Instrukcja obsługi Speco Technologies HLED31D7W

Speco Technologies Kamera monitorująca HLED31D7W

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Speco Technologies HLED31D7W (2 stron) w kategorii Kamera monitorująca. Ta instrukcja była pomocna dla 2 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/2
◈NOTES:
1. Do not install the camera outdoors.
2. Choose a location for the camera which is free o
f
moisture and vibration.
3. Be careful not to scratch the camera lens or dome
cover.
4. Do not operate camera beyond listed temperature
(-49°F~122°F)
5. Handle with care. Dropping it can cause serious
damage to the camera.
6. Avoid any direct sun light into the lens.
7. To avoid shorting or damaging the camera, use
only power supplies which meet the listed
specifications (12VDC / 24VAC Dual voltage, 1A)
◈FEATURE
1. 650 TVL High Resolution Image
2. Smart DNR technology; reduces noise in low light.
3. 75’ range visible in total darkness with 24pcs of IR
LEDs. (Indoor).
4. T his camera is flexible to install with its 3-axis
camera construction, this allows for the camera to
be mounted to ceiling, wall or slope surfaces.
5. True Day/Night, camera changes function based
on illumination, IR illuminators in dark (option)
6. 8 individual privacy zones
7. DWDR (Digital Wide Dynamic Range)
8. Multi function: High Light Mask, Lens Shading
Compensation, Smart Motion Detection
9. Smart IR: Objects can be clearly identified due to
the function that decreases screen saturation o
f
objects within a short distance when the IRs are
active.
10. Multi-language OSD.
11. 12VDC / 24VAC Dual Voltage operation.
◈HOW TO INSTALL
1. Opening the dome
Push in the latch button and pull back dome.
(Remove the protection sheet after installation is
completed).
2. Removing t he dome
Lift the dome. W hen you push the latch button, it is
unlocked and you can lift the dome.
3. Camera installation
a. Mount the camera set with the supplied screws on
ceiling or wall.
It is recommended to utilize the supplied screws.
<Ceiling mount>
<Wall mount>
b. Please refer to Section 4 for details on Camera angl
e
adjustments
c. Lens adjustment (Vari-focal Lens only)
After opening the LED cover,
① By turning the “Tele-
Wide” knob, you ca
n
access a range of foca
lengths within specifie
d
limits.
②Once the focal length i
s
determined, turn the
“Near-Far” knob to se
t
the focus for the desire
scene.
d. Re-assemble the camera.
4. Camera angle adjustment
a. Pan adjustment: Turn the disk of camera and the
n
adjust direction to the right or left (-180˚ to 180˚)
b. Tilt adjustment: Turn the camera holder (shown
below) to adjust the direction up or down (6 to˚
90˚)
c. R oll adjustment: Rotate the camera holder (-178˚
to 178 ) ˚
<Caution> If the camera is adjusted beyond the
angle limit, it may cause damage to the camera.
◈ASSEMBLY
◈DIMENSION
◈SPECIFICATION
Model N o. HLED3 1D7B
HLED3 1D7W
HLED3 1D1B
HLED3 1D1W
Image S ensor 1/3" COLOR SONY SUPER HAD CCD II
Effective Pixel 768(H) x 49 4(V ) Pixel
Cell S ize 6.35
㎛
(H) x 7.4
㎛
(V )
Scanning S ystem 2 : 1 Interlace
Sync. Type Internal
R esol ution 650 TV -Line
S/N 52dB or More(A GC O FF)
V ideo O utput 1.0 V p-p(S ync. Negative) Termi nation 75 Ω
Min. Illumination 0.01L ux(F/1.2)
0Lux (75’ R ange with 24pcs LED) - Indoor
Ga mma γ = 0.45 typ.(0.2 ~ 1.0)
OS D Yes(M ulti Lan guage)
White Balance AT W(2,50 0°K ~ 9,500°K )/MA NU A L/A W C
Shutter Speed 1/60 ~ 1/100,000sec
Sense up Auto(Selectable limit 2X~1024X )/FIXE D/OFF
Backlight OF F/BLC /HLC/DWDR
A GC LO W /MIDD LE /HI GH/OF F
DN R (3D) A UTO/LOW/MI DD LE /HIGH/O FF
Motion Detection ON /OF F(4 Zone)
Privacy Zone ON /OF F(8 Zone)
Mirror ON /OF F
Day & N ight A UTO, COLOR , B/W
LE D Brightness 24pcs, Sm art IR
Blemish
Compe nsation A UTO/OFF
Lens f = 3.6mm f = 2.8 ~ 12m m
Power S upply 12V DC / 24 VAC D ual V oltage
Current Consumption Max. 600mA (at 12V D C / 24VA C)
Operation Temp. -49°F~122°F
Dimension Ø130.8(W ) x 96(H) mm
Weight 14.5 oz
※The specification is subject to change without any prior
notice to improve the quality.
◈FUNCTION SETTING
1. How to use the jog lever
①SET : Used to access the menu and confirm
selection.
②UP, DOWN :③ Used to move the cursor to up or
down.
④LEFT, RIGHT :⑤ Used to move the cursor to left
or right and change the value.
⑥EXT-VIDEO : Additional video output terminal for
test monitor during installation.
⑦DEBUG PORT : It is used for upgrading the product
function and after-sales services.
HLED31D1B, HLED31D1W
HLED31D7B, HLED31D7W
ROTATION
U
D
R
L
LED COVER
DISK
CAMERA
HOLDER
DOME COVER ASS’Y
CAMERA
MODULE ASS’Y
SCREW
HARNESS
LED COVER
ASS’Y
SCREW
CONTROL PCB ASS’Y
PUSH BUTTON
DISK
BASE CABLE
Ø109
48.1
101
Ø130.8
Ø100
Protection sheet
LATCH BUTTON
SCREW TP1
3.5X20 2EA
SCREW TP1
3.5X20 2EA
2
. OSD Menu Structure
OSD Menu
Select Menu
Sub Menu Summary
1. EXPOSURE
LENS
MANUAL
BRIGHTNESS
0~99 : Adjust brightness with a manual iris lens
E. SHUTTER
AUTO, 1/60, 1/100FLK, 1/120, 1/250, 1/500,
1/1000, 1/2000, 1/4000, 1/10000, 1/100000
: Adjust shutter speed
DC
BRIGHTNESS
