Instrukcja obsługi Sun Joe SJH901E
Sun Joe
nożyce do żywopłotu
SJH901E
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Sun Joe SJH901E (48 stron) w kategorii nożyce do żywopłotu. Ta instrukcja była pomocna dla 13 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek
Strona 1/48
© 2022 by Snow Joe, LLC
All rights reserved. Original instructions. SAVE THESE INSTRUCTIONS
1
EN
A Division of Snow Joe
®, LLC
R
OPERATOR’S MANUAL
Model SJH901E Form No. SJ-SJH901E-880E-MR4
ELECTRIC TELESCOPING
POLE HEDGE TRIMMER
18-INCH | 3.8-AMP
IMPORTANT!
Safety Instructions
All Operators Must Read These
Instructions Before Use
Always follow these safety guidelines. Failure to do so may
result in serious bodily injury or death.
General Safety WARNINGS!
You and any other operator of this pole hedge trimmer must
read, understand, and follow these instructions in their entirety.
Failure to follow these instructions may result in ELECTRIC
SHOCK, FIRE PERSONAL INJURY. , and/or serious
Notice the personal safety alert symbol m used in this
manual to draw your attention to a given along WARNING
with the particular operating instruction. This means that
the operation requires special ATTENTION, CAUTION, and
AWARENESS.
mWARNING! This unit can be dangerous! Careless or
improper use can cause serious injury.
mWARNING! The moving blades can cut you. Keep
hands and feet away from the blades and the cutting area.
Before using the pole hedge trimmer, familiarize yourself with
the controls, especially how to stop the pole hedge trimmer
in an emergency. The only individuals who should use the
pole hedge trimmer are those who thoroughly understand
these instructions and know how to properly operate the unit.
Children should never be allowed access to the pole hedge
trimmer.
Retain this manual for future reference and reread it at the start
of each trimming season.
1. Keep work area clean and well-lit – Cluttered, dark
areas invite accidents.
2. Replacement parts – When servicing this unit, use only
identical replacement parts. Replace or repair damaged
cords immediately.
3. Keep children, bystanders, and pets away – All
spectators, including pets, should be kept a safe distance
away from the work area.
4. Know your product – Know how to start and stop the
machine. Be thoroughly familiar with the controls.
5. Use the right tool – Do not use this machine for any job
except that for which it was intended.
6. Extension cords – To prevent electric shock, use only
with an extension cord suitable for outdoor use.
7. Avoid accidental starting – Do not carry the pole hedge
trimmer with your nger on the switch. Make sure the
switch is o before plugging in or unplugging the unit.
mCAUTION! Moving parts will continue to run for several
seconds after turning o the machine.
8. Do not abuse the cord – Never carry the pole hedge
trimmer by the cord or yank the cord to disconnect it from
the receptacle. Keep the cord away from heat, oil, and
sharp edges.
9. Moving parts – Keep hands and feet away from moving
parts. Keep guards in place and in proper working order.
10. Do not force the tool – It will perform better with less
likelihood of personal or mechanical injury if it is used at
the rate for which it was designed.
11. Do not overreach – Keep proper footing and balance at
all times.
12. Use safety glasses – Also use safety footwear, snug-
tting clothing, protective gloves, hearing, and head
protection.
13. Disconnect the tool – Disconnect the pole hedge
trimmer from the power supply when it is not in use,
before servicing it, when changing accessories, and when
performing any other maintenance task.
14. Store idle tool indoors – When not in use, the pole hedge
trimmer should be stored indoors in a dry and high or
locked-up place out of the reach of children.
15. Maintain the pole hedge trimmer with care – Keep the
cutting edges sharp and clean for optimal performance
and to reduce the risk of injury. Inspect the extension
cord periodically and immediately replace it if damaged.
Keep the handles dry, clean, and free from oil and grease.
Follow the additional recommendations described in the
maintenance section of this manual.
16. Avoid dangerous environments – Do not use the pole
hedge trimmer in rain or in damp or wet locations. Do not
operate the pole hedge trimmer in gaseous or explosive
atmospheres or use the pole hedge trimmer near
ammable or combustible liquids. Motors in these tools
normally spark, and the sparks might ignite fumes.
2
17. Stay alert – Watch what you are doing. Use common
sense. Do not operate the pole hedge trimmer when you
are tired or under the inuence of drugs, alcohol, or other
medication.
