Instrukcja obsługi Sound Devices MP-1

Sound Devices mikser MP-1

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Sound Devices MP-1 (8 stron) w kategorii mikser. Ta instrukcja była pomocna dla 3 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/8
©2001–2007 Sound Devices, LLC
Sound Devices, LLC
300 Wengel Drive
Reedsburg, WI 53959 USA
Voice +1 (608) 524-0625
Fax +1 (608) 524-0655
www.sounddevices.com
MP-1
Microphone Preamplifi er
User Guide and Technical Information
MP-1 Microphone Preamplifier
User Guide and Technical Documentation
page 4
Sound Devices’ MP-1 is a portable, battery-powered microphone preamplifi er with phantom power. De-
signed for high-resolution fi eld production, this studio-quality mic pre is ideal for critical radio, televi-
sion, and fi lm production applications.
With its rugged mechanical and electrical construction, compact size and high-quality components, the
MP-1 will provide years of superb audio performance under the most punishing fi eld conditions.
Audio Performance
• Maximum of 66 dB of gain, adjustable in eleven discrete steps for accurate, repeatable gain set-
tings
• Dynamic range exceeding 120 dB
• 20 Hz to 50 kHz audio bandwidth
• High immunity to RF interference due to transformers, RF fi ltering, and all-metal construction
• High current line output driver capable of driving very long cable runs
Transformer-Balanced
• Premium quality input transformer provides superior sonic quality and freedom from interfer-
ence problems
• Custom-designed output transformer provides line driving ability with freedom from interfer-
ence problems
Limiter
• Extended range peak limiter via dual opto-isolators makes unit virtually “unclippable”
Battery Powered
• Internal battery power (two AA) for convenient, low cost power
• Battery life greater than 24 hours (phantom power off)
Durable Mechanical Construction
• High strength extruded aluminum chassis with protective metal end rails to withstand punish-
ing fi eld conditions
• Easy access battery compartment for quick battery changes
Phantom Power
• Selectable 48-volt and 12-volt phantom power for condenser and dynamic microphones
High-Pass Filter
• Two selectable corner frequencies, 80 and 160 Hz, 6 dB per octave
page 5
Frequency Response: 20 Hz to 22 kHz, +0.1, -0.5 dB, –1 dB at 50 kHz (relative to 1 kHz level with 150 ohm source)
-6
+1
-5
-4
-3
-2
-1
+0
d
B
u
10 100k20 50 100 200 500 1k 2k 5k 10k 20k 50k
Hz
Gain: 0 dB to 66 dB input to output, switch selectable
Gain Accuracy: +0.6, –0.1 dB with reference to front panel gain markings
(150 ohm source, 100k ohm load impedances)
Equivalent Input Noise: –126 dBu (–128 dBV) minimum
(150 ohm source, fl at weighting, 22–22 kHz bandwidth, gain setting 36 dB or greater
Output Clipping Level: +22 dBu minimum with 100k ohm load
+20 dBu minimum with 600 ohm load
Input Clipping Level: +4 dBu minimum at the 0 or +18 dB gain setting
Dynamic Range: 122 dB minimum at the +18 dB gain setting
THD + Noise: 0.05% maximum (from 50 Hz – 22 kHz @ +4 dBu output level, +46 dB gain setting)
Common Mode Rejection Ratio: 100 dB minimum at 80 Hz
60 dB minimum at 10 Hz
Input: Transformer-balanced, 2000 ohm input impedance
Output: Transformer-balanced, 130 ohm output impedance
Low Cut: 80 Hz or 160 Hz (switch selectable), 6 dB per octave
Phantom Power: 12-volt or 48-volt (switch selectable) per DIN 45 596 specification
Limiter: Limits to +17 dBu output level 10:1 limiting ratio; 5 mS attack time, 100 mS release time;
Amber/Red LED indicates limiting/clipping
Internal Voltage Rails: ±15 V, regulated
Power: 2 AA batteries, 24 hours life typical with +4 dBu signal into 600 ohms, no phantom power.
Power LED: Green indicates power and good battery. Red indicates power with low batteries. LED turns red when
approximately 4 hours of battery life remain.
Polarity: Mic input to line output is non-inverting
Operating Temperature Range: 0° to 70° C 32° to 160° F
Dimensions: 43 mm x 94 mm x 140 mm (h x w x d)
(1.7” x 3.7” x 5.55”)
Weight: (unit only): 0.56 kg, 1.24 lbs (unit only)
0.86 kg, 1.90 lbs (packaged)
Certification: Meets FCC Part 15 Class B
Eligible to bear CE mark (see conformance statement)

Specyfikacje produktu

Marka: Sound Devices
Kategoria: mikser
Model: MP-1

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Sound Devices MP-1, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje mikser Sound Devices

Sound Devices

Sound Devices CL-16 Instrukcja

22 Sierpnia 2024
Sound Devices

Sound Devices 552 Instrukcja

22 Sierpnia 2024
Sound Devices

Sound Devices MM-1 Instrukcja

10 Czerwca 2024
Sound Devices

Sound Devices MP-1 Instrukcja

10 Czerwca 2024

Instrukcje mikser

Najnowsze instrukcje dla mikser

Braun

Braun MultiQuick 7 MQ7025X Instrukcja

15 Stycznia 2025
Domo

Domo My Blender Family DO492BL Instrukcja

14 Stycznia 2025
Breville

Breville the Kinetix Control BBL605 Instrukcja

14 Stycznia 2025
Krups

Krups Perfect Mix 5000 Plus HZ2031 Instrukcja

14 Stycznia 2025
Breville

Breville The Boss To Go BSS500BRR Instrukcja

14 Stycznia 2025
KitchenAid

KitchenAid RKSB560BF Instrukcja

12 Stycznia 2025
Gorenje

Gorenje BSM600LBW Instrukcja

12 Stycznia 2025
Heinner

Heinner HHB-DC1000SSBK Instrukcja

12 Stycznia 2025
Midea

Midea MNM802TSBPH Instrukcja

12 Stycznia 2025
Oster

Oster BLSTKAP-RRD Instrukcja

11 Stycznia 2025