0~99 : Adjust brightness with a DC iris lens
E. SHUTTER
AUTO, 1/60, 1/100FLK, 1/120, 1/250, 1/500,
1/1000, 1/2000, 1/4000, 1/10000, 1/100000
: Adjust shutter speed
AGC OFF, LOW, MIDDLE, HIGH
Determines that use the AGC function or not
and AGC level selectable(You can not use the
Auto D&N change mode when AGC is off)
SENSE-UP
AUTO, OFF, X2, X4, X8, X16,
X32, X64,X128, X256, X512,
X1024
Using sense up when it is low luminance
(x2~x1024)
BACKLIGHT
BLC
BLC LEVEL OFF, LOW, MID, HIGH : Use BLC function or
not / level selectable
TOP 0~15 : Adjust top position of BLC zone
BOTTOM 1~16 : Adjust bottom position of BLC zone
LEFT 0~15 : Adjust left position of BLC zone
RIGHT 1~16 : Adjust right position of BLC zone
HLC
HBLC
OFF : Deactivates HBLC function
MANUAL
HBLC LEVEL : OFF, LOW, MID, HIGH
TOP : 0~15
Make a zone for HBLC
BOTTOM : 1~16
LEFT : 0~15
RIGHT : 1~16
MODE ALL DAY : Activates HBLC function all day
NIGHT : Use the function at night only
HLC LEVEL 1~100 : Level adjust
MASK 1~4
ON
TOP : 0~33
Make a zone for HLC mask
BOTTOM : 1~34
LEFT : 0~44
RIGHT : 1~45
OFF : HLC MASK OFF
D-W DR SET LEVEL 0~20 : DWDR level adjust
3D-DNR OFF, LOW, MID, HIGH, AUTO
Reduce noise in low illumination
(Level selectable)
RETURN Move back to previous menu
2. WHITE BALANCE
AWB MODE
ATW Color temperature 2500~9500 K °
MANUAL
M-W R 0~128 : Adjust the Red value to shift the color of
the object
M-WB 0~128 : Adjust the Blue value to shift the color
of the object
RETURN Move back to previous menu
PUSH Find the optimal white balance for current
luminance environment
R-Y GAIN 0~255 Adjust Red tone of the image
B-Y GAIN 0~255 Adjust Blue tone of the image
RETURN Move back to previous menu
3. DAY&NIGHT
D&N MODE
AUTO
DAY NIGHT→
7~30
Select brightness of illumination about
changing the day↔night mode by AGC
NIGHT DAY→
6~29
DELAY TIME
0~15 : Select the duration time
RETURN Move back to previous menu
AUTO-CDS
A.DAY→NIGHT
6~36
Select brightness of illumination about
changing the day↔night mode by AGC
A.NIGHT→DAY
6~36
C.DAY→NIGHT
0~255
Select brightness of illumination about
changing the day↔night mode by CDS
C.NIGHT→DAY
0~255
DELAY TIME
0~15 : Select the duration time
RETURN Move back to previous menu
COLOR Fixed at color
B&W Fixed at B/W
EXT DELAY TIME
0~15 : Change the color↔B/W by external signal(N/A)
RETURN Move back to previous menu
BURST ON, OFF Transmit the burst signal or not in B/W mode
C_SUP 0~100 Color suppress controllable
A_SUP 0~100 Iris suppress controllable
SMART IR ON, OFF Decreases screen saturation of objects within a
short range
RETURN Move back to previous menu
OSD Menu
Select Menu
Sub Menu Summary
4. IMAGE ADJUST
MIRROR MIRROR, OFF Set a vertical image inversion
SHARPNESS
0~30 Sharpness adjustable
GAMMA
0.45, 0.55, 0.65 Set a gamma value
USER GAMMA
0.20, 0.25, 0.30, 0.35, 0.40, 0.45, 0.50, 0.55,
0.60, 0.65, 0.70, 0.75, 0.80, 0.85, 0.90, 0.95,
1.00 : Gamma adjustable
RETURN Move back to previous menu
LSC ON SET LEVEL 0~30 : Use the LSC and level adjustable
RETURN Move back to previous menu
OFF LSC OFF
RETURN Move back to previous menu
5. MOTION
MOTION ON, OFF Motion detection function activate/deactivate
AREA AREA 1~4
TOP 0~143
Make a zone for motion detection
BOTTOM 2~145
LEFT 0~190
RIGHT 2~192
RETURN Move back to previous menu
RETURN Move back to previous menu
SENSITIVITY
1~30 Motion detection sensitivity
DISPLAY OFF, MESSAGE, TRACE Select notification method of motion detection
HOLD TIME 0~15 Set the duration of alarm out
ALARM
OUTPUT ON, OFF Alarm ON/OFF
RETURN Move back to previous menu
6. PRIVACY
MASK 1~8
OFF Display each privacy mask or not
ON
DOT SEL
L_TOP, L_BOT, R_BOT, R_TOP
: Determines which of the 4 vertices of each MD
area is to be used
DOT XY ENTER SETTING : Determines the coordinate
MOVE XY ENTER SETTING : Move the mask
COLOR BLACK, WHITE, … : Select mask color(8 colors)
RETURN Move back to previous menu
RETURN Move back to previous menu
7. SPECIAL
LANGUAGE ENGLISH, … : Select language(9 languages)
TITLE OFF--ON
EDIT Display the camera name on the screen
RESET Camera name reset
POSITION Camera name position
RETURN Move back to previous menu
COMMUNI-
CATION
(N/A)
OFF--ON
ID 1~255 : Select the camera ID for RS-485
communication
BAUDRATE 2400, 4800, 9600 : Select baud rate
PROTOCOL PELCO-D : Camera protocol
RETURN Move back to previous menu
DPC
OFF Deactivates Defect Pixel Correction in low
illumination
AUTO
WHITE THR 0~255 : Setup the limited value of white pixel
correction
LUMA THR 0~255 : Setup the limited value of white pixel
correction
RETURN Move back to previous menu
FACTORY
SET YES, NO Reset your camera to factory default condition
RETURN Return to previous menu
(Communication setting is not changed)
8. EXIT
SAVE AND
EXIT Save the value and exit menu
EXIT Escape the menu without save
RETURN Move back to previous menu
Speco Technologies is constantly developing product improvements. We reserve the right
to modify product design and specifications without notice and without incurring any
obligation.
Rev. 08/17/12.
HLED31D1B, HLED31D1W
HLED31D7B, HLED31D7W
3B25276B