18. Check for damaged parts – Before further use of the
appliance, a guard or other part that is damaged should
be carefully checked to determine that it will operate
properly and perform its intended function. Check for
alignment of moving parts, binding of moving parts,
breakage of parts, mounting, and any other condition
that may aect its operation. A guard or other part that
is damaged should be properly repaired or replaced.
Contact the Snow Joe® + Sun Joe® customer service
center at 1-866-SNOWJOE (1-866-766-9563) for
assistance.
Additional Safety Rules for Pole
Hedge Trimmer
1. Remove any adjusting key or wrench before turning
the power tool on. A wrench or key left attached to the
rotating part of the power tool may result in personal
injury.
2. If devices or facilities are available for the extraction and
collection of dust, ensure these are connected or properly
used. Use of these devices can reduce dust related
hazards.
3. Remove any blade that has been damaged. Always make
sure that the blade is installed correctly and securely
fastened before each use. Failure to do so can cause
serious injury.
4. Hold the pole hedge trimmer by insulated gripping
surfaces only, because the cutter blade may contact
hidden wiring or its own cord. Cutter blades contacting a
"live" wire may electrify exposed metal parts of the power
tool and could give the operator an electric shock.
5. Maintain a rm grip on the handle and pole while cutting
with the blade. Keep the blade away from body.
6. Hold pole hedge trimmer properly, e.g., with both hands
if two handles are provided. Loss of control can cause
personal injury.
7. Keep extension cord away from cutting area. During
operation the extension cord may be hidden in shrubs and
can be accidentally cut by the blade.
8. Check the hedge for foreign objects before operation,
e.g., center fences. Take care that the cutting device does
not come in contact with wire or other metal objects.
9. Service on the product must be performed by qualied
repair personnel only. Service or maintenance performed
by unqualied personnel could result in injury to the user
or damage to the product.
10. If the power supply cord is damaged, it must be replaced
only by the manufacturer or by an authorized service
center to avoid risk.
11. Keep all parts of the body away from the cutting blade. Do
not remove cut material or hold material to be cut when
blades are moving. Make sure the switch is o when clearing
jammed material. A moment of inattention while operating
the pole hedge trimmer may result in serious personal injury.
12. Carry the pole hedge trimmer by the handle with the
cutting blade stopped. When transporting or storing
the pole hedge trimmer always keep the blade covered.
Proper handling of the pole hedge trimmer will reduce
possible personal injury from the cutter blades.
13. Do not use the pole hedge trimmer if the switch does not
turn it on and o. Any power tool that cannot be controlled
with the switch is dangerous and must be repaired.
14. Use the pole hedge trimmer and accessories in
accordance with these instructions, taking into account
the working conditions and the work to be performed. Use
of the power tool for operations dierent from intended
use could lead to a hazardous situation.
15. The product should be supplied via a residual current
device (RCD) with a tripping current of not more than
30 mA.
Training
1. Read the instructions carefully. Be familiar with the
controls and the proper use of the product.
2. Never allow people unfamiliar with these instructions or
children to use the product. Local regulations can restrict
the age of the operator.
3. Keep in mind that the operator or user is responsible for
accidents or hazards occurring to other people or their
property.
Preparation
1. This product can cause serious injuries. Read the
instructions carefully for the correct handling, preparation,
maintenance, starting and stopping of the product.
Become familiar with all controls and the proper use of the
product.
2. Never allow children to use the pole hedge trimmer.
3. Beware of overhead power lines.
4. Never operate the product while people, especially
children, or pets are nearby.
5. Dress properly. Do not wear loose clothing or jewellery,
which can be caught in moving parts. Use of sturdy
gloves, non-skid footwear and safety glasses is
recommended.
6. Wear eye protection and stout shoes at all times while
operating the product.
7. If the cutting attachment strikes any foreign object or the
product starts making any unusual noise or vibration, shut
o the power source and allow the product to stop.
3
Switch the product o, disconnect it from the power supply
and take the following steps:
– inspect for damage;
– check for, and tighten, any loose parts;
– have any damaged parts replaced or repaired with parts
having equivalent specications.
Operation
1. Use the product only in daylight or good articial light.
2. Never operate the product with damaged guards or
shields or without guards or shields in place.
3. Keep hands and feet away from the cutting device at all
times and especially when switching on the motor.
4. Before using the product and after any impact, check for
signs of wear or damage and repair as necessary.
