Instrukcja obsługi Sun Joe 24V-TB-CT
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Sun Joe 24V-TB-CT (48 stron) w kategorii Zszywacz. Ta instrukcja była pomocna dla 6 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek
Strona 1/48
© 2021 by Snow Joe
®, LLC
All rights reserved. Original instructions. SAVE THESE INSTRUCTIONS
1
EN
A Division of Snow Joe
®, LLC
R
OPERATOR’S MANUAL
Model 24V-TB-CT Form No. SJ-24V-TB-CT-880E-MR2
CORDLESS COMPACT TURBINE
JET BLOWER – TOOL ONLY
24-VOLT MAX* | 100 MPH
IMPORTANT!
Safety Instructions
All Operators Must Read These
Instructions Before Use
Read all the instructions contained in this manual. Keep this
manual in a safe place, so that the information is available at
all times. If you give the equipment to another person,
make sure to provide these operating instructions. Basic safety
precautions should always be followed to reduce the risk of
re, electric shock, and personal injury.
mDANGER! This indicates a hazardous situation, which,
if not followed, will result in serious injury or death.
mWARNING! This indicates a hazardous situation, which,
if not followed, could result in serious injury or death.
mCAUTION! This indicates a hazardous situation, which,
if not followed, could result in minor or moderate injury.
Improper use of the machine will invalidate the warranty,
relieve the manufacturer from all liabilities. The user will
consequently be liable for all and any damage or injury to
himself/herself or others.
General Safety
FOR HOUSEHOLD USE ONLY
mCAUTION! Wear appropriate hearing protection during
use. After long periods of extended use, the noise generated
from this appliance may cause hearing loss if your ears are
not properly protected.
mWARNING! When using the power tool, basic safety
precautions should always be followed to reduce the risk of
re, electric shock, and personal injury. These include:
1. Keep work area clean and well-lit – Cluttered, dark
areas invite accidents.
2. Replacement parts – When servicing this unit, use only
identical replacement parts.
3. Keep children, bystanders, and pets away –
All spectators, including pets, should be kept a safe
distance away from the work area.
4. Dress properly – Do not wear loose clothing or jewelry
as such articles can get caught in moving parts. Wear a
protective covering to contain long hair. Wearing rubber
gloves and substantial non-slip footwear is recommended
when working outdoors.
5. Prevent unintentional starting – Ensure the switch is in
the o-position before connecting to battery pack, picking
up or carrying the appliance. Carrying the appliance with
your nger on the switch or energizing an appliance that
has the switch on invites accidents.
6. Disconnect battery pack before cleaning or servicing –
Disconnect the battery pack from the appliance before
making any adjustments, changing accessories, or
storing. Such preventive safety measures reduce the risk
of starting the appliance accidentally.
mWARNING! Do not modify or attempt to repair the
appliance or the battery pack (as applicable) except as
indicated in the instructions for use and care.
7. Moving parts – Keep hands and feet away from moving
parts. Keep guards in place and in proper working order.
8. Do not force the tool – It will perform better with less
likelihood of personal or mechanical injury if it is used at
the rate for which it is designed.
9. Wear personal protective equipment – When using this
tool, wear safety glasses with side shields or goggles to
provide necessary eye protection. Wear ear defenders to
prevent hearing damage. Use a face or dust mask if the
work environment is dusty.
10.
Remove the battery – Remove the battery when the tool is
not in use, before servicing it, when changing accessories,
and when performing any other maintenance task.
11. Store idle tool indoors – When not in use, the blower
should be stored indoors in a dry and high or locked-up
place out of the reach of children.
12. Use the right tool – Do not use the tool for any job except
that for which it is intended.
13. Avoid dangerous environments – Do not use the blower
in rain, damp, or wet locations.
14. Stay alert – Watch what you are doing. Use common
sense. Do not operate the blower when you are tired or
under the inuence of drugs, alcohol, or other medication.