Specyfikacje produktu

Marka: Speco Technologies
Kategoria: Kamera monitorująca
Model: HLED31D7W

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Speco Technologies HLED31D7W, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje Kamera monitorująca Speco Technologies

Speco Technologies

Speco Technologies O5LB1 Instrukcja

12 Stycznia 2025
Speco Technologies

Speco Technologies O2P30X Instrukcja

12 Stycznia 2025
Speco Technologies

Speco Technologies O8B7M Instrukcja

11 Stycznia 2025
Speco Technologies

Speco Technologies VLDT3GM Instrukcja

22 Września 2024
Speco Technologies

Speco Technologies CVC624WDR Instrukcja

20 Września 2024
Speco Technologies

Speco Technologies O4iB2M Instrukcja

20 Września 2024
Speco Technologies

Speco Technologies ZIPTW4B1 Instrukcja

18 Września 2024
Speco Technologies

Speco Technologies O2ID21M Instrukcja

18 Września 2024
Speco Technologies

Speco Technologies Intensifier 2 CVC6246iHR Instrukcja

18 Września 2024
Speco Technologies

Speco Technologies O4DT1 Instrukcja

18 Września 2024

Instrukcje Kamera monitorująca

Najnowsze instrukcje dla Kamera monitorująca

Dahua Technology

Dahua Technology Pro IPC-HDPW5442G-Z Instrukcja

15 Stycznia 2025
Toshiba

Toshiba IKS-WR7412 Instrukcja

13 Stycznia 2025
AVerMedia

AVerMedia FC1320-P Instrukcja

13 Stycznia 2025
Digitus

Digitus OptiMax DN-16037 Instrukcja

13 Stycznia 2025
Hikvision

Hikvision DS-2CE59U1T-AVPIT3ZF Instrukcja

12 Stycznia 2025
Hikvision

Hikvision IDS-2CD7526G0-IZHSY Instrukcja

12 Stycznia 2025
Hikvision

Hikvision DS-2CD2163G0-I(S) Instrukcja

12 Stycznia 2025
Hikvision

Hikvision DS-2CD2H83G1-IZS Instrukcja

12 Stycznia 2025
ZKTeco

ZKTeco AntarVis 2.0 Instrukcja

12 Stycznia 2025
Kguard

Kguard QRT-501 Instrukcja

11 Stycznia 2025