Instrukcja obsługi Stewart Systems EkoFill

Stewart Systems Niesklasyfikowane EkoFill

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Stewart Systems EkoFill (2 stron) w kategorii Niesklasyfikowane. Ta instrukcja była pomocna dla 4 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/2

EkoFill – E620 Fabric primer

EkoFill is our proprietary fabric primer that provided the UV barrier, Fire

protection, Seals the weave of the fabric, and is the primer for the top-coat of

paint.

3 cross coats are required. to seal the weave of the fabric and 1 brushed IN

2 sprayed ON to build up the required protection for the fabric. More can be

applied if desired.

The fabric must be cleaned with the EkoClean prior to application of the brushed coat of EkoFill to

remove contaminates.

Make sure to re-dampen the fabric with clean water so that the first

brushed coat will be more easily absorbed into the weave of the fabric. This

will help to avoid pinholes and brush marks. The idea of the brushed coat is to get EkoFill down

into the weave of the fabric. The fabric should be lightly dampened. It will dry quickly so only

dampen a few square yards at a time. It should not be soaking wet. You should not be able to

squeegee out any water from the fabric with your hand.

EkoFill dries quickly and the next coat can be applied as soon as the previous one has lo st itʼs

sheen and is dry to the touch with no color transfer.

Avoid sanding after the brushed coats of EkoFill. Remember that the goal of the brushed coat is

to the weave not the weave. too aggressive with sandpaper you will get EkoFill IN ON If you are

fuzz up the fabric and it will show through the sprayed coats. You can lightly wipe any trash or

lint off with 320 sand paper or red Scotch-Brite. Be very careful not to cut into the fabric itself.

Brushing EkoFill

Use a foam brush to apply the brushed coats of EkoFill into the damp fabric. Only wet out the

beveled tip of the brush and work the brush until it is dry before re-wetting with more EkoFill.

Avoid brushing Up the pinked edge of the finishing tapes. Bring the brush Down off the tapes into

the open bays to avoid pulling at the edge of the tape with the brush which tears little chunks of

foam off the brush and leaves residue on the surface and aggravates the smooth ironed down

pinked edge of the tapes. You will still see the glue through the EkoFill because the weave is

already sealed where the glue is. You will also notice that the tiny air bubbles go away by them

selves. Air bubbles come from being aggressive, pushing too hard and moving too fast which

introduces air into the EkoFill causing it to foam up. Do not keep pushing EkoFill around on the

fabric because as it starts to dry you will leave brush marks that must be sanded out later. If the

EkoFill goes from being slick to sticky stop brushing and let it lay down while it s still wet enough ʼ

to flow.

If you want to store parts until you are ready to start spraying now is a good time to do so. The

first brushed coat of EkoFill will help to protect the fabric. Cover with a clean bed sheet and store

away from the work area.

EkoFill – E620 Fabric primer

Spraying EkoFill

When spraying EkoFill you should apply a semi-wet coat that has a low gloss satin sheen to it.

Do not apply heavy wet coats. If you hold the spray gun too far away you will get a dry textured

finish. This will need to be sanded smooth since adding more EkoFill over the top will not level

out the imperfections. Read your spray gun manufactures instruction and make sure to do some

spray pattern tests before painting your aircraft. EkoFill can be applied using a 1.2-1.4mm

nozzle. It is sprayed as is no thinning required. “ ” Filter using an extra fine 120 micron paint

strainer as you pour it into the paint gun. Remove any fluid filters that may be between the

cup and gun body.

After 1 sprayed cross coat you should wait about 45 min to sand. Use 320 open coat sand paper

to remove any surface defects and to sand to a smooth surface. Lightly sand along the pinked

edge of all the finishing tapes to shear off the mic o fuzzy hairs that stand up from the edge of the r

finishing tapes. Do not be aggressive sanding the sensitive areas like pinked edges, rib stitching,

and over structure because you can cut into the weave of the fabric. Use red Scotch-Brite to buff

the surface and to scuff the EkoFill over sensitive areas where sandpaper would cut right through.

Areas where you sand down to the fabric must receive additional EkoFIll when spraying on the

next coat. The best way to do this is to fog in multiple light coats over the exposed fabric building

up the EkoFill before spraying out the entire surface. The smoother you prep the surface after the

first sprayed cross- coat of EkoFill the smoother the second sprayed cross coat will lay down. You

may continue to spray and sand to achieve your desired smoothness and amount of fill.

Waterborne coatings will not melt into and hide defects from the previous coat. They will only

amplify the surface they are being applied over. Take care to iron down pinked edges and to

sand rough edges smooth. You may continue to use the iron to remove defects and iron down

small air bubbles or lifting edges. aBe ware that the more EkoFill you put on the fabric the more

likely you are to smear the Ekofill around with the iron. Fix the fabric, Then fix the EkoFIll as

needed.

When sanding EkoFill ALWAYS use a tack-rag designed for use with waterborne coatings and

clean dry air blowing and wiping to remove sanding residue. You can also use a clean soft bristle

brush on a shop-vac to suck up the sanding residue before cleaning the surface with a tack-rag.

Waterborne coatings require a very clean surface to obtain maximum adhesion and avoid

surface defects in the final top coat paint. - Take care to remove all sanding residue. Do

not wet sand EkoFill. Do not wipe clean with a water soaked towel or use EkoClean to

remove sanding residue prior to painting. You may wipe with a low lint surface prep towel

using 91% isopropyl alcohol but do not scrub, just lightly wipe. Alcohol will soften the

EkoFill and if you are too aggressive you will leave lint imbedded into the Ekofill from the

surface prep towel.

Clean up with soap and water. Diluted EkoClean works quite well. Any remaining residue may

be removed with lacquer thinner.

Recommended temp range for application 60- -85 deg F. 15 75% humidity

Recommended wet film thickness 2.5 mil

Dry time before top-coating @ 75 deg F. 8- 10 hours

Specyfikacje produktu

Marka:	Stewart Systems
Kategoria:	Niesklasyfikowane
Model:	EkoFill

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Stewart Systems EkoFill, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą

Twoje imię*

Twój email*

Napisz tutaj swoje pytanie

Instrukcje Niesklasyfikowane Stewart Systems

Stewart Systems EkoFill Instrukcja

28 Września 2024

Instrukcje Niesklasyfikowane

Najnowsze instrukcje dla Niesklasyfikowane

Black Diamond BD1121530000ALL1 Instrukcja

15 Października 2024

Husqvarna K 970 SmartGuard Instrukcja

15 Października 2024

Stihl HT 70 Instrukcja

15 Października 2024

Ernesto H14270 Instrukcja

15 Października 2024

Uniden BT MIC KIT Instrukcja

15 Października 2024

Vaude Omnis Bike 26 Instrukcja

15 Października 2024

ART ProChannel II Instrukcja

15 Października 2024

Aukey DR02J Instrukcja

15 Października 2024

Master Lock 653EURD Instrukcja

15 Października 2024

Roland FR-18 Diatonic Instrukcja

15 Października 2024