Additional Safety Instructions
• Do not use the blower in the rain or in a damp area.
• Use extra care when cleaning on stairs or steps.
2
•
Keep rm footing and maintain good balance at all times. Do
not overreach. Overreaching can result in loss of balance.
• Turn o all controls before unplugging the tool.
• Do not use the tool if the power switch does not turn it ON
or OFF. Any tool that cannot be controlled with the switch is
dangerous and must be repaired.
• Carefully inspect your appliance prior to use and follow all
label and marking instructions.
• Keep all parts of your body away from any moving parts
and all hot surfaces of the unit.
• Do not put any object into the tool's openings. Do not use
the tool with any opening blocked; keep openings free of
dust, lint, hair, or any other object that may reduce air ow.
• Check the work area before each use. Remove all objects
such as rocks, broken glass, nails, wire, or string, which can
be thrown or become entangled in the machine.
• Service on the product must be performed by qualied
repair personnel only. Service or maintenance performed
by unqualied personnel could result in injury to the user or
damage to the product.
• This blower is intended for residential use only. Commercial
use of this product is prohibited and will void the
manufacturer's warranty.
• Never run the unit without the proper equipment attached.
Always ensure the blower tube is properly installed.
• Always grasp the handle when operating the unit,
only operate the machine in its intended orientation.
Specic Safety Rules For
Jet Blower
• The jet blower has been designed to clear light debris and
leaves from hard surfaces – not for clearing grassed areas.
• When operating the unit, never point the jet blower nozzle
in the direction of people or pets or in the direction of
windows. Use extra caution when blowing debris near solid
objects, such as trees, automobiles, and walls.
• Be sure to secure the unit when transporting it.
• Never douse or squirt the unit with water or any other liquid.
Clean the unit after each use as described in the cleaning
and storage section.
Battery & Charger
Safety Instructions
NOTE: This unit is the tool only. The battery and the charger
are not included. They must be purchased separately.
Model 24V-TB-CT is compatible with the 24V iON+ System
batteries and chargers. See page 12 for more information.
We pay a great deal of attention to the design of every battery
pack to ensure that we supply you with batteries that are safe,
durable and have a high energy density. The battery cells have
a wide range of safety devices. Each individual cell is initially
formatted and its electrical characteristic curves are recorded.
This data is then used exclusively to be able to assemble the
best possible battery packs.
Despite all the safety precautions, caution must always be
exercised when handling batteries. The following points must
be obeyed at all times to ensure safe use. Safe use can only
be guaranteed if undamaged cells are used. Incorrect handling
of the battery pack can cause cell damage.
IMPORTANT! Analyses conrm that incorrect use and poor
care of high-performance batteries are the main factors
responsible for personal and/or product damage.
mWARNING! Use only approved replacement batteries;
other batteries may damage the jet blower and cause it to
malfunction.
mCAUTION! To reduce the risk of injury, charge the
24V iON+ lithium-ion battery pack only in its designated
24V iON+ lithium-ion charger. Other types of chargers present
risk of re, personal injury and damage. Do not wire a battery
pack to a power supply plug or car cigarette lighter. Such
misuse will permanently disable or damage the battery pack.
• Avoid dangerous environments – Do not charge the
battery pack in rain, snow or in damp or wet locations.
Do not use the battery pack or charger in the presence of
explosive atmospheres (gaseous fumes, dust or ammable
materials) because sparks may be generated when inserting
or removing the battery pack, which could lead to a re.
• Charge in a well-ventilated area – Do not block the
charger vents. Keep them clear to allow for proper
ventilation. Do not allow smoking or open ames near a
charging battery pack. Vented gases may explode.
The safe temperature range for the battery is NOTE:
41°F – 105ºF (5°C – 40.5°C). Do not charge the battery
outside in freezing weather; charge it at room temperature.
• Maintain charger cord – When unplugging the charger,
pull the plug, not the cord, from the receptacle to reduce
the risk of damage to the electrical plug and cord.
