... 2-3

Reliable Ground ......................................................................................... 2-3

2-5 Installing the System into a Rack ................................................................... 2-4

Identifying the Sections of the Rack Rails ...................................................... 2-4

Installing the Optional Inner Rail Extensions .................................................. 2-5

Assembling the Outer Rails ............................................................................ 2-6

Installing the Outer Rails onto the Rack ......................................................... 2-7

Installing and Removing the Chassis From a Rack ....................................... 2-8

Installing the Server into a Telco Rack ........................................................... 2-9

SUPERSERVER 1028UX-LL1-B8/LL2-B8/LL3-B8 User's Manual

Chapter 1

Introduction

1-1 Overview

The SuperServer 1028UX-LL1-B8/1028UX-LL2-B8/1028UX-LL3-B8 is a high-end

server comprised of two main subsystems: the SC119UTS-R751P-T 1U server

chassis and the X10DRU-XLL dual processor serverboard. Please refer to our

website for information on operating systems that have been certied for use with

the system (www.supermicro.com).

In addition to the serverboard and chassis, various hardware components have

been included:

• Eight sets of 4-cm counter-rotating fans (LL1/LL2: FAN-0101L4, LL3: FAN-

0141L4))

• Two passive CPU heatsinks (SNK-P0057PU)

• Two air shrouds, one for each CPU (MCP-310-81907-0N)

• Add-on/Riser Cards

One AOC-UR-I4G Ultra riser card

One AOC-S3108L-H8IR-16DD riser card

One RSC-R1UW-2E16 riser card

One RSC-R1UW-E8R riser card

• SAS Accessories

One SAS backplane (BPN-SAS3-116A-N2)

Ten drive carriers (MCP-220-00047-0B)

• One rail kit consisting of one set each of outer rails (MCP-290-00102-0N),

inner rails (MCP-290-00120-0N) and inner rail extensions (MCP-290-00112-

0N)

Note: For your system to work properly, please follow the links below to download

all necessary drivers/utilities and the user’s manual for your server.

• Product manuals: http://www.supermicro.com/support/manuals/

• Product drivers and utilities: ftp://ftp.supermicro.com

• Product safety info: http://www.supermicro.com/about/policies/safety_

information.cfm

Chapter 1: Introduction

1-1

1-2

SUPERSERVER 1028UX-LL1-B8/LL2-B8/LL3-B8 User's Manual

1-2 Serverboard Features

At the heart of the 1028UX-LL1-B8/1028UX-LL2-B8/1028UX-LL3-B8 lies the

X10DRU-XLL, a dual processor serverboard based on the Intel® PCH C612 Express

chipset. Below are the main features of the serverboard. (See Figure 1-1 for a block

diagram of the chipset.)

Processors

The server supports dual Intel processors in R3 LGA 2011 sockets. The 1028UX-

LL1-B8 includes two Xeon E5-2643 v4 processors, the 1028UX-LL2-B8 includes

two Xeon E5-2687W v4 processors and the 1028UX-LL3-B8 includes two Xeon

E5-2689 v4 processors.

Memory

The 1028UX-LL1-B8/1028UX-LL2-B8/1028UX-LL3-B8 features 16 DIMM slots. The

system comes with eight 8 GB preinstalled memory modules for a total of 64 GB

DDR4-2400 MHz low-prole registered ECC memory. Please refer to Chapter 5

for installing memory.

SAS

An onboard LSI 3108 controller on the X10DRU-XLL provides support for SAS 3.0

drives. These drives are RAID 0, 1, 5, 6 and 10 supported.

SATA

Ten SATA 3.0 ports supported by the Intel PCH are included on the serverboard.

RAID 0, 1, 5 and 10 is supported. Refer to the following FTP site for setup guidelines:

ftp://ftp.supermicro.com/driver/SAS/LSI/LSI_SAS_EmbMRAID_SWUG.pdf.

Input/Output

The rear I/O includes a VGA port, a COM port, two USB 3.0 ports, quad Gb LAN

ports and one dedicated IPMI LAN port.

1-3

Chapter 1: Introduction

1-3 Server Chassis Features

The 1028UX-LL1-B8/1028UX-LL2-B8/1028UX-LL3-B8 is built upon the

SC119UTS-R751P-T chassis. The following is a general outline of the main features

of the chassis.

System Power

The chassis features a redundant 750W power supply consisting of two redundant,

hot-plug power modules, so one may be replaced without powering down the

system.

Hard Drives

The default chassis supports ten hot-swap 2.5" drives bays, which consist of eight

SAS 3.0 drives and two SATA 3.0 drives.

PCI Expansion Slots

Riser cards and brackets are required to install expansion cards. The system has

two pre-installed riser cards to support three PCI expansion cards as follows. The

RSC-R1UW-2E16 riser for two PCI-E 3.0 x16 add-on cards and the RSC-R1UW-

E8R riser for one PCI-E 3.0 x8 add-on card.

