Instrukcja obsługi Speco Technologies O2TML

Speco Technologies termometr O2TML

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Speco Technologies O2TML (64 stron) w kategorii termometr. Ta instrukcja była pomocna dla 6 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/64
Please read this manual carefully before operating the unit and keep it for fu reference ture .
O2TML
Temperatur g Panel with e Readin
Face and Mask Recognition
User Manual
v1.0
Important Safeguards and Warnings
1. Electrical safety
All installation and operation here should conform to local electrical safety codes.
Use a certified/listed 12VDC 1A or more Class2 power supply only.
Please note: Do not connect two power supplying sources to the device at the same time; it
may result in device damage! The product must be grounded to reduce the risk of electric
shock.
Improper handling and/or installation could run the risk of fire or electrical shock.
2. Environment
Heavy stress, violent vibration or exposure to water is not allowed during transportation,
storage and installation.
This product should be installed in a cool, dry place away from direct sunlight and heat
sources.
Do not install the product in extreme temperature conditions.
Do not expose the camera to electromagnetic radiation. Otherwise it may result in CMOS
sensor failure. Do not block any ventilation openings.
Do not allow water and liquid intrusion into the camera.
3. Operation and Daily Maintenance
Do not attempt to disassemble the camera; in order to prevent electric shock, do not remove
screws or covers.
There are no user-serviceable parts inside. Please contact the nearest service center as soon as
possible if there is any failure.
Avoid from incorrect operation, shock vibration, heavy pressing which can cause damage to
product.
Do not use corrosive detergent to clean main body of the camera. If necessary, please use soft
dry cloth to wipe dirt; for hard contamination, use neutral detergent. Any cleanser for high
grade furniture is applicable.
Avoid aiming the camera directly towards extremely bright objects, such as, sun, as this may
damage the image sensor.
Please follow the instructions to install the camera. Do not reverse the camera, or the reversing
image will be received.
Do not operate it in case temperature, humidity and power supply are beyond the limited
stipulations. Keep away from heat sources such as radiators, heat registers, stove, etc.
Do not expose the product to the direct airflow from an air conditioner.
This manual is for using and managing the product. We may reserve the rights of amending the
typographical errors, inconsistencies with the latest version, software upgrades and product
improvements, interpretation and modification. These changes will be published in the latest
version without special notification.
All pictures, charts, images in this manual are only for description and explanation of our
products. The ownerships of trademarks, logos and other intellectual properties related to
Microsoft, Apple and Google belong to the above-mentioned companies.
Temperature Reading Panel Face with and Mask Recognition
Warning
This camera should be installed by qualified personnel only.
All the examination and repair work should be done by qualified personnel.
Any unauthorized changes or modifications could void the warranty.
Statement
This guide is for reference only.
Product, manuals and specifications may be modified without prior notice. Speco
Technologies reserves the right to modify these without notice and without incurring any
obligation.
Speco Technologies is not liable for any loss caused by improper operation.
Regulatory Information
FCC conditions:
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions:
This device may not cause harmful interference.
This device must accept any interference received, including interference that may cause
undesired operation.
FCC compliance:
This equipment has been tested and found to comply with the limits for a digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference. This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instruction manual, may
cause harmful interference to radio communication. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more
of the following measures:
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment and receiver.
•Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
Note:
Before installation, check the package and make sure that all components are included.
Contact your rep or Speco customer service department immediately if something is broken or
missing in the package.
This device is not intended for use in the diagnosis of any disease or other conditions or in
the cure, mitigation, treatment, or prevention of any disease.

Specyfikacje produktu

Marka: Speco Technologies
Kategoria: termometr
Model: O2TML

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Speco Technologies O2TML, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje termometr Speco Technologies

Speco Technologies

Speco Technologies O2TML Instrukcja

6 Września 2024

Instrukcje termometr

Najnowsze instrukcje dla termometr

Tefal

Tefal TD1400 Instrukcja

15 Stycznia 2025
AGM

AGM Taipan TM15-256 Instrukcja

15 Stycznia 2025
AGM

AGM Fuzion LRF TM35-384 Instrukcja

15 Stycznia 2025
AGM

AGM Taipan TM15-384 Instrukcja

15 Stycznia 2025
AGM

AGM Explorator FSB50-640 Instrukcja

15 Stycznia 2025
AGM

AGM Fuzion LRF TM50-640 Instrukcja

15 Stycznia 2025
AGM

AGM Fuzion LRF TM25-384 Instrukcja

15 Stycznia 2025
AGM

AGM F14 Instrukcja

15 Stycznia 2025
AGM

AGM ASP TM25-640 Instrukcja

14 Stycznia 2025
AGM

AGM ASP TM35-384 Instrukcja

14 Stycznia 2025