Instrukcja obsługi Soundsphere SS-Q-12A
Soundsphere
głośnik
SS-Q-12A
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Soundsphere SS-Q-12A (2 stron) w kategorii głośnik. Ta instrukcja była pomocna dla 6 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek
Strona 1/2
SS-Q-12A & SS-Q-12-AWR
OWNER’S MANUAL
© 2021 MSE Audio. Rev. 02.25.2021
360º of the Best Sound Around™
Contact: MSE Audio, 855.663.5600 / 913.663.5600 / sales@mseaudio.com
Please read the following instructions carefully before installing
your Soundsphere® speaker. If you have any questions
regarding installation that are not answered in the following
directions, please contact your local sound contractor or the
Soundsphere®/MSE Audio® technical support team.
General Information
Maximum Amplier Power 250 Watts RMS
Nominal Impendance 8 ohms
Wiring
Amplier connection is via ying leads. Connect the positive
(+) amplier lead to the RED input wire. Connect the negative
(-) amplier lead to the BLACK wire. Secure connections using
wire nuts, etc. Please see next page for Q-12-AWR wiring.
Mounting
Hanging Kit
Mount using one of the following methods:
a) Properly secured wire rope with a minimum breaking
strength of 400 lbs. (for a 10:1 safety factor).
b) Beam clamp with proper load rating.
It is recommended to use a secondary wire rope support around
one of the legs. The use of Do not use rope for mounting.
chain is not recommended unless rated for suspension of loads
greater than or equal to 400 lbs (for a 10:1 safety factor).
Surface Mount Bracket
Secure the bracket to the hard surface using proper hardware.
Secure the speaker to the bracket using the washers and nylon
locknuts provided. It is recommended to use a secondary wire
rope support around one of the legs and through an unused
bracket hole.
Warranty
Soundsphere loudspeakers carry a 5 year limited warranty. See
warranty sheet for details and limitations.
Replacement Parts
12” 250 Watt coaxial loudspeaker driver with crossover.
Order Model Number CX-12
Always check local requirements for overhead suspension
of loudspeakers.
Replacing the Coax Driver and Crossover in the Q-12A
1. Remove the reector from the Q-12A by removing the 3
bolts, washers, and tabs.
2. Remove the 8 screws securing the driver. Remove the
driver by pushing up on it through the port hole in the
sphere with one hand and removing it with the other
hand. Pull the wire out through the hole in the bolt.
3. Feed the wire from the replacement driver through the
drilled bolt inside the sphere. Install the new driver and
secure with screws.
5. Replace the reector. The washer order is metal washer to
leg, then rubber washer, reector, rubber washer, metal
washer and bolt (see gure below). Feed the wire through
the washers and the drilled bolt. Tighten bolts until the
rubber washers begin to deform.
Other Information
Wire runs between the amplier(s) and loudspeaker(s) must be
of the appropriate gauge to insure the full audio performance
capabilities of the Soundsphere loudspeakers. This applies to
all loudspeaker impedances (4 or 8 Ohms) or audio line volt-
ages (50, 70.7 or 100 Volts). For more information, please see
the ‘Downloads” section at www.soundsphere.com, or call our
Customer Service at 913.663.5600.
Leg Bolt
Tab
Metal Washer
Rubber Washer
Reector
Rubber Washer
Metal Washer
Leg
WARNING
Be sure to securely tighten all hardware before hanging the loudspeaker. Wire rope (steel cable), cable clamps with saddles and
thimbles of suitable size and strength are the recommended materials for overhead suspensions. All loudspeakers should be
redudantly safety wired to structural members of the building with an approved safety wire system or other agency certied materials.
IMPORTANT: Always check local safety codes before installing any overhead loudspeaker system and for periodic inspection
and maintenance of the installation.
SS-Q-12A & SS-Q-12-AWR
OWNER’S MANUAL
© 2021 MSE Audio. Rev. 02.25.2021
360º of the Best Sound Around™
Contact: MSE Audio, 855.663.5600 / 913.663.5600 / sales@mseaudio.com
Wiring for SS-Q-12-AWR
Remove Cover
Choose Tap Setting
Choose the Tap setting and connect the red and black wires
from the input connector to the transformer wire using the
supplied wire crimp.
