Instrukcja obsługi SunBriteTV SB-WM-ART2-XL-BL
SunBriteTV
wspornik ścienny
SB-WM-ART2-XL-BL
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla SunBriteTV SB-WM-ART2-XL-BL (8 stron) w kategorii wspornik ścienny. Ta instrukcja była pomocna dla 6 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek
Strona 1/8
SB-WM-ART2-L-BL
SB-WM-ART2-XL-BL
Weatherproof Universal -Arm Articulating MountDual
for Large TVs
INSTALLATION MANUAL
2
WARNING
The maximum weight of this wall mount is 150 lbs (68.04 kg). Use with heavier than
the maximum weight indicated may result in instability causing possible injury.
Ensure these instructions are thoroughly understood before attempting installation. If unsure of any part of the installation
process, contact a professional installer for assistance.
The wall or mounting surface must be capable of supporting the combined weight of the mount and the TV; otherwise the
structure must be reinforced. Installer is responsible for verifying the wall/mounting surface and the anchors used can support
the total load of the installation.
Safety gear and proper tools must be used. Failure to do so can result in property damage and/or serious injury.
A minimum of two people is required for this installation and it is highly recommended that this product be installed by qualied
professionals.
Follow all instructions and recommendations regarding suitable locations for TV installation. Consult the TV equipment’s
documentation for information relative to its requirements.
NOTE: This mount supports TV mounting from VESA 200x100, 200x200, up to 600x400.
SPECIFICATIONS BOX CONTENTS TOOLS REQUIRED
• Wall Arm Assembly (1) • Power Drill
• •Adapter Bracket (2) 1/4" & 5/16" Drill Bits
• • LevelAdapter Plate (1)
• SunBrite Adapter Bars (4) 1/2" (13mm) Wrench•
• • HammerCable Covers (6)
• •Hardware Kit (1) Stud Finder
• Maximum Load: 150 lbs (68.04 k g)
• Maximum Extension: 30-5/8"
• Wire Management
• Pan/Swivel Range: 180°
• Tilt Range: -5° /+ 15°
•Weather Resistant Coating
• Stainless Steel Mounting Hardware • Template (1) Phillips Screw Driver•
HARDWARE
IMAGE DESCRIPTION ITEM QUANTITY
BAG 1
Phillips Head Bolt
(A) M4x10 (B) M4x20 (C) M4x30 (D) M4x40
(E) M5x10 (F) M5x20 (G) M5x30 (H) M5x40
(I) M6x10 (J) M6x20 (K) M6x30 (L) M6x40
(M) M8x10 (N) M8x20 (O) M8x30 (P) M8x40
4 of each size
Flat Washer (Q) M5
(R) M8
16
8
Nylon Spacer (S) M4/M5
(T) M6/M8
8
8
Square Washer (U) 36.2x2.5mm 4
Recessed Hole Spacer (V) Recessed Hole Spacer 4
Spacer (W) Spacer 4
BAG 2
Lag Bolt (X) M8x65 Bolt 6
Anchor 6(Y) Concrete Anchor
Lag Bolt Washer (Z) Flat Washer 6
Phillips Head Flange Bolt (AA) M6x12 4
Button Head Flange Bolt (BB) M8x12 4
Hex Key — 1
Security bit — 4
3
INSTALLATION
Layout and Drilling
1. Determine general location of the TV.
2. Use a stud nder to nd the nearest wall studs if applicable and mark their location.
3. Tape template at and level to wall surface, aligning the template’s slots with the stud markings on the wall.
NOTE: Use of a bead level is recommended.
NOTE: Template corners fold up to catch debris.
4. Use a pen or pointed object to mark bore locations.
ATTENTION: Before drilling, verify there is a minimum of 1-3/8" of concrete thickness to be used for the
concrete anchors. Ensure to mount in a solid part of the block, generally 1" minimum from
the side of the block. Cinder block must meet ASTM C-90 specifications.
ATTENTION: Concrete must be 2000 psi density minimum. Lighter density concrete may not hold concrete
anchor.
ATTENTION: A standard electric drill on slow setting should be used to drill the holes instead of a hammer
drill to avoid breaking out the back of the hole when entering a void or cavity.
5. Drill holes :(Figure 1)
• Use 1/4" bit for drilling into wooden studs (x4).
• Use 5/16" bit for drilling into concrete wall (x6).
NOTE: Two additional holes and provided anchors are needed for concrete installs.
ATTENTION: Be sure to drill holes centered within studs. Do not drill into mortar joints.
Wall Mounting of Arm Assembly
1. Hammer concrete anchors (Y) into wall as applicable (Figure 1).
2. Apply washers (Z) to lag bolts (X).
3. Hold Arm Assembly in place while applying lag bolts (X) with washers (Z).
NOTE: A properly mounted Arm Assembly will be oriented so that its Keyed Notches side of the
Arm Assembly Head Mount is upward.
4. Tighten bolts snugly without overtightening.
CAUTION: Overtightening can damage the bolts and reduce their holding strength. Refer to the
mounting template for specics.
Figure 1
5/16" Holes for Concrete
1/4" Holes for Studs
Arm Assembly
Keyed
Notches
Head Mount
Concrete Anchors
(for concrete only)
Washers
Lag Bolts (X)
Specyfikacje produktu
| Marka: | SunBriteTV |
| Kategoria: | wspornik ścienny |
| Model: | SB-WM-ART2-XL-BL |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z SunBriteTV SB-WM-ART2-XL-BL, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje wspornik ścienny SunBriteTV
26 Września 2024
26 Września 2024
26 Września 2024
26 Września 2024
26 Września 2024
Instrukcje wspornik ścienny
- wspornik ścienny Tripp Lite
- wspornik ścienny Sanus
- wspornik ścienny Gembird
- wspornik ścienny My Wall
- wspornik ścienny V7
- wspornik ścienny One For All
- wspornik ścienny Manta
- wspornik ścienny Pyle
- wspornik ścienny Continental Edison
- wspornik ścienny TooQ
- wspornik ścienny Vogel's
- wspornik ścienny Hama
- wspornik ścienny Duronic
- wspornik ścienny Goobay
- wspornik ścienny Schwaiger
- wspornik ścienny Vivanco
- wspornik ścienny Newstar
- wspornik ścienny Speaka
- wspornik ścienny B-tech
- wspornik ścienny VCM
Najnowsze instrukcje dla wspornik ścienny
27 Września 2024
27 Września 2024
27 Września 2024
27 Września 2024
27 Września 2024
27 Września 2024
27 Września 2024
26 Września 2024
26 Września 2024
24 Września 2024