Instrukcja obsługi SpinMaster AIR HOGS HAWK EYE

SpinMaster Zabawki AIR HOGS HAWK EYE

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla SpinMaster AIR HOGS HAWK EYE (1 stron) w kategorii Zabawki. Ta instrukcja była pomocna dla 2 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/1

4 1

2 3

CONTENTS LIST AND PARTS IDENTIFICATION

BECOMING FAMILIAR WITH YOUR IR CONTROLLER

IR CONTROLLER

Power Indicator

Direction Stick

(LEFT/RIGHT)

IR Emitter

Trimmer Knob

Controller

Docking Port

Power Switch

(ON/OFF)

Controller USB Port

Throttle stick

(UP/DOWN)

Problems flying?

Do not return your

Air Hogs® to the store.

Call the Air Hogs®

flight training centre

1-800-622-8339

INSTRUCTION GUIDE

Instruction GuideCustom USB Cable

AIR HOGS® HAWK EYE™

Upper Rotor Blade

Fly Bar

Connecting Shaft

Lower

Rotor Blade

WARNING:

USB cord could be a strangulation

hazard.Not for Children under 3 years.

DANGER!

NEVER INSERT ANY SHARP OBJECTS,

PINS OR SCREWS INTO THE

HELICOPTER AS THIS MAY PUNCTURE

THE INTERNAL BATTERY!

ELECTRIC TOY.

Not recommended for children under 3 years of

age. As with all electrical products, precaution

should be observed during the handling and use

to prevent electrical shock.

CAUTION:

Air Hogs

Hawk Eye™ IR Controller

Power Switch

(ON/OFF/CHG)

Camera

LED

HOW TO INSTALL YOUR BATTERIES

HOW TO CHARGE YOUR AIR HOGS® HAWK EYE™

TAKING VIDEOS OR PICTURES AFTER CHARGING

BATTERY INSTALLATION – IR CONTROLLER

1. Open the battery door with a screwdriver (pic.1). 2. If used batteries are present, remove these batteries from the unit by pulling up on one end of each

battery. 3. Install new batteries as shown in the polarity diagram (+/-) inside the battery compartment (pic.2). 4. Replace battery door securely (pic.3).

5. Check your local laws and regulations for correct recycling and/or battery disposal.

CONNECTING TO YOUR COMPUTER:

Ask your parents or legal guardian to help you with the next steps.

• Connect the larger end of the provided USB cord to your computer and the smaller end to the controller.

Ensure your computer is ON.

• Once your computer detects the Air Hogs

Hawk Eye™ it will recognize it as a drive and start charging its

battery through your computer. You will see the Air Hogs

Hawk Eye’s™ LED flashing green and

red alternatively.

• When the charge is complete, the Air Hogs

Hawk Eye’s™ LED will start flashing green only.

• To disconnect the Air Hogs

Hawk Eye™ from your computer, DO NOT simply un-plug the USB cable from your

computer and/or from the controller. Safely remove the USB drive as per your computer operating system’s

recommendation. For example, in Windows Me

, XP

, 2000

, Vista

or Windows 7

use the Safely Remove

Hardware feature; in Apple OS X™ eject the drive.

Things to remember:

1. The helicopter will have 4-5 minutes of flight time after a 35-55 minute charge.

2. Before you recharge the battery or take the next flight, wait 10-15 minutes to let the battery cool down.

• Turn on your Air Hogs® Hawk Eye™ helicopter. Turn on your controller. You are now

capable of taking videos or pictures, even before you start flying!

• To take videos, press the video button (left) once (pic.1). The Air Hogs® Hawk Eye™

LED will turn from its green standby color to a solid red indicating that video is

recording (pic.2). To stop video recording, press the video button again. The Air Hogs®

Hawk Eye™ LED will turn back to green stand-by mode.

NOTE: Do not turn off helicopter while the red light is on for video recording or else the

video cannot be saved. Be sure to stop the video recording by pressing the video button

again in order to save it.

• To take a picture, press the picture button (right) (pic.3). The Air Hogs® Hawk Eye™ will

automatically adjust focus, ISO setting and shutter speed to take your image. This

takes about 1.5 seconds, during which time the LED will turn from green to red (pic.2).

Once the LED has turned green again, you’re ready to take your next picture.

NOTE: If the picture button is pressed while a video is recording, the video is stopped

and a picture is taken. You can start the video recording again by pressing the video button.

• For best picture quality try to keep the helicopter flying straight and steady.

• Video quality is also best during straight flight. Keep turns to a minimum.