COVER
Specyfikacje produktu
Marka: | Soundsphere |
Kategoria: | głośnik |
Model: | SS-Q-12A |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z Soundsphere SS-Q-12A, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje głośnik Soundsphere
20 Czerwca 2024
20 Czerwca 2024
Instrukcje głośnik
- głośnik Yamaha
- głośnik Ikea
- głośnik Sven
- głośnik LG
- głośnik Logitech
- głośnik Pioneer
- głośnik Philips
- głośnik SilverCrest
- głośnik JBL
- głośnik Onkyo
- głośnik KEF
- głośnik Bose
- głośnik Klipsch
- głośnik Crestron
- głośnik Behringer
- głośnik Nedis
- głośnik Be Cool
- głośnik Medion
- głośnik Boss
- głośnik Marquant
- głośnik Jensen
- głośnik ILive
- głośnik Blaupunkt
- głośnik Speed-Link
- głośnik Martin Logan
- głośnik Grundig
- głośnik Genesis
- głośnik Hyundai
- głośnik Creative
- głośnik Manhattan
- głośnik Xmusic
- głośnik Denon
- głośnik Phoenix Gold
- głośnik Audac
- głośnik Cambridge
- głośnik Edifier
- głośnik Kenwood
- głośnik Polk
- głośnik Gembird
- głośnik Dynaudio
- głośnik Paradigm
- głośnik Bang & Olufsen
- głośnik Cobra
- głośnik Trust
- głośnik Memphis Audio
- głośnik Jamo
- głośnik Biltema
- głośnik Auna
- głośnik LD Systems
- głośnik Krüger&Matz
- głośnik Mad Dog
- głośnik OneConcept
- głośnik Renkforce
- głośnik Clarion
- głośnik Wharfedale
- głośnik Magnat
- głośnik Pyle
- głośnik ELAC
- głośnik Sonus Faber
- głośnik Speco Technologies
- głośnik Lenoxx
- głośnik Bowers & Wilkins
- głośnik Samson
- głośnik Monitor Audio
- głośnik Audio Pro
- głośnik Vonyx
- głośnik Alto
- głośnik Fluid
- głośnik Peavey
- głośnik ION
- głośnik RCF
- głośnik Harman Kardon
- głośnik Rolls
- głośnik Audio-Technica
- głośnik GoGen
- głośnik Aiwa
- głośnik JL Audio
- głośnik Axis
- głośnik Acoustic Energy
- głośnik REL Acoustics
- głośnik Teufel
- głośnik Dali
- głośnik Hifonics
- głośnik Focal
- głośnik Amazon
- głośnik Omnitronic
- głośnik Hama
- głośnik Mackie
- głośnik VIETA PRO
- głośnik Deaf Bonce
- głośnik Mac Audio
- głośnik Hertz
- głośnik Atlas Sound
- głośnik Trevi
- głośnik Soundcore
- głośnik Power Dynamics
- głośnik Rockford Fosgate
- głośnik Canton
- głośnik Monacor
- głośnik Tannoy
- głośnik Electro-Voice
- głośnik Audizio
- głośnik JAYS
- głośnik Cavalier
- głośnik Alfatron
- głośnik Indiana Line
- głośnik Reflexion
- głośnik HK Audio
- głośnik Fenton
- głośnik Speaka
- głośnik BZBGear
- głośnik OWI
- głośnik TrekStor
- głośnik Finlux
- głośnik Sonance
- głośnik Pulver
- głośnik Atlas
- głośnik Devialet
- głośnik Cabasse
- głośnik ACME
- głośnik Lexon
Najnowsze instrukcje dla głośnik
10 Lipca 2024
10 Lipca 2024
10 Lipca 2024
9 Lipca 2024
9 Lipca 2024
9 Lipca 2024
9 Lipca 2024
9 Lipca 2024
8 Lipca 2024
8 Lipca 2024