Instrukcja obsługi Stanley STHT0-77364

Stanley multimetr STHT0-77364

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Stanley STHT0-77364 (116 stron) w kategorii multimetr. Ta instrukcja była pomocna dla 13 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/116

STHT0-77364

www.STANLEYTOOLS.com 79003408

Multimeter

FIN

2000

200k

20k

2000 200

200

20m

2000

200

2000

200

300300

User Manual

2000

200k

20k

2000 200

200

20m

2000

200

2000

200

300300

Test Leads

Highest Value

10 A

Terminal

Function/

Range

Switch

Data Hold

Button

COM

Terminal

Display

Low

Battery

Reading

K Type Thermocouple

STANLEY® Multimeter

The STANLEY Multimeter is a CAT III

300 V 10 A compact digital multimeter for

measuring DC and AC voltage, DC current,

resistance, continuity, diode polarity, and

temperature. It features polarity indication, data

hold, and overrange indication.

User Safety

WARNING: Read and understand all

instructions before using product.

Failure to follow all instructions may result in

severe injury or death:

• CAT III – This measurement Category III

multimeter is for use on permanently installed

loads. Examples are measurements on

distribution boards, circuit breakers, wiring,

and equipment like xed installation motors.

Do not use the meter for measurements

higher than Category III 300 V 10 A.

• use the meter if it is damaged. DO NOT

Before using the meter, inspect the case.

Pay particular attention to the insulation

surrounding the connectors.

• ALWAYS Inspect the test leads for damaged

insulation or exposed metal. Check the test

leads for continuity. Replace damaged test

leads before you use the meter.

• use the meter if it operates DO NOT

abnormally. Protection may be impaired.

• operate the meter where explosive DO NOT

gas, vapor, or dust is present.

• apply more than the rated voltage, DO NOT

as marked on the meter, between terminals or

between any terminal and earth ground.

• ALWAYS verify the meter’s operation by

measuring a known voltage before use.

• turn off circuit power before ALWAYS

connecting the meter in the circuit to measure

current. Remember to place the meter in

series with the circuit.

• ALWAYS turn off circuit power before

connecting the meter to the circuit to measure

resistance.

• Use caution when working with ALWAYS

voltage above 30 V AC rms, 42 V peak, or

60 V DC. These voltages pose an increased

shock hazard.

• ALWAYS keep your ngers behind the nger

guards on the probes when in use.

• ALWAYS connect the common test lead

before you connect the live test lead. When

you disconnect test leads, disconnect the live

test lead rst.

• ALWAYS Remove the test leads from the

meter before you open the battery cover or the

case.

• operate the meter with the battery DO NOT

cover or portions of the case removed or

loosened.

• ALWAYS replace the battery as soon as the

low battery indicator appears. Failure to

do so could lead to possible electric shock or

personal injury due to false readings.

• touch any conductor with hand or DO NOT

skin, and do not ground yourself.

• use the meter in a manner not DO NOT

specied by this manual or the safety

features provided by the meter may be

impaired.

• operate this instrument if your DO NOT

hand, a test lead or the instrument is wet.

• ALWAYS Adhere to local and national safety

codes. Personal protective equipment must

be used to prevent shock and arc blast

injury where hazardous live conductors are

exposed.

• be aware that when an input ALWAYS

terminal is connected to a hazardous live

voltage, this potential can occur at all other

terminals.

• ALWAYS use only 9 V batteries specied

for use with this product. Use of any other

batteries may create a risk of re.

• disassemble, service or repair this DO NOT

product. Repairs performed by unqualied

personnel could result in serious injury.

• splash or immerse the unit in water. DO NOT

• turn off the product when not in ALWAYS

use.

• ALWAYS ensure battery is inserted in the

correct manner, with the correct polarity.

• intentionally short any battery NEVER

terminals.

• attempt to charge alkaline batteries.DO NOT

• DO NOT dispose of batteries in re.

• ALWAYS remove the battery if storing the

unit for over a month.

• dispose of this product with DO NOT

household waste.

• ALWAYS check local codes and properly

dispose of used batteries.

• in line with local PLEASE RECYCLE

provisions for the collection and disposal of

electrical and electronic waste.

• WARNING: To avoid risk of personal

injury and/or possible damage to the meter

or to the equipment under test, follow these

guidelines: If these guidelines are not

followed there is risk of shock.

• Disconnect circuit power and discharge all

capacitors before testing resistance, diode,

continuity and temperature.

• Use the properly rated terminals (function

and range) for your measurements. The

terminals included with this multimeter are

CAT III rated for 300 V 10 A Max.

• Before measuring current, turn off the power

to the circuit before connecting the meter to

the circuit. Remember to place the meter in

series with the circuit.

• Before turning the rotary switch to change

functions, disconnect test leads from the

circuit under test.

Electrical Symbols

Alternating Current

Direct Current

Both direct and alternating

current

Caution, risk of danger, refer to

the operating manual before use.

Caution, risk of electric shock.

Specyfikacje produktu

Marka:	Stanley
Kategoria:	multimetr
Model:	STHT0-77364
Typ produktu:	Analogowy multimetr
Źródło zasilania:	Bateria
Typ ekranu:	LCD
Przeznaczenie:	Multimetr ręczny
Rodzaj baterii:	9V
Zakres napięcia DC:	20 - 300 V
Zakres napięcia AC:	200 - 300 V
Zakres prądu DC:	0 - 10 A
Zakres rezystancji:	0 - 30 Ω
Zakres pomiaru temperatury:	0 - 1000 °C
Kategoria pomiarowa:	CAT III 300V