• Please respect the privacy of others. Proper consent of others and parents should be

taken before taking and/or distributing pictures and videos of other people.

• Ensure there is enough light in the room when you are taking videos or pictures. This

can affect the quality of the videos or pictures. Because of the size of the camera, it

cannot capture a lot of light in a dim room.

pic.1pic.1 pic.2pic.2

pic.1 pic.3pic.2

Turn the controller off. Turn the helicopter to

the charge position.

Carefully connect the helicopter

docking port to the controller

docking port. The front of the

helicopter is nearest to the IR

Emitter. Ensure they are properly

connected. Ensure the helicopter

docking port is free of dirt,

especially when you are not using

it. Store it carefully and avoid

getting wet. The charging

connection will be affected if the

connection is rusted or full of dirt.

STEP ONE STEP TWO STEP THREE STEP FOUR

3. FLIGHT CONTROL (After Trimming)

Hover up and down:

When the helicopter flies steadily, you can slowly push the throttle stick up

to make the helicopter fly higher, or release the stick a bit to make the

helicopter fly lower. Only small amounts of stick position change are required

for smooth flying (pic.4 & pic.5).

Turn counterclockwise and clockwise:

Hold the helicopter at a height. Push the direction stick toward the left to

turn counterclockwise (pic.6), or push the direction stick toward the right

to turn clockwise (pic.7). Only a small amount of direction stick change is

required for turns.

Flying forward:

The helicopter will fly forward automatically to record your video and will accelerate when given a slight amount of throttle.

NOTE: Hovering is half the

battle. If you can maintain your

helicopter in a stable position

in the air you are on your way

to becoming a PRO.

• Put the helicopter on a smooth surface. Uneven floor surface will affect its lifting off.

• Slowly increase the throttle. NOTE: Once the helicopter leaves the ground it automatically flies forward slowly.

• DO NOT look at the controller but focus on the helicopter.

• As soon as the helicopter leaves the ground, reduce throttle slightly (in the worst case scenerio, the helicopter will drop back

to the floor, but that is better than crashing against the ceiling).

• VERY gently add throttle if the helicopter goes down.

• VERY gently reduce throttle if helicopter goes up.

• For turning, give short and small inputs to the direction stick (most beginners will easily over control the helicopter).

pic.4

Hover up

pic.5

Hover down

pic.6 pic.7

HOW TO FLY YOUR AIR HOGS® HAWK EYE™

LED INDICATIONS

1. TRIMMING YOUR HELICOPTER:

2. FLYING INDOORS

Gently push the throttle up to raise your helicopter 1.5 ft. to 3.25 ft. high off the ground.

If your helicopter turns CLOCKWISE, continue to turn the trim to the left until the turning stops

and the helicopter flies straight.

If your helicopter turns COUNTERCLOCKWISE, continue to turn the trim button to the right until the turning stops

and the helicopter flies straight.

Keep turning clockwise

Spiral clockwise

Keep turning counterclockwise

Spiral counterclockwise

STEP

ONE

STEP

TWO

STEP

THREE

Location – Fly in a wide-open room [ideally over 10 ft. (W) x 16.5 ft. (L) x 8 ft. (H)], away from breakable items. Avoid flying near vents and/or fans, as these may

overpower the Air Hogs

Hawk Eye™ and make it difficult to control. NOTE: Always get permission to fly your Air Hogs

Hawk Eye™ indoors.

CAUTION: Never fly near your face. Keep propeller away from your fingers, hair, eyes and other body parts. Always lift from a flat surface. Never hold the

flying toy in your hand when lifting off. Do not launch flying toy at people or animals.

WARNING: If rotor(s) become damaged or broken, do not fly. Flying with broken rotor(s)

may cause damage or lead to injury.

Air Hogs® Hawk Eye™ Helicopter:

• Off – LED off

• On – LED solid green

• Video recording mode – LED solid red

• Picture recording mode – LED red for approximately 1.5 seconds

• Charging mode on controller – LED flashing alternatively between

red and green

• Full charge reached – LED flashing green

• Low Air Hogs

Hawk Eye™ battery – LED solid orange

• Memory full – LED flashing orange

IR Controller:

• Off/Download/Charging mode – LED off

• On – LED solid green

• Low controller battery – LED flashing green

TROUBLESHOOTING

Main rotor won’t move.

Suddenly stops and drops while flying.

Helicopter is not reacting to the controller.

Helicopter is losing control.

Helicopter is not holding a charge.

Helicopter will not lift off the ground.

Helicopter only turns in one direction.

Video is not being recorded.

Picture is not being taken.

Helicopter is not charging.