5. Always disconnect the product from the power supply
(i.e., remove the plug from the power supply)
– whenever leaving the product unattended;
– adjusting the working position of the cutting device;
– before clearing a blockage;
– before checking, cleaning or working on the product;
– after striking a foreign object;
– whenever the product starts vibrating abnormally.
6. Ensure that the pole hedge trimmer is correctly located in
a designated working position before starting the motor.
7. While operating the pole hedge trimmer, always ensure
that the operating position is safe and secure, especially
when using steps or a ladder.
8. Do not operate the pole hedge trimmer with a damaged or
excessively worn cutting device.
9. Always ensure that all handles and guards are tted when
using the pole hedge trimmer. Never attempt to use an
incomplete pole hedge trimmer or one tted with an
unauthorized modication.
10. Always use two hands to operate a pole hedge trimmer
tted with two handles.
11. Always be aware of your surroundings and stays alert for
possible hazards of which you may not be aware due to
the noise of the product.
12. Take care against injury to feet and hands from the cutting
device.
13. Always ensure that the air vents are kept clear of debris.
14. Wear slip-resistant foot protection and protective clothing
when using this product.
15. Always keep proper footing and operate the product
only when standing on a xed, secure and level surface.
Change working positions regularly to avoid tiredness and
ensure a comfortable working position at all times.
16. Never use replacement parts or accessories not provided
or recommended by the manufacturer.
17. The use of this product may be restricted by regional or
local regulations.
Vibration + Noise Reduction
To reduce the impact of noise and vibration emission, limit the
time of operation, use low-vibration and low-noise operating
modes as well as wear personal protective equipment.
Take the following points into account to minimise the vibration
and noise exposure risks.
1. Only use the product as intended by its design and these
instructions.
2. Ensure that the product is in good condition and well
maintained.
3. Use correct attachments for the product and ensure they
are in good condition.
4. Keep tight grip on the handles/grip surface.
5. Maintain this product in accordance with these
instructions and keep it well lubricated (where
appropriate).
6. Plan your work schedule to spread any high vibration tool
use across a longer period of time.
Emergency
Familiarize yourself with the use of this product by means of
this instruction manual. Memorize the safety directions and
follow them to the letter. This will help to prevent risks and
hazards.
1. Always be alert when using this product, so that you can
recognize and handle risks early. Fast intervention can
prevent serious injury and damage to property.
2. Switch o and disconnect from the power supply if there
are malfunctions. Have the product checked by a qualied
professional and repaired, if necessary, before you
operate it again.
Residual Risks
Even if you are operating this product in accordance with all
the safety requirements, potential risks of injury and damage
remain. The following dangers can arise in connection with the
structure and design of this product:
1. Health defects resulting from vibration emission if the
product is being used over long periods of time or not
adequately handled and properly maintained.
2. Injuries and damage to property due to broken cutting
attachments or the sudden impact of hidden objects
during use.
3. Danger of injury and property damage caused by ying
objects.
Specyfikacje produktu
| Marka: | Sun Joe |
| Kategoria: | nożyce do żywopłotu |
| Model: | SJH901E |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z Sun Joe SJH901E, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje nożyce do żywopłotu Sun Joe
31 Grudnia 2025
31 Grudnia 2025