Never carry the charger by its cord or yank it by the cord
to disconnect it from the receptacle. Keep the cord away
from heat, oil and sharp edges. Make sure the cord will not
be stepped on, tripped over or subjected to damage or
stress when the charger is in use. Do not use the charger
with a damaged cord or plug. Replace a damaged charger
immediately.
• Do not use an extension cord unless it is absolutely
necessary – Using the wrong, damaged or improperly
wired extension cord poses a risk of re and electric shock.
If an extension cord must be used, plug the charger into a
properly wired 16 gauge or larger extension cord with the
female plug matching the male plug on the charger. Make
sure that the extension cord is in good electrical condition.
• Check the rated input for the charger before using –
The charger must be plugged into an appropriate
receptacle.
• Use only recommended attachments – Use of an
attachment not recommended or sold by the battery
charger or battery pack manufacturer may result in risk of
re, electric shock or personal injury.
• Unplug charger when not in use – Make sure to remove
battery packs from unplugged chargers.
3
mWARNING! To reduce the risk of electric shock,
always unplug the charger before performing any cleaning
or maintenance. Do not allow water to ow into the charger.
Use a Ground Fault Circuit Interrupter (GFCI) to reduce shock
hazards.
• Do not burn or incinerate battery packs – Battery packs
may explode, causing personal injury or damage.
Toxic fumes and materials are created when battery packs
are burned.
• Do not crush, drop or damage battery packs – Do not
use the battery pack or charger if they have sustained a
sharp blow, been dropped, run over or have been damaged
in any way (i.e. pierced with a nail, hit with a hammer,
stepped on, etc.).
• Do not disassemble – Incorrect reassembly may pose
a serious risk of electric shock, re or exposure to toxic
battery chemicals. If the battery or charger are damaged,
please contact an authorized Snow Joe® + Sun Joe® dealer
or call the Snow Joe® + Sun Joe® customer service center
at 1-866-SNOWJOE (1-866-766-9563).
• Never let a Battery chemicals cause serious burns –
damaged battery pack contact the skin, eyes or mouth. If a
damaged battery pack leaks battery chemicals, use rubber
or neoprene gloves to safely dispose of it. If skin is exposed
to battery uids, wash the aected area with soap and
water and rinse with vinegar. If eyes are exposed to battery
chemicals, immediately ush with water for
20 minutes and seek medical attention. Remove and
dispose of contaminated clothing.
• Store your battery pack and charger in a cool, dry
place – Do not store the battery pack or charger where
temperatures may exceed 105ºF (40.5ºC), such as in direct
sunlight or inside a vehicle or metal building during the
summer.
mWARNING! Read all safety warnings and instructions
Failure to follow the warnings and instructions may
result in electric shock, re and/or serious injury
Information about the battery
1. The battery pack supplied with your cordless turbine jet
blower is only partially charged. The battery pack has to
be charged completely before you use the tool for the rst
time.
2. For optimum battery performance, avoid low discharge
cycles by charging the battery pack frequently.
3. Store the battery pack in a cool place, ideally at 77°F
(25°C) and charged fully.
4. Lithium-ion batteries are subject to a natural aging
process. The battery pack must be replaced at the latest
when its capacity falls to just 80% of its capacity when
new. Weakened cells in an aged battery pack are no
longer capable of meeting the high power requirements
needed for the proper operation of your jet blower,
and therefore pose a safety risk.
5. Do not throw battery packs into an open re as this poses
a risk of explosion.
6. Do not ignite the battery pack or expose it to re.
7. Do not exhaustively discharge batteries. Exhaustive
discharge will damage the battery cells. The most
common cause of exhaustive discharge is lengthy storage
or non-use of partially discharged batteries. Stop working
as soon as the performance of the battery falls noticeably
or the electronic protection system triggers. Place the
battery pack in storage only after it has been fully charged.