Videos/pictures are blurry.

PROBLEM

ON/OFF switch is set to OFF.

Weak battery.

Weak power.

Helicopter may be out of range from controller.

Helicopter or controller may not be turned ON.

May be another infrared (IR) device using the same

channel.

Bright lights may be affecting the IR control.

You may be too far away from the controller.

Helicopter might be turned ON while charging.

Controller is low on battery power.

Helicopter may not be fully charged.

Helicopter is not trimmed correctly.

NOTE: Helicopter only moves forward and sideways.

Memory is full. Air Hogs® Hawk Eye™ helicopter LED

is flashing orange.

Video and picture buttons were pressed at the

same time.

The helicopter is turned off or is not fully charged

during the video recording period, so the video clip

cannot be saved.

Memory is full. Air Hogs® Hawk Eye™ helicopter LED

is flashing orange.

Picture button is being repeatedly pressed too fast.

Computer is not turned on.

The helicopter or USB is not properly connected.

Video/picture viewing software set to higher than

100% zoom.

Pictures are being taken while the helicopter is

turning/spinning.

CAUSE

Set switch to ON.

Re-charge the helicopter using the charging port OR check batteries in the controller.

Re-charge helicopter or check battery power in controller.

Move closer to the helicopter with the controller or fly heli higher than controller.

Turn helicopter and/or controller ON.

Avoid these if possible, or choose another place to operate the helicopter.

Avoid flying near windows or bright lights or choose another place to operate the

helicopter.

Move closer to the helicopter with the controller.

Turn OFF the helicopter so that it is not flashing.

Replace batteries in the controller.

Charge helicopter fully, until green light starts flashing.

Refer to the TRIMMING section in the instruction sheet.

Ensure the memory in the Air Hogs® Hawk Eye™ is free. Refer to “Accessing your

video(s) and picture(s)”.

Press only the video button.

Make sure to stop video recording by pressing the video button. Do not turn

off the helicopter directly during video recording or the video clip cannot be saved

into memory.

Ensure the memory in the Air Hogs Hawk Eye is free. Refer to “Accessing your

video(s) and picture(s)”.

Wait approximately 1.5 seconds or until the Air Hogs® Hawk Eye™ LED turns back

green before taking the next picture.

Ensure your computer is turned on. If on, try a different USB port on your computer.

Ensure the helicopter is properly docked on the controller and the USB cord is well

connected to the controller and computer.

Consult your video/picture viewing software manual or online help section to

ensure you are viewing the pictures/videos at 100% zoom. The resolution of the

pictures/videos is QVGA (320 x 240 pixels).

Ensure your helicopter is properly trimmed. Try taking pictures when the helicopter is

flying straight.

SOLUTION

Spin Master Ltd., 450 Front Street West, Toronto, ON M5V 1B6 Canada

Spin Master Inc., PMB #10053, 300 International Drive, Suite 100,

Williamsville, NY 14221, USA

Spin Master Toys Far East Limited. Rm #1113, 11/F,

Chinachem Golden Plaza, 77 Mody Rd., Tsimshatsui E., Kowloon, HK

North American Consumer Information

Phone: 1-800-622-8339

Email: customercare@spinmaster.com

customercare@spinmaster.com

product conforms to safety requirements of ASTM F963. • Please retain this information

for future reference. • Please remove all packaging materials before giving to children.

• An adult should periodically check this toy to ensure no damage or hazards exist, if so,

remove from use. • Children should be supervised during play. • Keep addresses and

phone numbers for future reference. • The item inside this package may vary from the

photographs and/or illustrations. Patent Pending. MADE IN CHINA.

20027740, 20027741 REV 2

T44382_0001_20027740_IS_NEN_R3

For further questions and problems, please visit our website www.airhogs.com.

Battery requirement for Controller:

Power Supply :

Rating : DC 4.5 V, 0.45 W

Requires 3 x 1.5 V "AAA" size batteries (not included)

Battery requirement for Air Hogs

Hawk Eye™:

Power Supply :

USB Rating : Input/Output rating: DC 5V, 1A

Batteries : 1 x 3.7 V Li-Poly Rechargeable Battery Pack

Requires 1 x 3.7 V Li-Poly Rechargeable Battery Pack (included)

BATTERY SAFETY INFORMATION:

- Requires 3 x 1.5-V AAA alkaline batteries (not

included).

- Batteries are small objects.

- Replacement of batteries must be done by adults.

- Follow the polarity (+/-) diagram in the battery

compartment.

- Promptly remove dead batteries from the toy.

- Dispose of used batteries properly.

- Remove batteries for prolonged storage.

