Instrukcja obsługi SunBriteTV SB-CM-T-L-BL

SunBriteTV nieskategoryzowany SB-CM-T-L-BL

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla SunBriteTV SB-CM-T-L-BL (8 stron) w kategorii nieskategoryzowany. Ta instrukcja była pomocna dla 6 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/8
SB-CM-T-L-BL
SB-CM-DT-L-BL
Weatherproof Universal Single & Dual Ceiling Mount
for Large TVs
INSTALLATION MANUAL
2
WARNING
•We highly recommend this product be installed by a qualied professional.
•Please do not begin installation until you have thoroughly read and understood these instructions.
•This mount supports display mounting from VESA 200x200 up to 700X500.
•This mount supports a maximum load of 175 lbs (79.5 kg).
•Ensure the ceiling will safely support the combined weight of the mount and your chosen display.
•The manufacturer does not accept responsibility for incorrect installation.
CAUTION:
These ceiling mounts are intended for use only with the maximum weight of 175 lbs (79.5 kg).
SPECIFICATIONS BOX CONTENTS TOOLS REQUIRED
•Power Drill
•3/16” (5mm) Drill Bit
•5/16” (8mm) Masonry Bit
•1/2" (13mm) Wrench
•Phillips Head Screw Driver
•Ceiling Plate Assembly (1)
•Mounting Head (1)
•Adapter Plate (1/2)
•TV Arms (2/4)
•18" Fixed Extension Pole (1)
•Hardware Kit (1) •3/8” Socket Wrench
•Maximum Load: 175 lbs (79.5 kg)
•Extension: 18 inches
•Stainless Steel Mounting Hardware
•Pan/Swivel Range: 360°
•Tilt Range: +0° /-20°
•Weather Resistant Coating
•VESA patterns: 200x200 up to
700X500
•7/16” Socket Wrench
HARDWARE KIT CONTENTS
M6 x 12mm Philips
Head Screw (x4/8)
M8 x 16mm Philips
Head Screw (x4/8)
Allen Wrench 2.5mm,
Security (x )1
Allen Wrench,
4mm (x1)
M4 x 20mm Philips
Head Screw (x4/8)
M5 x 30mm Philips
Head Screw (x4/8)
M6 x 30mm Phillips
Head Screw (x4/8)
M8 x 20mm Phillips
Head Screw (x4/8)
M8 x 40mm Phillips
Head Screw (x4/8)
M8 Nylock Nut (x4/8)
M5 x 12mm Philips
Head Screw (x4/8)
M6 x 20mm Philips
Head Screw (x4/8)
Security Wrench (x1)
M5 (16 x 5.3 x 1.5mm)
Metal Washer (x4/8)
#14 x 2.5” Lag Screw (x )6
M8 (20.5 x 8.5 x 2mm)
Metal Washer (x1 / )8 30
Locking Pin (x1/2)
M4/M5/M6 spacer:
12mm (x4/8)
M6/M8 Spacer:
17.8mm (x4/8) M5 x mm Set Screw (x )4 6
M4 x 12mm Philips
Head Screw (x4/8)
M6 (17.8 x 6.5 x 1.5mm)
Metal Washer (x4 )/8
M Nylock Nut (x10 1)
M10 x 65mm Bolt 1 (x )
3
INSTALLATION
Step 1: Mark Mounting Hole Locations
Place the ceiling plate on the mounting surface and mark the mounting
hole locations.
Step 2: Mount the Ceiling Plate
For Mounting on a Wood Joist (Fig 1)
a. Drill four holes into joist using a 3/16” drill bit. Be sure to drill into the
center of the joists.
b. Insert four lag screws into holes through the ceiling plate and tighten
down.
WARNING: Tighten screws so that the ceiling plate is rmly
attached, but do not over tighten. Over-tightening can damage
the screws, greatly reducing their holding strength.
For Mounting on a Concrete Ceiling (Fig 2)
NOTE: Concrete anchors not provided. 5/16” x 2-1/2” Red Head®
Hex Sleeve Anchors, #50113, are recommended for concrete or
cinder block installation.
WARNING: When installing ceiling plate on cinder block, verify rst
that you have a minimum of 1-3/8” of concrete thickness to be used
for the concrete wall anchors (not included). Do not drill into mortar
joints! Be sure to mount in a solid part of the block, generally
1”minimum from the side of the block. Cinder block must meet
ASTM C-90 specications. It is suggested that a standard electric
drill on slow setting is used to drill the hole instead of a hammer
drill to avoid breaking out the back of the hole when entering a void
or cavity.
Concrete must be 2000 psi density minimum. Lighter density
concrete may not hold anchor.
a. Drill four holes into concrete using 5/16” masonry bit. Insert hex sleeve
anchors (not supplied) and insert per instructions included with wall
anchors.
b. Remove washer and nut from end of bolt from all four anchor studs.
Place ceiling plate over bolts so they align with the four holes in ceiling
plate.
c. Re-install washer and nut onto end of bolt and tighten down using a
7/16” socket wrench until secure per instructions included with wall
anchors.
WARNING: Tighten screws so that the ceiling plate is rmly
attached, but do not over tighten. Over-tightening can damage
the screws, greatly reducing their holding strength.
Step 3: Attach the Extension Pole
Thread in extension pipe so that the holes in the pipe align with the holes
in the bracket, then tighten the through-bolt and tighten the set screw
(Fig 3).
Fig 1
Fig 2
Fig 3

Specyfikacje produktu

Marka: SunBriteTV
Kategoria: nieskategoryzowany
Model: SB-CM-T-L-BL

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z SunBriteTV SB-CM-T-L-BL, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje nieskategoryzowany SunBriteTV

SunBriteTV

SunBriteTV SB-CM-T-L-BL Instrukcja

26 Września 2024
SunBriteTV

SunBriteTV 4600HD SB-DP46XA Instrukcja

26 Września 2024
SunBriteTV

SunBriteTV SB-WM-F-M-BL Instrukcja

26 Września 2024
SunBriteTV

SunBriteTV SB-WM-T-M-BL Instrukcja

26 Września 2024

Instrukcje nieskategoryzowany

Najnowsze instrukcje dla nieskategoryzowany

Meec Tools

Meec Tools 010-084 Instrukcja

6 Października 2024
Outwell

Outwell Scenic Road 250 Instrukcja

5 Października 2024
Impact

Impact Qualite QL-3560-LED Instrukcja

4 Października 2024
Impact

Impact QuikBalance Instrukcja

4 Października 2024
Impact

Impact CA-112 Instrukcja

4 Października 2024
Impact

Impact Forever Ready Cool FRC-24-LED Instrukcja

4 Października 2024
Impact

Impact LS-BHA Instrukcja

4 Października 2024
Impact

Impact LKB-5C Instrukcja

4 Października 2024
Impact

Impact Varipole Drop Ceiling Adapter Instrukcja

4 Października 2024
Impact

Impact RST-001 Instrukcja

4 Października 2024