Instrukcja obsługi Sunding SD-581C

Sunding Nie skategoryzowane SD-581C

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Sunding SD-581C (2 stron) w kategorii Nie skategoryzowane. Ta instrukcja była pomocna dla 2 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/2
CLK Mode(12H/24H)
Computer Battery Installation
While the default Maintenance Alert digit
200 RIGHTkm/m is flashing, Press the button
to choose km/m. Press the 200/400/600/800 LEFT
button to confirm and enter into mode. BASIC ALL Or select
(when the the Maintenance Alert digit you set, the ODO
will appear on the screen to alert the rider, press the RIGHT
button seconds to cancel it.)3
24 Function Instruction Manual V0.1
Remove the battery cover from the bottom of the computer by using a
flat blade screwdriver, install battery with the positive (+) pole facing the
battery cover and replace the cover. Should the LCD show irregular
figures, take out the battery and reinstall it.
Attach the mounting shoe with the cable ties
to the handlebars as shown in the diagram.
Attach the computer to the mounting shoe
by sliding the unit until it snaps firmly into
position. To remove, press down on the
release catch, and remove the computer. To
check for proper speed function and sensor
alignment, spin the front wheel with the
computer in speed mode. Adjust the position
of sensor and magnet if there is on or weak
signal.
Computer
Long press + button for 3 seconds to enter setting modeLEFT RIGHT .
‘ ’ appears on the screed when the battery has been installed, with 2060
one figure flashing enter the wheel circumference using the formula
below.
In the example above you would enter . Press the button to 2198 RIGHT
advance the digits as needed and the button to confirm and LEFT
advance. (The circumference ranges 0mm~9999mm), press the LEFT
button to enter mode.KM/M
Setting(km/h)/(m/h)
Press the button to choose or .RIGHT km/h m/h
Press the button to enter mode.LEFT CLOCK
Setting Maintenance alert
In CLOCK Mode, press the button for seconds LEFT 3
to enter 12/24H selection. Press once more to swap
between 12/24 hours. Press the RIGHT button to enter
the Hour mode, when the figure indicating HOUR starts
to flash, press the LEFT button to adjust it. Continue to
press the RIGHT button to enter the Minute mode, when the figure
indicating MINUTE starts to flash, press the LEFT button to adjust. Press
the RIGHT button to confirm & press the RIGHT button again to switch to
ODO mode.
SD-581C Bicycle Computer
Installation of Speedometer
Attach speedometer sensor to the front fork using the ties. The
computer and sensor should be installed on the same side of the
fork, with distance between them of less than 60cm. The arrow
on the sensor should point at the magnet. Install magnet as
shown in figure. Distance between sensor and magnet should
be 3.0mm.
NOOFF
-SPD Current Speed
- ODO Odometer (0~99999km/m)
- DST Trip Distance
- MXS Maximum Speed
-AVS Average Speed
- TM Elapsed Time
- CLK Clock (12H/24H)
- TMP Temperature / (-10°C~70°C)
- MIN TMP Minimum Temperature
- MAX TMP Maximum Temperature
-CAL Calories Expended
- FAT Fat Burned
-SCAN
- “+”“-”Comparator
- SETTING SPEED SCALE (km/h,m/h)
- SETTING TYRE CIRCUMFERENCE / (0mm~9999mm)
- SETTING THE LAST VALUE OF ODOMETER / ODO
- MAINTENANCE ALERT
-FREEZE FRAME MEMORY
-LOW BATTERY INDICATOR
-BASIC OR ALL
-SMART BACKLIGHT
-BACKLIGHT IS LONG BRIGHT
- AUTO ON/OFF
Setting Rider’s Weight
The default weight is 65kg, press the button to adjust the RIGHT
flashing weight number according to rider’s weight, press buttonLEFT
to confirm and advance. Weight ranges : 20~150kg. Press the LEFT
button to enter into Maintenance Alert setting.
Computer
Sensor
Magnet
Notice
Pass bicycle spokes through the
plastic hole on the bottom of the
magnet and tighten to secure
The magnet is designed for
spokes that are less than
2mm thick.
FUNCTIONS
Mounting Shoe
Installation
Parameter Settings
Wheel Size Input
3.0m m
BASIC Or ALL
Press the RIGHT button select BASIC OR ALL, Press the LEFT
button to confirm and enter into Clock mode. “BASIC” Indicates that the
menu displays basic functions except for MIN TMP \ MAX TMP\ and CAL
FAT.
“ALL” Indicates that the menu displays all functions including MIN TMP \
MAX TMP \ CAL FAT and .
In mode, press the button for seconds to set the ODO LEFT 2 ODO
value. The initial value is . when one figure 0000.0
flashes, press the button to adjust it, and the RIGHT
LEFT button to confirm and start to set the next figure.
NOTE: Before re-installing the battery, take a note of
your mileage and then re-enter the value once the
battery is replaced.
Setting the Last value of Odometer
Freeze Frame Memory
Sleep Mode
Average Speed (AVS)
Maximum Speed (MXS)
Speedometer
In mode, the total distance is indicated on-screen.ODO
The mileage range is ~ km(m). The display 0.001 99999
will return to when the value exceeds its maximum 0
limit, press the button to enter mode.RIGHT DST
Speed is shown at all times on-screen, its maximum reading is
99.9 0.1km/h(m/h), and is accurate to +/- km/h (m/h).
Speed Comparator
Odometer
Trip Distance (DST)
In mode, the distance for one trip is indicated DST
on the bottom line. ranges from km(m).DST 0~9999
When the value exceed the range limit, it resets to 0
automatically. Both the time and the distance records
will be cleared when the time of one trip exceed the range limits.
Press the button for seconds to clear the records of , ,LEFT 5 DST MXS
AVS TMand .
Press the button to enter mode.RIGHT MXS
In mode, maximum speed is indicated on the MXS
bottom line. Press the button for seconds to LEFT 5
clear the records of , , MXS DST AVS TM and .
In AVS mode, average speed is indicated on the
bottom line. Press the button for seconds to LEFT 5
clear the records of AVS DST MXS TM, , and .
Press the right button to enter mode.TM
Scan
In mode , , , SCAN DST MXS AVS TM and modes are
indicated in turn every seconds.4
Press the button to enter Mode.RIGHT CLOCK
If no signal has been received for seconds, the computer will enter 300
into Sleep Mode, the value remains stored. It will turn back to the CLK
previous mode with all the data collected when the signal is received
again or any button is pressed.
Press the button at any time to enter into freeze frame memory LEFT
mode. Flashing data will appear on the screen. Press the TM RIGHT
button to view the records of , , DST MXS AVS TM. and
Malfunction
Problems
No speedometer
Incorrect magnet / sensor alignment.
Inaccurate value is
indicated
Improper input, such as wheel
circumference.
Slow display response
Temperature exceeds operating limits
(0°C~55°C).
Black display
Temperature too high, or placed in
direct sunlight for too long. Let the unit
cool down.
Weak display
Poor battery contact or dead battery.
Display shows irregular
figures
Take out battery and re-install after 10
seconds.
Backlight long Bright
Backlight long Bright is off by default. In clock mode press and
hold the mode key for 5 seconds to turn on Backlight long
Bright. Press and hold the mode key for 5 seconds and the
Backlight long Bright will turn off. After the computer enters the
sleep mode the Backlight long Bright is turned off.
The Smart Backlight will activate when there is insufficient light.
Press any button to turn on the Backlight for seconds.5
Smart Backlight
If the voltage remaining is less than 2.7V, the Low Battery
Indicator will flash as a reminder to change the battery.
Low Battery Indicator
Displays the current temperature, ranging from °C to °C.-10 70
Temperature (TMP)
Maximum Temperature (MAX TMP)
Displays the maximum temperature of a single trip.
Displays the minimum temperature of a single trip.
Minimum Temperature (MIN TMP)
For total heat consumed from last reset of code table to the current
driving process, the counting range is kcal.0~9999
For total fat from last reset of code table to the current driving
process, the counting range is kg .0~9999.9
Calories Expended (CAL)
Fat Burned (FAT)
Function Descriptions
Parameter Settings
Malfunctions and Problems
Accessories
Sensor
Mounting Shoe
Cable Ties
Wheel Magnet
CR2032 Battery
Trip Time
In mode, trip time is indicated on the bottom line.TM
TM ranges from to , and will be reset 0:00:00 9:59:59
to when the value exceed the limit. Press the 0 LEFT
button for seconds to clear the records of , ,5 TM DST
and MXS AVS RIGHT. Press the button to enter
Temperature mode(TMP).
During riding, ‘ ’ and ‘ ’ indicates the current speed is higher or
lower than the average speed (AVS).
In DST\ MXS\ AVS\ TM\ MIN TMP MAX TMP mode, hold \ LEFT
button 3 seconds DST\ MXS\ AVS\ TM\ MIN TMP MAX TMP to \
clear all data.
In the fat/calorie mode, press and hold the button for 3LEFT
seconds: fat and calorie data are cleared
Clear All Data
Calorie / Fat Reset
Temperature Unit (C/F°) Setting
In Temperature Setting mode, hold button for seconds to 3LEFT
toggle between Celsius and Fahrenheit.