- DO NOT incinerate used batteries.

- DO NOT dispose of batteries in fire, as batteries may

explode or leak.

- DO NOT mix old and new batteries or types of

batteries (i.e. alkaline/standard).

- DO NOT use rechargeable batteries.

- DO NOT recharge non-rechargeable batteries.

- DO NOT short-circuit the supply terminals.

Care and Maintenance:

- Always remove batteries from the toy when it is not

being used for a long period of time (controller only).

- Wipe the toy gently with a clean damp cloth.

- Keep the toy away from direct heat.

- Do not submerge the toy in water. This can damage

the electronic assemblies.

- Always helicopter and controller in a box away from

dirt and humidity when not being used.

Special Note to Adults:

- Regularly examine for damage to the plug, enclosure and other parts. In the event of any

damage, the toy must not be used with the controller until the damage has been repaired.

- This toy is not intended for children under 3 years old.

- This toy must only be used with the recommended controller.

- Do not try to charge other batteries with the controller.

Safety Precautions:

- Keep hands, hair and loose clothing away from the rotors when power switch is turned ON.

- Turn off controller and helicopter when not in use

- Remove battery from controller when not in use.

- Parental guidance is recommended for the flight.

- Keep your helicopter in your sight so that you can supervise it all the time.

- New alkaline batteries are recommended for use in controller to obtain maximum performance.

- Users should keep strict accordance with the instruction manual while operating the product.

- Your controller is tailor-made for the Li-Poly rechargeable battery used in your Air Hog

Hawk Eye™.

Do not use it to charge any battery other than that in the helicopter.

This product complies with Part 15 of the FCC rules. Operation is subject to the following two

conditions: (1) This device may not cause harmful interference, and (2) This device must accept any

interference received, including interference that may cause undesirable operation. This equipment has been

tested and found to comply with the limits for Class B digital devices pursuant to Part 15 of the FCC rules.

These limits are designed to provide reasonable protection against harmful interference to radio

communications. Because this toy generates, uses, and can radiate radio frequency energy, there can be no

guarantee that interference will not occur. If this toy does cause interference to radio or television reception

(you can check this by turning the toy off and on while listening for the interference), one or more of the

following measures may be useful: • Reorient or relocate the receiving antenna • Increase the separation

between the toy and the radio or the TV • Consult the dealer or an experienced TV-radio technician for help.

NOTE: Changes, adjustments or modifications to this unit, including but not limited to, replacement of any

transmitter component (crystal, semiconductor, etc.) could result in a violation of FCC rules under part 15

and/or 95 and must be expressly approved by Spin Master Ltd. or they could void the user’s authority to

operate the equipment.

Your Air Hogs

Hawk Eye™ is equipped with a

Lithium Polymer battery.

SPECIAL LiPO BATTERY INSTRUCTIONS:

- Never charge battery unattended.

- Charge battery in isolated area. Keep away from

flammable materials.

- Do not expose to direct sunlight. There is a risk of the

batteries exploding, overheating, or igniting.

- Do not disassemble, modify heat, or short circuit the

batteries. Do not place them in fires or leave them in hot

places.

- Do not drop or subject to strong impacts.

- Do not allow the batteries or connectors to get wet.

- Only charge the batteries with the specified Spin

Master™ battery charger.

- Only use the batteries in the device specified by

Spin Master™.

- Only use the USB cable specified by Spin Master™.

Only use the cable which is provided with this

product.

- Carefully read the instruction guide and use the

batteries correctly.

- In the unlikely event of leakage or explosion use sand

or a chemical fire extinguisher for the battery.

- Batteries must be recycled or disposed of properly.

NOTE: If normal function of the product is disturbed or interrupted, strong electro-magnetic

interference may be causing the issue. To reset product, turn it completely off, then turn it

back on. If normal operation does not resume, move the product to another location and try

again. To ensure normal performance, change the batteries, as low batteries may not

allow full function.

ACCESSING YOUR VIDEO(S) AND/OR PICTURE(S)

Picture Capture

Button

Video Capture

Button

Minimum Throttle position

pic.3pic.3

Helicopter

Docking Port

Connect the small end of the

provided USB cord to the

small USB port located at the

bottom of the controller.

VIDEO CAMERA HELICOPTER

Note: - Parental guidance is recommended when

installing or replacing batteries.

- In an environment with electrostatic discharge, the

toy may malfunction. This requires the user to reset

the toy by unplugging then re-plugging the USB

Cable.

EXPERT

YRS

• With parental supervision, follow the steps for charging your

Air Hogs

Hawk Eye™ until your computer recognizes your Air Hogs

Hawk Eye™ as a drive.