Front Control Panel

The chassis front control panel provides system monitoring lights and power control

buttons. See Chapter 3 for details.

Cooling System

The system has an innovative cooling design that features eight 4-cm counter-

rotating fans located in the middle section of the chassis. Fan speed may be

controlled by IPMI to respond to uctuations in system temperature.

1-4

SUPERSERVER 1028UX-LL1-B8/LL2-B8/LL3-B8 User's Manual

Figure 1-1. PCH C612 Express Chipset:

System Block Diagram

Note: This is a general block diagram. Please see Chapter 5 for details.

Port A Port B Port B NCSI Port C Port C

NIC

Port A

0~7

Port B

0~7

Port B

8~15

Port C

0~10

Port C

11~15

Port 0, 1 Port 3

Type ARear

#1 #1 #1 #1 #1 #1 #1 #1

#2 #2 #2 #2 #2 #2 #2 #2

#3 #3 #3 #3 #3 #3 #3 #3

DDR4 DIMM

x16

PE1 PE2 PE3 PE1 PE2 PE3 QPI1 QPI 0QPI1 QPI 0

DMI

Upper

Lower

Processor

VGA

DDR3 NCSI

LAN

UART

Onboard TPM (Optional)

2-2

SUPERSERVER 1028UX-LL1-B8/LL2-B8/LL3-B8 User's Manual

2-4 Warnings and Precautions

Rack Precautions

• Ensure that the leveling jacks on the bottom of the rack are fully extended to

the oor with the full weight of the rack resting on them.

• In single rack installation, stabilizers should be attached to the rack. In multiple

rack installations, the racks should be coupled together.

• Always make sure the rack is stable before extending a component from the

rack.

• You should extend only one component at a time - extending two or more

simultaneously may cause the rack to become unstable.

• Rack-mounted equipment should not be used as a shelf or work space.

Server Precautions

• Review the electrical and general safety precautions in Chapter 4.

• Determine the placement of each component in the rack you install the before

rails.

• Install the heaviest server components on the bottom of the rack rst, and then

work up.

• Use a regulating uninterruptible power supply (UPS) to protect the server from

power surges, voltage spikes and to keep your system operating in case of a

power failure.

• Allow the hot plug SATA drives and power supply modules to cool before

touching them.

• Always keep the rack's front door and all panels and components on the servers

closed when not servicing to maintain proper cooling.

Chapter 2: Server Installation

2-9

Installing the Server into a Telco Rack

Optional brackets are needed to install the server to a telco (open type) rack.

To install the server into a Telco type rack, use the two L-shaped brackets on either

side of the chassis (four total). First, determine how far follow the server will extend

out the front of the rack. Larger chassis should be positioned to balance the weight

between front and back. If a bezel is included on your server, remove it. Then

attach the two front brackets to each side of the chassis, then the two rear brackets

positioned with just enough space to accommodate the width of the telco rack.

Finish by sliding the chassis into the rack and tightening the brackets to the rack.

Figure 2-6. Installing the Server into a Telco Rack

Note: Figures are for illustrative purposes only. Servers should always be installed

into racks starting at the bottom.

2-10

SUPERSERVER 1028UX-LL1-B8/LL2-B8/LL3-B8 User's Manual

Notes

Chapter 3: System Interface

3-3

Power: Indicates power is being supplied to the system power supply units. This

LED should normally be illuminated when the system is operating.

HDD: Indicates activity on the hard drive when ashing.

Overheating

There are several possible responses if the system overheats.

Overheat Temperature Setting

Some backplanes allow the overheat temperature to be set at 45, 50, or 55 by

changing a jumper setting. For more information, consult the backplane user manual

at www.supermicro.com. (Click Support, then the Manuals link.)

Responses

If the server overheats:

1. Use the LEDs to determine the nature of the overheating condition.

2. Conrm that the chassis covers are installed properly.

3. Check the routing of the cables and make sure all fans are present and operating

normally.

4. Verify that the heatsinks are installed properly.

NIC: Indicates network activity on GLAN1 when ashing.

3-4

SUPERSERVER 1028UX-LL1-B8/LL2-B8/LL3-B8 User's Manual

3-4 Drive Carrier LEDs

The chassis includes externally accessible SATA drives. Each drive carrier displays

two status LEDs on the front of the carrier.

• Green: When illuminated, this LED indicates drive activity. It blinks on and off

when that particular drive is being accessed This function is controlled by the

backplane.

• Red: When illuminated, this LED indicates a drive failure. You should be notied

by your system management software.

3-5 Power Supply LEDs

On the rear of the power supply module, an LED displays the status.

• Solid Green: When illuminated, indicates that the power supply is on.

• Blinking Green: When blinking, indicates that the power supply is plugged in

and turned off by the system.

• Blinking Amber: When blinking, indicates that the power supply has a warning

condition and continues to operate.

