Instrukcja obsługi Speco Technologies O4DT1
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Speco Technologies O4DT1 (11 stron) w kategorii Kamera monitorująca. Ta instrukcja była pomocna dla 15 osób i została oceniona przez 8 użytkowników na średnio 4.9 gwiazdek
Strona 1/11

Quick Start Guide
4MP Turret IP Camera
O4DT1
Version 1.0.0

i
Welcome
Thank you for purchasing this network camera!
This manual is designed to be a reference guide for the product .
Please read this manual carefully before operang the unit and retain it for future reference.
Should you require any technical assistance, please contact Speco Technologies Technical Support.

ii
Important Safeguards and Warnings
1 Electrical safety
.
.
.
..
All installaon and operaon here should conform to local electrical safety codes.
Use a cered/listed 12VDC Class 2 power supply only.
Please note: Do not connect two power supplying sources to the device at the same me; it may
result in device damage! The product must be grounded to reduce the risk of electric shock.
Improper handling and/or installaon could run the risk of re or electrical shock.
2 Environment
.
.
.
..
Heavy stress, violent vibraon or exposure to water is not allowed during transportaon, storage
and installaon.
This product should be installed in a cool, dry place away from direct sunlight and heat sources.
Do not install the product in extreme temperature condions.
Do not expose the camera to electromagnec radiaon. Otherwise it may result in CMOS sensor
failure.
Do not block any venlaon openings.
Do not allow water and liquid intrusion into the camera.
3. Operaon and Daily Maintenance
Please shut down the device and then unplug the power cable before you begin any maintenance
work.
Do not touch the CMOS sensor opc component. You can use a blower to clean the dust on the
lens surface.
Always use the dry so cloth to clean the device. If there is too much dust, use a cloth dampened
with a small quanty of neutral detergent. Finally use the dry cloth to clean the device.
Please use a professional opcal cleaning method to clean the enclosure. Improper enclosure
cleaning (such as using cloth) may result in poor IR funconality and/or IR reecon.
The grounding holes of the product are recommended to be grounded to further enhance the
reliability of the camera.
Dome cover is an opcal device, please don’t touch or wipe cover surface directly during
installaon and use, please refer to the following methods if dirt is found:
Stained with dirt
Use oil-free so brush or hair dryer to remove it gently.
Stained with grease or ngerprint
Use oil-free coon cloth or paper soaked with alcohol or detergent to wipe from the lens center
outward. Change the cloth and wipe several mes if it is not clean enough.
Specyfikacje produktu
Marka: | Speco Technologies |
Kategoria: | Kamera monitorująca |
Model: | O4DT1 |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z Speco Technologies O4DT1, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje Kamera monitorująca Speco Technologies
12 Stycznia 2025
12 Stycznia 2025
11 Stycznia 2025
22 Września 2024
20 Września 2024
20 Września 2024
18 Września 2024
18 Września 2024
18 Września 2024
18 Września 2024
Instrukcje Kamera monitorująca
- Kamera monitorująca Vtech
- Kamera monitorująca Control4
- Kamera monitorująca IPX
- Kamera monitorująca AVMATRIX
- Kamera monitorująca Furrion
- Kamera monitorująca Netis
- Kamera monitorująca AVer
- Kamera monitorująca Nest
- Kamera monitorująca Vimtag
- Kamera monitorująca Insteon
- Kamera monitorująca Ubiquiti Networks
- Kamera monitorująca Netgear
- Kamera monitorująca Grundig
- Kamera monitorująca Allnet
- Kamera monitorująca INSTAR
Najnowsze instrukcje dla Kamera monitorująca
28 Stycznia 2025
25 Stycznia 2025
17 Stycznia 2025
17 Stycznia 2025
15 Stycznia 2025
13 Stycznia 2025
13 Stycznia 2025
13 Stycznia 2025
12 Stycznia 2025
12 Stycznia 2025