Specyfikacje produktu

Marka: Sunding
Kategoria: Nie skategoryzowane
Model: SD-581C

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Sunding SD-581C, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje Nie skategoryzowane Sunding

Sunding

Sunding SD-536B Instrukcja

31 Stycznia 2025
Sunding

Sunding SD-589 Instrukcja

31 Stycznia 2025
Sunding

Sunding JOY-651 Instrukcja

31 Stycznia 2025
Sunding

Sunding SD-581C Instrukcja

31 Stycznia 2025

Instrukcje Nie skategoryzowane

Najnowsze instrukcje dla Nie skategoryzowane

AirLive

AirLive POE-GSH402-BT Instrukcja

25 Marca 2025
ETON

ETON UG VW T5 F3.2 Instrukcja

25 Marca 2025
Ikan

Ikan PT4500S-TMW Instrukcja

25 Marca 2025
WEG

WEG MPW18-3-D004 Instrukcja

25 Marca 2025
Vello

Vello HGS-2 Instrukcja

24 Marca 2025
Genexis

Genexis FiberBox XGS2120 Instrukcja

24 Marca 2025
Autel

Autel MaxiSys Ultra S2 Instrukcja

24 Marca 2025
Thermador

Thermador VTN2DA Instrukcja

24 Marca 2025
Kanto

Kanto CM-EXT60 Instrukcja

24 Marca 2025
Silver Cross

Silver Cross Geneva Wardrobe Instrukcja

24 Marca 2025