8. Protect batteries and the tool from overloads. Overloads
will quickly result in overheating and cell damage inside
the battery housing even if this overheating is not apparent
externally.
9. Avoid damage and shocks. Immediately replace batteries
that have been dropped from a height of more than one
meter or those that have been exposed to violent shocks,
even if the housing of the battery pack appears to be
undamaged. The battery cells inside the battery may have
suered serious damage. In such instances, please read
the waste disposal information for proper battery disposal.
10. If the battery pack suers overloading and overheating,
the integrated protective cuto will switch o the
equipment for safety reasons.
IMPORTANT! Do not press the ON/OFF switch any more
if the protective cut-o has been activated. This may
damage the battery pack.
11. Recharge only with the charger specied by the
manufacturer. A charger that is suitable for one type of
battery pack may create a risk of re when used with
another battery pack.
12. Use appliances only with specically designated battery
packs. Use of any other battery packs may create a risk of
injury and re.
13. Under abusive conditions, liquid may be ejected from
the battery; avoid contact. If contact accidentally occurs,
ush with water. If liquid contacts eyes, additionally seek
medical help. Liquid ejected from the battery may cause
irritation or burns.
14. Do not use a battery pack or appliance that is damaged
or modied. Damaged or modied batteries may exhibit
unpredictable behavior resulting in re, explosion or risk of
injury.
15. Do not expose a battery pack or appliance to re or
excessive temperature. Exposure to re or temperature
above 266ºF (130°C) may cause explosion.
16. Follow all charging instructions and do not charge the
battery pack or appliance outside of the temperature
range specied in the instructions. Charging improperly
or at temperatures outside of the specied range may
damage the battery and increase the risk of re.
17. Prevent unintentional starting – Ensure the switch is in
the o-position before connecting to battery pack, picking
up or carrying the appliance. Carrying the appliance with
your nger on the switch or energizing an appliance that
has the switch on invites accidents.
Specyfikacje produktu
| Marka: | Sun Joe |
| Kategoria: | Zszywacz |
| Model: | 24V-TB-CT |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z Sun Joe 24V-TB-CT, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje Zszywacz Sun Joe
10 Września 2024
10 Września 2024
1 Września 2024
1 Września 2024
28 Sierpnia 2024
22 Sierpnia 2024
21 Sierpnia 2024
6 Sierpnia 2024
4 Lipca 2024
4 Lipca 2024
Instrukcje Zszywacz
- Zszywacz Fellowes
- Zszywacz President
- Zszywacz Milwaukee
- Zszywacz Bosch
- Zszywacz Parkside
- Zszywacz Whirlpool
- Zszywacz DeWalt
- Zszywacz Einhell
- Zszywacz Silverline
- Zszywacz Makita
- Zszywacz Rapid
- Zszywacz RYOBI
- Zszywacz DEDRA
- Zszywacz CTA Digital
- Zszywacz Rexel
- Zszywacz Hitachi
- Zszywacz Rapoo
- Zszywacz Craftsman
- Zszywacz Klein Tools
- Zszywacz Fieldmann
- Zszywacz PowerPlus
- Zszywacz Sencor
- Zszywacz HiKOKI
- Zszywacz Workzone
- Zszywacz Porter-Cable
- Zszywacz Metabo
- Zszywacz Proline
- Zszywacz Targus
- Zszywacz Kensington
- Zszywacz Aqua Joe
- Zszywacz Iluv
- Zszywacz Holzmann
- Zszywacz Surtek
- Zszywacz Werckmann
- Zszywacz Neo
- Zszywacz Syscom
- Zszywacz MSW
- Zszywacz Mannesmann
- Zszywacz Smart365
Najnowsze instrukcje dla Zszywacz
15 Października 2024
7 Października 2024
7 Października 2024
7 Października 2024
7 Października 2024
7 Października 2024
7 Października 2024
6 Października 2024
6 Października 2024
4 Października 2024