Instrukcja obsługi Speco Technologies O4T7MN

Speco Technologies Kamera monitorująca O4T7MN

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Speco Technologies O4T7MN (57 stron) w kategorii Kamera monitorująca. Ta instrukcja była pomocna dla 7 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/57
User Manual
4MP IP Camera
O4 /O4B6/O4B7M/O4D6/O4D7M/O4T7/O4T7M P4
Please read this instrucon carefully before operang the unit keep it for further reference and
Important Safeguards and Warnings
1. Electrical safety
All installaon and operaon here should conform to local electrical safety codes.
Use a certied/listed 12VDC Class2 power supply only.
Please note: Do not connect two power supplying sources to the device at the same me; it may result in device damage! The
product must be grounded to reduce the risk of electric shock.
Improper handling and/or installaon could run the risk of re or electrical shock.
2. Environment
Heavy stress, violent vibraon or exposure to water is not allowed during transportaon, storage and installaon.
This product should be installed in a cool, dry place away from direct sunlight and heat sources.
Do not install the product in extreme temperature condions.
Do not expose the camera to electromagnec radiaon. Otherwise it may result in CMOS sensor failure.
Do not block any venlaon openings.
Do not allow water and liquid intrusion into the camera.
3. Operaon and Daily Maintenance
Please shut down the device and then unplug the power cable before you begin any maintenance work.
Do not touch the CMOS sensor opc component. You can use a blower to clean the dust on the lens surface.
Always use the dry so cloth to clean the device. If there is too much dust, use a cloth dampened with a small quanty of neutral
detergent. Finally use the dry cloth to clean the device.
Please use a professional opcal cleaning method to clean the enclosure. Improper enclosure cleaning (such as using cloth) may
result in poor IR functionality and/or IR reecon.
The grounding holes of the product are recommended to be grounded to further enhance the reliability of the camera.
Dome cover is an opcal device, please don t touch or wipe cover surface directly during installaon and use, please refer to the ’
following methods if dirt is found.
Stained with dirt:
Use oil-free so brush or hair dryer to remove it gently.
Stained with grease or ngerprint
Use oil-free cotton cloth or paper soaked with alcohol or detergent to wipe from the lens center outward. Change the cloth and
wipe several mes if it is not clean enough.
Warning
This camera should be installed by qualied personnel only.
All the examinaon and repair work should be done by qualied personnel.
Any unauthorized changes or modicaons could void the warranty.
Statement
This guide is for reference only.
Product, manuals and specications may be modied without prior noce. Speco Technologies reserves the right to modify these
without noce and without incurring any obligaon.
Speco Technologies is not liable for any loss caused by improper operaon.
Regulatory Informaon
FCC condions:
This device complies with part 15 of the FCC Rules. Operaon is subject to the following two condions:
This device may not cause harmful interference.
This device must accept any interference received, including interference that may cause undesired operaon.
FCC compliance:
This equipment has been tested and found to comply with the limits for a digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protecon against harmful interference. This equipment generates uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instrucon manual, may cause harmful
interference to radio communication. However, there is no guarantee that interference will not occur in a parcular installaon. If
this equipment does cause harmful interference to radio or television recepon, which can be determined by turning the
equipment o and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separaon between the equipment and receiver.
Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.
Note:
Before installaon, check the package and make sure that all components are included.
Contact your rep or Speco customer service department immediately if something is broken or missing in the package.
Accessory name
Amount
Network Camera Unit
1
Juncon box (Wall mount for O4P4)
1
Quick Start Guide
1
Installaon Accessories Bag
1
CD
1

Specyfikacje produktu

Marka: Speco Technologies
Kategoria: Kamera monitorująca
Model: O4T7MN

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Speco Technologies O4T7MN, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje Kamera monitorująca Speco Technologies

Speco Technologies

Speco Technologies VLDT3GM Instrukcja

22 Września 2024
Speco Technologies

Speco Technologies CVC624WDR Instrukcja

20 Września 2024
Speco Technologies

Speco Technologies O4iB2M Instrukcja

20 Września 2024
Speco Technologies

Speco Technologies ZIPTW4B1 Instrukcja

18 Września 2024
Speco Technologies

Speco Technologies O2ID21M Instrukcja

18 Września 2024
Speco Technologies

Speco Technologies Intensifier 2 CVC6246iHR Instrukcja

18 Września 2024
Speco Technologies

Speco Technologies O4DT1 Instrukcja

18 Września 2024
Speco Technologies

Speco Technologies O4iB2 Instrukcja

18 Września 2024
Speco Technologies

Speco Technologies O8D8M Instrukcja

17 Września 2024
Speco Technologies

Speco Technologies CVC5100BPVFW Instrukcja

17 Września 2024

Instrukcje Kamera monitorująca

Najnowsze instrukcje dla Kamera monitorująca

Trebs

Trebs CCD-401C Instrukcja

15 Października 2024
Hikvision

Hikvision DS-2CE56D5T-AIRZ Instrukcja

15 Października 2024
D-Link

D-Link DCS-7510 Instrukcja

15 Października 2024
Ubiquiti Networks

Ubiquiti Networks UniFi Video UVC-G3-AF Instrukcja

14 Października 2024
Hikvision

Hikvision DS-2TD2137-7/VP Instrukcja

13 Października 2024
Alecto

Alecto DVC-215IP Instrukcja

13 Października 2024
Hikvision

Hikvision DS-2DE7A245IX-AE/S1 Instrukcja

13 Października 2024
Hikvision

Hikvision DS-2TD2166-15/V1 Instrukcja

13 Października 2024
Hikvision

Hikvision DS-2CD2325FWD-I Instrukcja

13 Października 2024
Hikvision

Hikvision DS-2CD2323G2-IU Instrukcja

12 Października 2024