Instrukcja obsługi Soundskins SSK-BRONCO4DR


Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Soundskins SSK-BRONCO4DR (2 stron) w kategorii Niesklasyfikowane. Ta instrukcja była pomocna dla 6 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Strona 1/2
Bronco Kit Door Installation Instructions
1. Start by locating the fastening hardware on the door panels.
There will be one behind the door handle under a plastic cover,
one behind the door grab handle that you will have to pop out
to reveal, and 2 at the bottom right corner of the door panels.
Take a 7 mm socket and remove. Then, use a panel tool to pry
the panel off the door, start from the bottom right corner. Be
sure not to break any clips or mounting hardware.
3. Now, apply the door pieces. Peel off the backing paper
starting at the top, tack the piece onto the door and work your
way down, pressing down the material and pulling down the
backing paper more as you go along. Feed the harnesses
through the proper holes and ensure everything is aligned
before pressing the entire piece down. Repeat steps 1-3 for all
doors. Then replace your door panels and reconnect the wires
and enjoy your quiet new ride!
2. Pull the door panel away slowly. There will be 2 plug clips
that will need to be released as well as a wire plug to
disconnect. Set the door panel aside and unhook all plugs,
remove the vapor barrier, and clean the car metal surface
using a microfiber cloth and Acetone or other cleaning solution.
The point is to get the surface clean to ensure material glue
contact.
Soundskins USA
13452 Alondra Blvd, Cerritos, CA 90703
Phone: 877.211.5597
Email: team@soundskinsglobal.com
www.SoundSkinsGlobal.com
R
• 7mm socket
• Socket extension
• Panel /trim tool
• Roller
• Microber cloth
• Acetone or cleaning solution
Tools needed for installation: Scan this code to watch the
full instructional video!
4 Piece Custom Cut PRO KIT
2021+
Recommended Installation Instructions
A. Prepping the Surface
After removing interior door panels, you are ready to clean the metal areas that will be insulated. If the metal has a
“new” look without imperfections, then take a microfiber cloth and wipe away any dust and debris. If the metal is
showing signs of age like rust, we recommend using Acetone with a breathing mask to wipe off debris and loose
particles. A shop vacuum might be needed to remove loose debris on the floorboard.
B. Installing Panels
Now that you have a clean surface, you are ready to start applying the sheets. We recommend using a roller to
release air pockets that might be lingering from trapped air. You want to make sure that you have rolled those out to
the edge and all the material has a good seal to the metal surface. Make sure all pieces are installed and inspected
before reinstalling the interior.
1) Driver Front Door Panel 2) Driver Rear Door Panel
3) Passenger Front Door Panel 4) Passenger Rear Door Panel
1
2
3
4


Specyfikacje produktu

Marka: Soundskins
Kategoria: Niesklasyfikowane
Model: SSK-BRONCO4DR

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Soundskins SSK-BRONCO4DR, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą




Instrukcje Niesklasyfikowane Soundskins

Instrukcje Niesklasyfikowane

Najnowsze instrukcje dla Niesklasyfikowane

Stihl

Stihl HT 70 Instrukcja

15 Października 2024
Ernesto

Ernesto H14270 Instrukcja

15 Października 2024
Uniden

Uniden BT MIC KIT Instrukcja

15 Października 2024
Vaude

Vaude Omnis Bike 26 Instrukcja

15 Października 2024
ART

ART ProChannel II Instrukcja

15 Października 2024
Aukey

Aukey DR02J Instrukcja

15 Października 2024
Master Lock

Master Lock 653EURD Instrukcja

15 Października 2024
Roland

Roland FR-18 Diatonic Instrukcja

15 Października 2024