14 Września 2024
12 Września 2024
9 Września 2024
8 Września 2024
6 Września 2024
4 Września 2024
4 Września 2024
1 Września 2024
Instrukcje nożyce do żywopłotu
- nożyce do żywopłotu Worx
- nożyce do żywopłotu Honda
- nożyce do żywopłotu Milwaukee
- nożyce do żywopłotu Stihl
- nożyce do żywopłotu Bosch
- nożyce do żywopłotu Parkside
- nożyce do żywopłotu Cramer
- nożyce do żywopłotu Stiga
- nożyce do żywopłotu Kärcher
- nożyce do żywopłotu MacAllister
- nożyce do żywopłotu Stanley
- nożyce do żywopłotu Black & Decker
- nożyce do żywopłotu Scheppach
- nożyce do żywopłotu Grizzly
- nożyce do żywopłotu Gardena
- nożyce do żywopłotu DeWalt
- nożyce do żywopłotu Einhell
- nożyce do żywopłotu Remington
- nożyce do żywopłotu Hyundai
- nożyce do żywopłotu Husqvarna
- nożyce do żywopłotu Makita
- nożyce do żywopłotu Ozito
- nożyce do żywopłotu Fuxtec
- nożyce do żywopłotu RYOBI
- nożyce do żywopłotu NAC
- nożyce do żywopłotu Wolf Garten
- nożyce do żywopłotu Eurogarden
- nożyce do żywopłotu Handy
- nożyce do żywopłotu DEDRA
- nożyce do żywopłotu Garden Feelings
- nożyce do żywopłotu Baumr-AG
- nożyce do żywopłotu Sovereign
- nożyce do żywopłotu CMI
- nożyce do żywopłotu Sterwins
- nożyce do żywopłotu Trotec
- nożyce do żywopłotu Meec Tools
- nożyce do żywopłotu AL-KO
- nożyce do żywopłotu Güde
- nożyce do żywopłotu Texas
- nożyce do żywopłotu ATIKA
- nożyce do żywopłotu Bavaria
- nożyce do żywopłotu Zipper
- nożyce do żywopłotu Flymo
- nożyce do żywopłotu Florabest
- nożyce do żywopłotu Hanseatic
- nożyce do żywopłotu Solo
- nożyce do żywopłotu Ferrex
- nożyce do żywopłotu Brandson
- nożyce do żywopłotu Ergotools Pattfield
- nożyce do żywopłotu Ferm
- nożyce do żywopłotu Hitachi
- nożyce do żywopłotu Craftsman
- nożyce do żywopłotu Fieldmann
- nożyce do żywopłotu Homelite
- nożyce do żywopłotu Shindaiwa
- nożyce do żywopłotu Gardenline
- nożyce do żywopłotu PowerPlus
- nożyce do żywopłotu Vonroc
- nożyce do żywopłotu Spear & Jackson
- nożyce do żywopłotu HiKOKI
- nożyce do żywopłotu McCulloch
- nożyce do żywopłotu Proviel
- nożyce do żywopłotu Metabo
- nożyce do żywopłotu Bestgreen
- nożyce do żywopłotu Hoberg
- nożyce do żywopłotu EGO
- nożyce do żywopłotu Cotech
- nożyce do żywopłotu Skil
- nożyce do żywopłotu Cocraft
- nożyce do żywopłotu Greenworks
- nożyce do żywopłotu Yellow Garden Line
- nożyce do żywopłotu Challenge
- nożyce do żywopłotu Powerworks
- nożyce do żywopłotu Tel Sell
- nożyce do żywopłotu Tanaka
- nożyce do żywopłotu Troy-Bilt
- nożyce do żywopłotu Topcraft
- nożyce do żywopłotu Martha Stewart
- nożyce do żywopłotu Gamma
- nożyce do żywopłotu Kress
- nożyce do żywopłotu Dolmar
- nożyce do żywopłotu McGregor
- nożyce do żywopłotu Qualcast
- nożyce do żywopłotu Varo
- nożyce do żywopłotu Pattfield
- nożyce do żywopłotu Kibani
- nożyce do żywopłotu Echo
- nożyce do żywopłotu Maruyama
- nożyce do żywopłotu Grouw
- nożyce do żywopłotu Batavia
- nożyce do żywopłotu Gtech
- nożyce do żywopłotu Levita
- nożyce do żywopłotu Efco
- nożyce do żywopłotu Black Decker
- nożyce do żywopłotu Gartenmeister
- nożyce do żywopłotu Lux Tools
- nożyce do żywopłotu Verto
- nożyce do żywopłotu Anova
- nożyce do żywopłotu Hurricane
- nożyce do żywopłotu Budget
- nożyce do żywopłotu Challenge Xtreme
- nożyce do żywopłotu Deltafox
- nożyce do żywopłotu Palmera
- nożyce do żywopłotu Yardforce
- nożyce do żywopłotu Powerpeak
- nożyce do żywopłotu Toledo
- nożyce do żywopłotu Kaaz
- nożyce do żywopłotu Garden Groom
- nożyce do żywopłotu Mr Gardener
- nożyce do żywopłotu Kingcraft
- nożyce do żywopłotu Mac Allister
- nożyce do żywopłotu Jonsered
- nożyce do żywopłotu Robust
- nożyce do żywopłotu LawnMaster
- nożyce do żywopłotu G-Technology
- nożyce do żywopłotu Maxbear
- nożyce do żywopłotu Turbo-Silent
Najnowsze instrukcje dla nożyce do żywopłotu
13 Stycznia 2025
12 Stycznia 2025
7 Stycznia 2025
3 Stycznia 2025
29 Grudnia 2024
29 Grudnia 2024
29 Grudnia 2024
29 Grudnia 2024
29 Grudnia 2024
29 Grudnia 2024