• Solid Amber: When illuminated, indicates that the power supply is plugged in

and in an abnormal state. The server system might need service. Please contact

Supermicro technical support.

4-4

SUPERSERVER 1028UX-LL1-B8/LL2-B8/LL3-B8 User's Manual

Installation Instructions

Warning!

Read the installation instructions before connecting the system to the power source.

Warnung

Vor dem Anschließen des Systems an die Stromquelle die Installationsanweisungen

lesen.

¡Advertencia!

Lea las instrucciones de instalación antes de conectar el sistema a la red de

alimentación.

Attention

Avant de brancher le système sur la source d'alimentation, consulter les directives

d'installation.

設置手順書

システムを電源に接続する前に、設置手順書をお読み下さい。

      .

Waarschuwing

Raadpleeg de installatie-instructies voordat u het systeem op de voedingsbron

aansluit.

警告

将此系统连接电源前,请先阅读安装说明。

警告

將系統與電源連接前，請先閱讀安裝說明。

.חתמ רוקמל תכרעמה רוביח ינפל הנקתה תוארוה תא אורקל

        

Specyfikacje produktu

Marka:	Supermicro
Kategoria:	serwer
Model:	SuperServer 1028UX-LL1-B8
Kolor produktu:	Czarny
Wbudowany wyłącznik:	Tak
Częstotliwość wejściowa AC:	50 - 60 Hz
Napięcie wejściowe AC:	100 - 240 V
Wysokość produktu:	178 mm
Szerokość produktu:	437 mm
Głębokość produktu:	889 mm
Waga produktu:	30400 g
Certyfikat środowiskowy (zrównoważonego rozwoju):	RoHS
Procesor wbudowany:	Nie
Prędkość transferu danych przez Ethernet LAN:	10,100,1000 Mbit/s
Ilość portów Ethernet LAN (RJ-45):	4
Zakres temperatur (eksploatacja):	10 - 35 °C
Zakres wilgotności względnej:	8 - 90 %
Liczba portów USB 2.0:	9
Przewodowa sieć LAN:	Tak
Waga wraz z opakowaniem:	47200 g
Zakres temperatur (przechowywanie):	-40 - 70 °C
Dopuszczalna wilgotność względna:	5 - 95 %
Ilość obsługiwanych rozmiarów dysków pamięci:	72
Obsługiwane rozmiary dysków pamięci:	3.5 "
Obudowa:	Rack (1U)
Liczba wentylatorów:	7 went.
Obsługiwane rodzaje pamięci:	DDR3-SDRAM
Maksymalna pojemność pamięci:	1000 GB
Gniazdo procesora:	LGA 2011 (Socket R)
Procesor:	Intel® Xeon®
Układ płyty głównej:	Intel® C612
Poziomy raid:	0, 1,5, 10
Typ BIOS:	AMI
Ilość złączy SATA III:	2
Zasilanie:	2000 W
Wspierane interfejsy dysków twardych:	Serial Attached SCSI (SAS)-2, Serial ATA III
Rodzaj interfejsu sieci Ethernet:	Fast Ethernet, Gigabit Ethernet
Liczba portów VGA (D-Sub):	1
Obsługa funkcji Plug & Play:	Tak
Korekcja ECC:	Tak
Rozmiar pamięci BIOS:	16 Mbit
Wersja systemu BIOS (SMBIOS):	2.3
Technologia okablowania Copper Ethernet:	10GBASE-T, 100BASE-TX, 1000BASE-T
Wskaźnik magistrali systemowej:	8 GT/s
Wersja gniazd typu Slot (PCI Express):	3.0
Wsparcie wentylatorów nadmiarowych:	Tak
Rodzaj pamięci:	240-pin DIMM
Napięcie pamięci:	1.35, 1.5 V
Ilość slotów DIMM:	16
Liczba obsługiwanych procesorów:	2
Prędkość zegara pamięci RDIMM:	800,1066,1333,1600,1866 MHz
Przemieszczanie twardej wnęki na napęd HDD:	Tak
Ilość zainstalowanych, nadmiarowych źródeł zasilania:	1
Średnica czaszy wentylatora:	90 mm
Ilość złączy SATA II:	4
Maksymalna pojemność pamięci RDIMM:	512 GB
Maksymalna pojemność pamięci UDIMM:	128 GB
Prędkość zegara pamięci UDIMM:	800,1066,1333,1600,1866 MHz
Obsługuje rozmiary DIMM:	1GB, 2GB, 4GB, 8GB, 16GB, 32GB
PCI Express x8 slots:	4
Prąd stały (+5 V):	4 A
Port IPMI LAN (RJ-45):	Tak
Maksymalna pamięć podręczna:	30 MB
Typ magistrali systemowej:	QuickPath Interconnect (QPI)
Liczba portów SAS:	8
Funkcje BIOS:	APM 1.2, PCI 2.2, Plug & Play, SMBIOS 2.3, UEFI