NOTE: You can charge and access your picture and video files at the

same time.

• Once your computer detects the Air Hogs

Hawk Eye™ as a drive you

can access this drive to copy the picture(s) and/or video(s) you have

taken. The files will be in standard JPEG format for the pictures and

standard AVI format for videos. You can view the pictures in this drive

using your preferred software.

• If you wish to save your pictures to your computer, you can copy the

files to your computer. Afterwards, to free up memory space on your

Air Hogs

Hawk Eye™ for your next mission, you will have to remove the

files that are on the Air Hogs

Hawk Eye™ by transferring the files to

your computer.

• Once you have finished accessing your picture(s) and/or video(s) and the

Air Hogs

Hawk Eye™ is fully charged you may disconnect the Air Hogs

Hawk Eye™ as per the charging instructions.

• Please note that the Air Hogs

Hawk Eye™ does not record sound.

CAUTION: It is rare but possible for a seizure to be triggered by

light flashes or patterns such as those on the computer screen. To reduce

exposure to this potential hazard, sit in a well-lit room, sit an appropriate

distance from the screen and take 10 to 15 minute breaks every hour.

PRODUCT BATTERY REMOVAL INSTRUCTIONS:

Internal battery is factory installed, product disassembly and battery removal must be

performed by an adult. Do not use any tools for disassembly. Pulling, tearing, and deforming

of the product during disassembly, while necessary, should be as limited as possible. Do not

compress the product at any time. Ensure product is turned off. Find a point where the two

body halves meet; the nose of the aircraft or where the wing meets the body. Start to peel the

halves apart, separating them where they are glued together; remove any tape as necessary.

Separate product body halves to expose internal electronics. To separate battery from product

use scissors to cut a single battery wire, immediately wrap the cut wire end with tape to

isolate it, repeat until all battery wires are cut and isolated. Dispose of battery in accordance

with your local battery recycling or disposal laws. NOTE: Opening of product and/or removal

of battery will render product inoperative and voids manufacturer warranties, dispose of

remaining product components in accordance with local laws.

DOWNLOAD FREE

EDITING SOFTWARE!

Easily add cool images,

sounds and words to

your videos and pictures

and share them with

your friends.

Visit

www.airhogs.com

to register and access

the software.

DOWNLOAD FREE

EDITING SOFTWARE!

Easily add cool images,

sounds and words to

your videos and pictures

and share them with

your friends.

Visit

www.airhogs.com

to register and access

the software.

Specyfikacje produktu

Marka:	SpinMaster
Kategoria:	Zabawki
Model:	AIR HOGS HAWK EYE

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z SpinMaster AIR HOGS HAWK EYE, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą

Twoje imię*

Twój email*

Napisz tutaj swoje pytanie

Instrukcje Zabawki SpinMaster

SpinMaster Air Hogs Axis 300x Instrukcja

26 Września 2024

SpinMaster Zoomer Zuppies - Scarlet Instrukcja

26 Września 2024

SpinMaster Pottery Cool Studio Instrukcja

26 Września 2024

SpinMaster Meccano - Meccanoid 2.0. Instrukcja

25 Września 2024

SpinMaster Cool Maker - Tidy Dye Station Instrukcja

25 Września 2024

SpinMaster The Castle Escape Challenge - Rube Goldberg Instrukcja

25 Września 2024

SpinMaster Refill Hip Holders Instrukcja

25 Września 2024

SpinMaster Knits Cool Studio Instrukcja

25 Września 2024

SpinMaster BATTLE TRACKER - Air Hogs Instrukcja

25 Września 2024

SpinMaster Meccano - Micronoid Code Magna Instrukcja

25 Września 2024

Instrukcje Zabawki

Najnowsze instrukcje dla Zabawki

Lego Raceway Rider Instrukcja

13 Października 2024

Lego Dora Club Co-Pack Instrukcja

13 Października 2024

Lego Puppy Playground Instrukcja

11 Października 2024

Lego Value Pack Star Wars Instrukcja

10 Października 2024

Ikea DUKTIG 505.892.24 Instrukcja

9 Października 2024

Ikea SKOGSDUVA 805.786.72 Instrukcja

9 Października 2024

Hasbro Furby Instrukcja

9 Października 2024

Kogan KARDONFRENA Instrukcja

9 Października 2024

Mega Bloks Despicable Me - Micro Action Figures Series 10 Instrukcja

9 Października 2024

Mega Bloks Buildable Minions Blind Packs Series III Instrukcja

9 Października 2024